Garden Oasis Grandview User manual

1
Grandview 4 seat Glider
Date of purchase: _____/ _____/ _____
Product Code: D71 M23738
KSN Code: 04733850-4
UPC Code: 749241313264

2
SAFETY INFORMATION
Please read and understand this entire manual before attempting to assemble, operate or
install the product. If any parts is missing or damaged, do not attempt to assemble the product.
Two to four people are needed for assembly.
In order to avoid damage to the item and its components, use appropriate tools.
Check all screws on a regular basis to maintain the solidity of the structure.
Keep instructions and parts list for further use.
Estimated Assembly Time: Approx. 5 hours
CAUTION
Do not leave outside during high winds, heavy rains or snow.
WARRANTY
1 year limited warranty.
Limited warranty applicable on parts only. Warranty extends solely to the original purchaser, who
must offer the original sales receipt for record.
EXCLUDED
Damages due to vandalism, abuse and wrong use of the product is not covered by the warranty.
Damages due to extreme weather conditions such as thunderstorm and windstorm.
MAINTENANCE
If this shelter needs repairs, DO NOT RETURN THE PRODUCT TO SEARS.
In case of a defective part of if a problem occurs while using this Product, please contact Bond Vast
at 1-800-961-9838, 9AM ~ 5PM, Pacific Time Zone, Monday - Friday.
Or email us: [email protected].
WARNING
KEEP ALL FLAME AND HEAT SOURCES AWAY FROM TENT FABRIC.
This tent meets the flammability requirements of CPAI-84. The fabric may burn if left in
continuous contact with any flame source. The application of any foreign substance to the
tent fabric may render the flame-resistant properties ineffective.

H2 H1
FEAE
B
CD
F
B
C
I2 I1
G2 G1 L
I2
I1
L
J
M
P
R2
R1
O
Q
S
J
N
X1 X2
W
W
K
X2
X1
V
U
U
U
U
WW
T
V
3

4
Item Description Qty Illustration
A
B
C
D
E
F
G1
G2
H1
H2
I1
I2
J
K
L
2
2
2
1
2
4
2
2
2
2
2
2
2
4
1
Metal support
Side floor board
Center floor board
U shape support
Wheel axle
Wheel
Upper running 1
Upper running 2
Lower running 1
Lower running 2
Long side guard
Short side guard
Arm connector
Roof cover
Side guard
Part list

5
Item Description Qty Illustration
1
2
1
4
20
2
2
6
1
4
2
4
2
2
M
N
O
P
Q
R1
R2
S
T
U
V
W
X1
X2
Table top
Table leg
Table bracket
Armrest
Plastic cap
Seat 1
Seat 2
Seat bracket
Roof connector
Roof tube 1
Roof tube 2
Roof crossbar
Roof support bar
Roof support bar

6
IllustrationQtyDescription
Item
8
12
8
16
40
26
8
12
16
70
162
4
2
2
AA
BB
CC
DD
EE
FF
GG
HH
II
JJ
KK
LL
MM
NN
Screw 1 M6 x 110mm
Screw 2 M6 x 85mm
Screw 3 M6 x 65mm
Screw 4 M6 x 50mm
Screw 5 M6 x 30mm
Screw 6 M6 x 20mm
Screw 7 M6 x 15mm
Screw 8 M6 x 10mm
Screw 9 M6 x 70mm
Bolt nut
Washer
Pin
Hex wrench
Spanner
Hardware kit

7
C
D
X 2
X 1
C
JJ
KK
D
KK
EE
C
D
C
1
11
1
1
1
1
1
1
1. Lay out floor board (C) and floor board (D) side by side, stripped face upward as
shown. Then connect side floor board (C) with center floor board (D) by using
screw 5 (EE), washer (KK), bolt nut (JJ).
Repeat this step 7 times.

8
AX 2
C
D
C
A
1
A
1
1
1
1
1
1
1
GG
1
KK
A
C
1. Attached the metal support (A) on the assembled floor board (C, D) by using screw 7 (GG) and
washer (KK) as shown.
Repeat for the rest metal support (A).

9
EF
X 2 X 4
F
E
FF
LL
F
E
F
LL
F
1
1
2
2
1. Insert wheel axle (E) into wheel (F) and tighten with screw 6 (FF), then open the end of pin (LL)
and insert into the hole of wheel (F). Do not over tighten the screws. Repeat on the other end of
the wheel axle (E) as shown.
Repeat for the rest wheel axle (E) and wheel (F).

10
H1
H2
X 2
X 2 X 2
B
H2 H1
HH HH
KK
KK
HH HH
KK FF
JJ
B
KK
DD
H1
1
1
2
H2 H1
H2
H1
B
B
2
2
2
2
1. Insert lower running 1 (H1) into lower running 2 (H2) and secure by using 4pcs of screw 8 (HH)
and washer (KK). Repeat for the rest lower running 1 (H1) and lower running 2 (H2).
2. Connect assembled lower running set (H1, H2) with U shape support (B) using screw 4 (DD),
washer (KK) and bolt nut (JJ), then secure U shape support onto the assemble lower running set
by using screw 6 (FF) and washer (KK) as shown. Repeat on the other end of the U shape support
(B).
Repeat for the rest U shape support (B).

11
H1
C
C
D
H1
H2
H2
F
F
E
2
1
1
11
2
DD
KK
JJ
AF
E
12
1. Turn the floor board over (metal support A facing down), then tighten the metal support (A) onto
assembled lower running set (H1, H2) by using screw 4 (DD), washer (KK) and bolt nut (JJ) as
figure 1 shown. Do not over tighten the screws. Repeat this step 3 times.
2. Put wheel set (E, F) on assembled lower running sets as figure 2 shown. Repeat for another
wheel set.

12
G1 G2
X 2 X 2
G1 G2
1
G2
1
G1
KK
HH
G1 G2
1. Insert upper running 1 (G1) into upper running 2 (G2), then secure with screw 8 (HH) and
washer (KK) as figure shown.
Repeat for remaining upper running (G1, G2).

13
G1 G2
X 2
X 2
I1 I2
X 2
I1 I2
1
G1 G2
I1 I2
1
G1 G2
1. Insert long side guard (I1) into short side guard (I2), then fasten assembled upper running set
(G1, G2) into assembled side guard (I1, I2), align the holes of upper running set (G1, G2) and
assembled side guard (I1, I2).
Repeat for remaining long side guard (I1), short side guard (I2) and assembled upper running set
(G1, G2).

14
LX 2
L
I1
I2
G1 G2
G2
G1
1
1
1
1
L
FF FF
KK
L
1
JJ
1. Connect side guard (L) with both assembled side guard (I1, I2), secure one end section of
side guard (L) with one end section of side guard (I2) by using screw 6 (FF), washer (KK) and
bolt nut (JJ) as figure shown. Then repeat for another end section of side guard (L)
and side guard (I1).
Repeat for remaining side guard (L).
I2
I1

15
I2
G2
H2
1
I1
I2
G1
G2
1
I2
I1
H2
H1
1, Put the assembled (I1, I2, G1, G2, L) onto the assembled (H1, H2, B) as figure shown.

16
N
O
M
X 2
X 1
X 1
N
MON
NM
KK
KK
FF
FF
FF
2
2
1
1
1
2N
JJ
M
KK
O
1. Fasten the table leg (N) into the bottom of table top (M) by using screw 6 (FF) and washer (KK)
as figure 1 shown. Then secure table bracket (O) and support tube of table top (M) onto the table
leg (N) by using screw 6 (FF), washer (KK) and bolt nut (JJ) as figure 2 shown.
Repeat for other side of table leg (N), table top (O) and table bracket (O).

17
R1 R2 Q
X 2 X 2 X 6
JJ R1
R2
Q
KK
BB
KK
R2
Q
R1
Q
1
1
1
1. Connect seat 1 (R1) and seat 2 (R2) as figure shown, insert screw 2 (BB) through washer (KK)
and seat 1 (R1), plastic cap ( Q), seat 2 (R2), washer (KK), then secure with bolt nut (JJ) as
figure 1 shown.
Repeat for remaining seat 1 (R1) and seat 2 (R2).

18
S Q
X 6 X 6
Q
JJ
S
R2
R1
S
R1
EE
KK
KK
KK
S
BB
R2
R1
S
S
S
1
2
3
3
2
32
32
3
3
3
1. Insert plastic cap (Q) into the plastic sheets hole of seat bracket (S) as figure 1 shown. Then
insert screw 2 (BB) through washer (KK) and seat 1 (R1), then into plastic cap (Q) and
seat 2 (R2) secure with washer (KK) and bolt nut (JJ) as figure 2 shown. Secure both end
section of seat bracket (S) with seat 1 (R1) and seat 2 (R2) by using screw 5 (EE) and washer
(KK).
Repeat for remaining seat bracket (S) and plastic cap (Q).

19
J P
X 4 X 4
J
P
J
1
1
P
1
1
1
P
KK
II
II
J
1. Insert screw 9 (II) through washer (KK) and armrest (P) secure with arm connector (J).
Repeat for remaining armrest (P) and arm connector (J).

20
QX 8
Q
R1 R2
1
1
1
P
PJJ
Q
1
1
KK
AA
P
1. Place the assembled seat (R1, R2) onto the assembled armrest (P) as figure shown, then
insert screw 1 (AA) into washer (KK) and armrest (P) and plastic cap (Q) secure with seat 1 (R1)
and bolt nut (JJ) as figure 1 shown, then repeat this step for other side of seat 2 (R2).
Repeat for remaining assembled seat (R1, R2) and assembled armrest (P).