Gardner Bender GWL-40 User manual

1
OPERATING INSTRUCTIONS
40 Watt Multi-Task LED Work Light
GWL-40
IMPORTANT: RECEIVING INSTRUCTIONS
Visually inspect all components for shipping damage. If you find damage, notify the carrier at once.
Shipping damage is NOT covered by warranty. The carrier is responsible for all repair or replacement costs resulting from damage in shipment.
WARNING SAFETY INFORMATION
1. Device will only operate at the specified voltage.
2. Repairs may only be carried out by a specialist.
3. Upon discovery of a technical error, or if there is
visible damage the light must not be put into operation.
WARNING
DRY LOCATION USE ONLY
RISK OF ELECTRIC SHOCK: Do not use extension cord near water or where
water may accumulate. Keep light at least 16 feet from pools and spas. Keep
plugs and receptacles dry. For use only on GFCI protected circuits.
TECHNICAL DATA
Input Voltage: 120V ~ 60Hz,40W
Socket Outlet: 125V ~ Max.1500W
WARNING
1. Please keep a safe distance of 0.5M. Lighted fixture gets Hot! Do not touch the lighted diode area.
The heat-dissipating aluminum surface temperature during operation may be high, which may cause burns.
2. Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void
the user's authority to operate the equipment.
WARNING
Improper use of this work light can result in injury or death. Follow all safeguards stated in this manual in addition to normal safety precautions
when working with electrical devices. DO NOT attempt to service this device. When using outdoor portable work lights, always follow basic safety
precautions to reduce the risk of fire, electric shock and personal injury.
1. Do not use the work light in the immediate vicinity of flammable materials or gases.
2. Only use accessories included with this product.
3. Do not point the light directly in your own or any other person’s or animal’s eyes.
4. If the supply cord is damaged, it must be replaced by a cord with identical specifications to avoid a hazard.
5. Keep a minimum of 20 inches (0.5m) minimum away from other light fixtures
6. Keep the lamp out of reach of children.
7. Read and follow all safety rules and operating instructions before first use of this product.
A
B
Figure 1
C
Figure 2
D
EF
Figure 3
PRODUCT FEATURES
A. ON/OFF Switch
B. Swivel Stand
C. Swivel LED Body
D. Easy Cable Storage
E. Plug
F. Socket

2
800.624.4320 • Milwaukee, WI 53151 • gardnerbender.com GAR_TL_081_0819_GWL-40
One Year Warranty limited solely to repair or replacement; no warranty of merchantability or fitness for a particular purpose. Product is warrantied
to be free of defects in materials and workmanship for the normal life of the product. In no event shall Gardner Bender be liable for
incidental or consequential damage.
CLEANING
Before cleaning, please remove the plug from the power socket. For reasons regarding electrical safety, please clean this product with a damp cloth.
Do not use any harsh cleaning agents or chemicals.
WARRANTY INFORMATION
The guarantee is not applicable for not following the instructions and improper handing of the lamp or lamps of individual part. Forcibly opening the
lamp will void the warranty! For Operating and connection errors beyond our control and resulting damages, we assume no liability.
NOTE: The external flexible cable or cord of this luminaire cannot be replaced; if the cord is damaged, the luminaire shall be destroyed.
The light source of this luminaire is not replaceable; when the light source reaches its end of life the whole luminaire shall be replaced.
Repairs may only be carried out by an authorized service centre. Original bill of purchase must be submitted.
The warranty will not apply in cases of: normal wear and tear, changes, modifications, damage caused by careless, external influences, any application
this product is not meant for or partially or completely dismantled appliances.
Surface Mounted
Luminaires not suitable for direct mounting on
normally flammable surfaces (suitable only for
mounting on non-combustible surfaces).
FCC WARNING STATEMENTS:
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
CLASS B DEVICE:
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet an a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
OPERATING INSTRUCTIONS
1. Powering the Light ON/OFF
Unwrap power cord plug, Figure 3 (E) to desired length and plug into a functioning electrical outlet. Press the On/Off Switch (A), Figure 1.
For Safety purposes, when done using the light always wrap the power cord and extension in the Easy Cable Storage (D), Figure 3.
2. Adjusting Stand & Lighting Angle
The tilting angle of the light can be adjusted as necessary by pulling the stand (B), Figure 1 and locking in place.
The lighting angle can be adjusted by lightly pulling down on the swivel LED body (C), Figure 2.
3. Mounting the Light with Magnets
The 4 heavy duty magnets on the back of the light can be used to mount the light to any metal device that is large enough and safely secured
to support the weight of the light. After the light is mounted by the magnets, be sure to double-check it securely mounted to avoid it falling
and potentially causing injury and/or damage.
4. Using Extension Cord
Unwrap extension cord connector, Figure 3 (D) to desired length and plug in secondary desired powered device (125V ~ Max.1500W).
To avoid injury or harm, be sure the secondary device is turned off or that the light On/Off switch (A) is in the OFF position so
the secondary item does not immediately power on.
Table of contents
Other Gardner Bender Work Light manuals
Popular Work Light manuals by other brands

nor-tec
nor-tec 74615 instruction manual

OEM Tools
OEM Tools 26028 Operating instructions and parts manual

SCANGRIP
SCANGRIP TOWER 5 CONNECT manual

Beta
Beta 1838AM Operation manual and instructions

Eaton
Eaton AtLite SELDWTA29SD Series installation instructions

MULTIQUIP
MULTIQUIP MLT Parts & operation manual