Ganz C-AllView Assembly instructions

C-AllView &
C-AllView Ti
installer’s guide

1
Contents
Introduction 2
Welcome 2
Installation 3
Camera mounting 3
Camera telemetry settings 6
Power and signal connections 9
Camera power requirements 9
Mains power supply (C-ADN3 models) 9
Fuses 10
Connecting the composite cable 10
Connecting external links 11
Vehicle power supply (C-ADN3V models) 12
Thermal image focusing (Ti models only) 13
Further information 14
WEEE statement 14
Changes to control protocols 14
Safety 14
Disclaimer 14
Dimensions 15
Camera Unit 15
Specifications: Mechanical and general items 16
Specifications: Camera modules 17

2
Introduction
Welcome
These are no ordinary cameras. Thanks to careful development and rigorous
testing, these cameras are equipped to survive in harsh environments and provide
enhanced features. Two main models are available to offer optical only or optical
plus thermal imaging abilities.
The numerous benefits of both camera types include:
• Flat toughened glass window – scratch resistant, maintenance-free and optically
correct,
• Integral Wiper – to clean away rain and deposits caused by wind, sea spray and
road traffic,
• Hard anodised aluminium castings, with optional powder coating to prevent
corrosion in the harshest of marine environments,
• M4 marine grade stainless steel case fastenings,
• Optional washer system,
• Optional infra-red LED illumination system,
• Day/night switching by external contact closure (optional alarm interface),
• Multiple native control protocols: Coaxial and RS485,
• Optional RS485 alarm interfaces.
Optical only Optical plus
thermal imaging

3
Installation
Camera mounting
The camera is designed to be mounted upright or hang-
ing. By nature of its rugged construction the camera is
a heavy item and thus requires a substantial and stable
mounting. The camera is supplied with a mount adaptor to
allow fixing to industry standard brackets, towers or columns.
The mount adaptor has two cable entry points:
• A pass-through hole in the end plate to allow the com-
posite cable to enter unseen from a column, tube or
bracket type mounting, plus
• A conduit thread (M25) in the side wall to permit com-
posite cable entry via a flexible conduit attached to the adap-
tor.
To mount the camera
1 Thread the composite cable through the appropri-
ate entry hole into the mount adaptor before it is
fixed to the column or bracket.
2 To avoid placing strain upon the electrical connections,
arrange the composite cable such that approximately
25~35mm of the weatherproof connector protrudes
out from the smaller plate that will connect to the
camera.
3 Secure the mount adaptor to
the supporting structure us-
ing M8 bolts, washers and
Nyloc®type nuts.
IMPORTANT: Always use
Nyloc nuts in order to signifi-
cantly reduce the possibility of bolts
working loose during operation due to
vibration.

4
4 Offer the camera to the mount adaptor and clip the
lanyard onto the lug of the mount adaptor. In
addition to being an essential safety device during
operation, the lanyard is useful as a temporary
hanging point when the camera is being
mounted in the inverted position.
5 Carefully note the orientation notch-
es of cable connector and camera
socket. Align the notches accordingly
and insert the connector onto the socket
of the camera base. Twist the connector’s
retaining ring until it locks into place.
6 Remove the four hex head bolts from
the camera base and push the connector
back into the mount adaptor.
7 Align the four holes of the mount adaptors with those on the camera base and
insert the four hex head bolts.
8 Tighten the bolts to approximately 1.6Kg/m. Do not over tighten bolts.
IMPORTANT: Ensure that the lanyard is connected to the appropriate lug
on the mount adaptor when the camera mounting is complete. Also, dou-
ble check all bolts for correct positioning and appropriate tightness.

5
To offset the camera head
When mounting upright, the camera head
can be offset to allow it a field of view
clear of the pan motor section of the hous-
ing.
1 Unscrew and withdraw the M5 socket
head retaining bolt from the middle of
the front of the yoke.
2 Carefully tip the yoke assembly forward.
3 Re-insert the bolt from the rear of the
yoke and tighten to approximately
0.97Kg/m. Do not over tighten the bolt.

6
Camera telemetry settings
Depending on the chosen protocol, telemetry control signals may be fed to the
camera either via the primary co-axial video link cable or through the twisted pair
cables that are included within the composite cable.
Note: Due to limitations or software changes within some protocols, it is not always
possible to implement all of the camera’s features.
All settings related to telemetry control are configured using two banks of switches
(S1 and S2) located behind a removable panel within the hub of the camera.
To access the switches, remove the two retaining screws and remove the panel:
Note: In all switch setting tables, a dash (-) means the corresponding switch is Off.
Device ID address (block S1, switches 1 to 8)
For protocols which use RS485 control signals via the twisted pair link within the
camera’s composite cable, you can determine the device ID address for the camera.
Note: These settings are ignored for protocols that use the primary video coaxial
cable to transfer telemetry signals.
Device ID S1-1 S1-2 S1-3 S1-4 S1-5 S1-6 S1-7 S1-8
0 - - - - - - - -
1 On - - - - - - -
2 - On - - - - - -
3 On On - - - - - -
4 - - On - - - - -
5 On - On - - - - -
6 - On On - - - - -
7 On On On - - - - -
8 - - - On - - - -
9 On - - On - - - -
10 - On - On - - - -
11 On On - On - - - -
12 - - On On - - - -
13 On - On On - - - -
14 - On On On - - - -
8
7
6
5
4
3
2
1
8
7
6
5
4
3
2
1
8
7
6
5
4
3
2
1
8
7
6
5
4
3
2
1
S2
S1

7
Device ID S1-1 S1-2 S1-3 S1-4 S1-5 S1-6 S1-7 S1-8
15 On On On On - - - -
16 - - - - On - - -
17 On - - - On - - -
18 - On - - On - - -
19 On On - - On - - -
20 - - On - On - - -
21 On - On - On - - -
22 - On On - On - - -
23 On On On - On - - -
24 - - - On On - - -
25 On - - On On - - -
26 - On - On On - - -
27 On On - On On - - -
28 - - On On On - - -
29 On - On On On - - -
30 - On On On On - - -
•
127 On On On On On On On -
128 - - - - - - - On
129 On - - - - - - On
•
To determine Device IDs that are not listed here
Determine how many of the numbers shown below in bold are required
to make up the value of the Device ID number that you require. If a bold
number is needed to make up your number, then the corresponding switch
on the S1 block should be On. For example, to make the Device ID 85, you
need the values 1 + 4 + 16 + 64, thus switches S1-1, S1-2, S1-5 and S1-7
would need to be On, all others would be Off.
1 2 4 8 16 32 64 128
(S1-1) (S1-2) (S1-3) (S1-4) (S1-5) (S1-6) (S1-7) (S1-8)
•
245 On - On - On On On On
246 - On On - On On On On
247 On On On - On On On On
248 - - - On On On On On
249 On - - On On On On On
250 - On - On On On On On
251 On On - On On On On On
252 - - On On On On On On
253 On - On On On On On On
254 - On On On On On On On
255 On On On On On On On On

8
Telemetry protocol (block S2, switches 1 to 5)
Vendor Protocol Identity Link S2-1 S2-2 S2-3 S2-4 S2-5
360-Vision C-Dome 0C VIS360 RS485 - - On On -
BBV Serial485 12 BBV485 RS485 - On - - On
CBC OCP OCP485 00 OCP485 RS485 - - - - -
DeView VTC485 09 VTC485 RS485 On - - On -
Forward Vision FV Mic1-300 0D FV300 RS485 On - On On -
Ikegami I-LAN 0E IKILAN RS485 - On On On -
Ikegami RS485 0B IK485 RS485 On On - On -
Kalatel DP 05 KALADP RS485 On - On - -
Pelco D D2400 0A PELD24 RS485 - On - On -
Pelco P P4800 02 PELP48 RS485 - On - - -
Pelco P P9600 01 PELP96 RS485 On - - - -
Philips 2400 04 PHL24 RS485 - - On - -
Philips 9600 03 PHL96 RS485 On On - - -
Samsung SCC2000 0F SCC200 RS485 On On On On -
Samsung SCC3000 08 SCC300 RS485 - - - On -
Sensormatic - 06 SENSO RS485 - On On - -
Ultrak/Honeywell Diamond 07 ULTRK RS485 On On On - -
VCL - 11 VCL485 RS485 On - - - On
Baxell DC FSK-Standard 1E BAXDC Coaxial - On On On On
BBV Coaxial 1F BBVCAX Coaxial On On On On On
Pelco Coaxitron 18 PELCAX Coaxial - - - On On
Device termination (block S2, switch 8)
For protocols which use RS485 control signals via the twisted pair link within the
camera’s composite cable, you can determine whether or not the camera is termi-
nated. The camera should be terminated whenever it is situated as either the only
device connected to a controller or the last device within a chain of similar devices.
Note: This setting is ignored for protocols that use the primary video coaxial cable
to transfer telemetry signals.
Termination S2-8
Un-terminated Off
Terminated On