Ganz ZN-D100VE Instruction manual


2010/2‐1

1
ZN-D100VEQuickUserGuide

ThismanualhasbeendesignedtoguideyouthroughbasicsettingsofyourIPdevices,suchasinstallationand
configurationforusingthem.

Step1..AssembleandinstallIPdevice
Manualadjustmentfor3‐axismovements

Afterinstallation,makeamanualadjustmentontheinnerliner.Perform3‐axismovementsmanuallyby
turningtheinnerlinertodifferentdirectionsasabove,andcheckifitmovesproperly.Afteradjustment,
fastenthescrewoftherotationaxis.



LensFocusAdjustment



1) Openthedomecoverfromthedevice.
2) Uncoverthelatch(C)carefullyto
removethelenscover.
3) Rotatethelensfocusring(D)toadjust
thefocusandfastenthescrew(E)
usingtheincludedhexwrench.
4) Pushthelenscovertothemodule
untilthelatch(C)clicksintoposition.
5) Attachthedomecoverbyaligning
protrusiononthebody(B)withthe
invertedtrianglemarkofthedome
cover(A).Turnthedomecover
clockwisetolock.
A
B

C
*Modelshereinandtheirappearancearesubjecttochangewithoutanypriornotice.
D

E


2010/2‐1

2
Installation





 
1)ConnecttheLANcableandpower
supplycablewiththecamera.Forthe
detailedinformation,pleasereferto
theStep2.


2)Placetheinstallationtemplate
(whichisincludedinthepackage)on
theceiling.


3)Drilltwoholesonthetemplateand
insertanchorblocksintotheholes.
Fastenthecamerawithscrews.

4)Putthedomecoveronthemain
bodyofthecamera.Makesurethe
mainbodyandthecoverfiteachother
intoplace.

Whenassemblingthemainbodyofthecameraanditsdomecover,makesuretheyfit
eachotherintoplace.

Thecameramayfallofftheceilingevenaftertheproperinstallationandmounting.To
preventanyaccident,makesuretheceilingisfirmandstableenoughtosupportthe
camera.Ifanyreinforcementisneeded,consultwithyoursafetypersonnelandproceed
withtheinstallation.
Caution
!



2010/2‐1

3
Step2.ConnectcablestoIPdevice
Connecteachcabletothedevice.Toseethecorrectpositionsofallconnectors,refertothefollowingimage
below.


Step3.Setupnetworkenvironment
ThedefaultIPaddressofyourIPdeviceis192.168.XXX.XXX.YoucanfindtheavailableIPaddressfromthe
MACaddressofyourdevice.PleasemakesurethedeviceandyourPCareonthesamenetworksegment
beforerunningtheinstallation.IfthenetworksegmentwasdifferentbetweenyourPCandthedevice,change
yourPC’ssettingsasbelow.

IPaddress:192.168.xxx.xxx
Subnetmask:255.255.0.0

LAN
DC12V
Makesurethepolarityiscorrect.Incorrectconnectionmay
causemalfunctionordamagetotheIPdevice.
Caution
!PowerAdaptorConnector(DC12V)

*Modelshereinandtheirappearance
aresubjecttochangewithoutanyprior
notice.


2010/2‐1

4
STEP4.Viewvideoonwebpage
ViewthelivevideoonawebpageusingyourIPdeviceanditsIPaddress.TohavethecorrectIPaddress
readyanduseitonawebpage:
1. ConvertaMACaddresstoanIPaddress.
(TheMACaddressisattachedonthesideorbottomofthedevice.)



2. OpenawebbrowserandentertheIPaddressofthedevice.
3. ClickContinuetothiswebsite(notrecommended)asbelow.
(TheexplanationandcapturedimagesatthismanualaremainlyonthebasisofInternetExplorer7.0)


4. Clickpop‐upblockedandinstalltheActiveXcontrolasbelow.YouneedtoinstalltheActiveXfor
displayingtheimages.



MACaddress=00‐1C‐B8‐C0‐14‐B1 →IPaddress=192.168.20.177
theHexadecimalnumbertoDecimalnumber.


2010/2‐1

5

5. Waitforafewsecondswhilethewebpageloads.Thelivevideoisdisplayedasbelow.


6. Ifthelivevideoisnotdisplayedand“CannotCreateXMLDOMDocumentInstallMSXML4.0”
messageisshownasbelow,pleasedownloadandInstallfromthelinkbelow.
http://www.microsoft.com/downloads/details.aspx?familyid=3144B72B‐B4F2‐46DA‐B4B6‐
C5D7485F2B42&displaylang=en
(VCALibraryrequiresMSXML4.0librarywhichisanxmlparsermadebyMicrosoft.)





2010/2‐1

6
Step5.SettingIPAddress
TosetuptheNetworkconfiguration:

1. ClickSetupontheupperrightofthewebpage.Theloginpageisdisplayedasbelow.
2. Enterthedefaultusername(root)andthedefaultpassword(pass),andthenselectOK.



3. ClickSystemOptions,andthenselectTCP/IPfromthedrop‐downmenu.

TochangetheIPaddress,pleasemakesuretocheckandhavethecorrectSubnetmaskandGatewayready.To
useDHCP,selectObtainanIPaddressviaDHCP.

Tolearnhowtosetupthewebpageforadvancedconfiguration,refertotheWebPageUser'sManual,which
isavailableontheSDKatthefollowingpath.
{SDK root}\DOC\
Thedefaultusername
andpasswordare:
rootandpass.


2010/2‐1

7
Advancedsetup(ZNS-GITIPAdminTool)
ZNS‐GITIPAdminToolisautilityprogramforIPproducts.FollowinglistshowsapartoffeaturesthatZNS‐GIT
IPAdminToolprovides.
zConfigureIPaddress,SubnetmaskandGateway
zShowsnetworkrelatedinformationsuchasMACaddress
zUpdatesfirmware
zRebootsthedevice
ZNS‐GITIPAdminToolisprovidedwithSDKatthefollowingSDKpath.
{SDK root}\BIN\TOOLS\AdminTool\

MoreInformation
Tolearnmoreaboutusingotherfeaturesofyourdevices,refertothemanual,whichisavailableontheSDKat
thefollowingpath.
{SDK root}\DOC\
