Garden Oasis 302-1136135 User manual

Warning
1. It is the consumer's responsibility to comply with any building codes,
ordinances, zoning limitations, or local homeowner's restrictions and
obtain any required permit, before purchase and installation of the
products.
2. Two persons are required for assembly. The tools required include
spanners (part Y and Z1 in below structure), stepladder and other
safety items such as gloves and hardhat. To avoid injury from exposed
sharp edges, it may be necessary to use the above safety equipment.
3. This unit will take at least 5 hours to set up. You must schedule
enough time to complete the assembly so you don't leave it
unattended if not fully assembled,even if bolted to the ground.
 Make sure that all components are in the box. Read instructions
carefully before starting the assembly.
Follow all instructions to assure the strength of the shelter.
Help from another person is required to assemble the shelter.
In order to avoid damage to the shelter and its components, use
appropriate tools. Do not use the structure as a support;a
stepladder is recommended.
Check all screws on a regular basis to maintain the solidity of
the structure.
Keep instructions and parts list for further use.
4. The screws to anchor on wood deck and concrete patio aren't
included.
Maintenance
If this shelter needs repairs,
DO NOT RETURN THE PRODUCT TO SEARS.
lIn case of a defective part or if a problem occurs while using this
Product, please contact SOJAG at 1866-901-1649
lUse the part number on the parts list to order at your retail store
lFor cleaning: Use a domestic soap or detergent and wash with warm
water using a sponge or fabric. Rinse with clean water.
Attention
Your shelter has been created for all four seasons and will
resist to snow accumulations of 3500 lb;however,we strongly
suggest removing any excess of snow on the roof.
The mosquito nets must be removed for winter storage.
WARRANTY
 Limited warranty applicable on parts only
Products distributed by SOJAG are built with high standard.
Products distributed by SOJAG are guaranteed against defective
materials for three (3) years based on normal use of the product.
EXCLUDED:
1. Damages due to vandalism, abuse and wrong use of the product is not
covered by the warranty.
Damage due to extreme weather conditions such as thunderstorm and
windstorm.

Roof side structure
Roof side structure
Roof side structure
Coner cover
J
J1
J2
Solidifying bar
Column cap
Joint cover plate
Cornice
Cornice
Cornice
Cornice

Na
Nb
M6x20
16PCS
8PCS
W
X
Allen
Z1
S1
M6x35
165PCS
O1
M6x16
72PCS
St5x16
8PCS
Y1
Z3
Z2
Solidifying bar
Solidifying bar

V
 Install columns (A) on bases (H) using
screws (V)
A
H
1
Step 1
Step 2
Assemble column
Assemble the cornice
Attach the (B) to the cornice (B1)
with screw (V). Repeat with the cornice (C
and C1)
cornice
C
C1
B
B1
V
/4 /4 /2 /2 /2 /2

2
Step 3 Assemble the structure
C
C 1
Install the (B and B1) between two (2)
columns and screw together with screw (T). Repeat
with the (C and C1)
cornice
cornice
V
TZ1
C1
C
B
B1
B1
B
C1
C
T

L
W
3
Step 4 Assemble corner covers and the joint cover plates
 Install the column caps (I1) on the columns (B2)
using screws V)
 Screw the joint cover plates (L) using screws (W)
on the joint between the (C and C1)
 Screw the corner covers (I) using screws (W)
cornice
I
W
V
I1
B2
W
/4 /4 /4

Step 5 Tracks installation
Install solidifying bars(K)inside each
structure bar using screws(V)
Install solidifying bars(Z2,Z3)inside each
structure bar and join the other end to the
columns using screws(V)
V
K
KK
Z2
Z3
Z3
Z2
V
K
V
Z2Z3
/4 /4 /4
Z2Z3
4

6xX
B2
 Slide 6 hooks (X) into each track section (B2)
and 7 hooks (X) into each track section (C2).
 Place tracks (B2) on the structure bars (B&B1)
ith screws (V). Repeat with sections (C2) on
the structure (C&C1).
1w
5
Step6 Tracks installation
7xX
C2
V
C2
V
B2
B2
C2
/4 /4 /52
X

Fix the roof side structure (G, G1 & G2) on the
(B, B1, C, & C1) using screw (W).cornice
Step 7 Tracks installation
6
GG2G
G
1
G1
W
B
W
/4 /4 /2