General assembly instructions:
vGrease all O-rings and metal securing clips
before assembly! Push an O-ring over each end
of the telescopic pipe 8/w.
Install the Valve Box [Fig. A1]:
1. Install the Valve Box 1on a bed of coarse gravel s
approx. 20 cm x 30 cm x 10 cm (V1)/
30 cm x 35 cm x 10 cm (V3).
This ensures proper drainage of the box.
2. Install the valve box with the top edge of the box at
ground level.
This avoids damage when mowing the lawn.
When installing the Valve Box, the lid must be
closed. The adjacent earth may only be carefully
compacted to prevent the walls getting pressed
in and the lid from then no longer closing com-
pletely.
If necessary, support walls from inside
with spacers when compacting earth.
Connect GARDENA connecting pipes to valve box
[Fig. A2]:
Only for Valve Box V3:
The distributor 5has 3 inputs. The Valve Box can there-
fore be connected to the watering system in various ways.
1. Screw cover caps 4onto the unused inputs.
2. Insert the distributor 5into the Valve Box from the
outside and secure to the Valve Box from the inside
using the two nuts 2
3. Screw the drain cap 6onto the distributor 5.
For Valve Box V1 and V3:
vPush the connections 7into the Valve Box from the
inside and secure to the Valve Box from the outside
using the two nuts 2.
The GARDENA Connecting Pipes 25 mm Art. 2700/
2701 and 32 mm Art. 2704 / 2705 can be connected
using the GARDENA Connectors 25 mm Art. 2762
and 32 mm Art. 2768.
V3: Connect 2 Valve Boxes V3 [Fig. A3]:
Via the 1"x1"-Connector Art. 2758-00.900.01,
2 Valve Boxes V3 can be connected.
v Screw the 1"x1"-Connector 3onto the open distributor
outputs of the two Valve Boxes V3.
V3: Close open distributor output [Fig. A4]:
If you are only installing 2 valves in a Valve Box V3, the
open distributor output must be sealed with an end cap.
1. Push the short telescopic pipe 8into the open
distributor output.
2. Insert the securing clip 9into the holes of the
distributor output 0.
The flushing pipe 8is fixed in place.
3. Screw the cover cap qonto the short telescopic
pipe 8.
Assemble the Irrigation Valve 9 V/24 V
(Art. 1251/1278) [Fig. A5]:
CAUTION!
Flow direction!
v Pay attention to the flow direction (arrows)
when assembling the Irrigation Valve e.
1. Push the long telescopic pipe wall the way into the
nipple on the outlet-side 7.
2. Screw the short telescopic pipe 8into the inlet side of
the Irrigation Valve e.
The arrows on the Irrigation Valve point in the flow
direction.
3. Push the Watering Valve with the short telescopic
pipe 8into the distributor output 0.
4. Screw the long telescopic pipe winto the outlet-side
of the Irrigation Valve e.
5. Insert the securing clip 9into the holes of the
distributor outputs 0and the connections 7.
The telescopic pipes 8
/
ware fixed in place.
When you open the box lid ryou can see the flow
direction marked by the arrows on the Irrigation
Valve e.
Connecting Watering Valves 24 V (Art. 1278)
[Fig. A6/A7]:
You can connect up to 12 Watering Valves Art. 1278
(24 V) to the Watering Controller 4040 Art. 1276 using
the Connection Cable Art. 1280 in combination with
the expansion module 2040 Art. 1277.
1. Guide the connection cable tinto the side of the
Valve Box V3 and attach to the terminal strip z
according to the outputs of the watering controller
(refer to colour of cable).
2. Screw one cable from each valve into the connections C.
3. Screw the other cable from each valve into the connec-
tions 1–6according to the routing of the cables.
4. If you are using 2 Valve Boxes of model V3, connect the
second Valve Box V3 to the first Valve Box V3 using the
connection cable.
5. Push the protective cap uover the terminal strip z
and tighten both screws i.
Please refer to the operating instructions for the
Programming Unit Art. 1242 for instructions on how
to connect the Watering Valves Art. 1251 (9 V) to
the Controllers Art. 1250.
Locking the box lid [Fig. A8]:
vLock the box lid rby turning the closing lever o90°.
The lid is then protected when the lawn is mowed.
The box lid rcan be locked to protect it against theft.
vOverlap the holes pin the Valve Box and box lid and
lock using a small padlock or locking chain
– or –
Alternatively, you can protect the lid ragainst theft
using a metal screw (4.2 x 19 mm).
10