Garelick 31900 User manual

Assembly Instructions for
Model 31900 Motor Carrier
Form 12.123
ASSEMBLY INFORMATION
1. Check parts against parts list.
2. Read instructions completely before starting assembly.
TOOLS REQUIRED
1. Wrench adjustable to 9/16"
2. Screwdriver
3. Hammer
CAUTION: Woodblock and tubing will crush if over-
tightened.
MOTOR CARRIER ASSEMBLY
Refer to Fig. 1:
1. Slide each end of axle (A) through large holes #1 of
upright support tubes.
2. Attach woodblock (C) to top of upright support tubes by
aligning holes #2, inserting four carriage bolts (D) and
securing with fasteners (E) and (F) as illustrated (finger
tighten).
Refer to Fig. 2:
1. Insert handles (G) into SHORT ENDS of J-tubes (H).
2. Align holes #3 so that the handles will point AWAY from
each other, insert bolts (I); secure with fasteners (E) and (F)
as illustrated (finger tighten).
(over)
Parts List
Model 31900 Motor Carrier
Ref. Factory No.
Letter Part No. Req. Description
A 51.033 1 Axle
B 51.035 2 Upright support tube
C 06.318 1 Plastic Block
D 03.003 4 1⁄4-20x31⁄2" carriage bolt
E 03.118 14 1⁄4" lockwasher
F 03.023 14 1⁄4-20 nut
G 51.022 2 Handle (L&R)
H 51.032 2 J-tube
I 03.074 2 1⁄4-20x11⁄4" bolt
J 03.089 4 1⁄4-20x23⁄4" bolt
K 51.014 1 Handle brace, 25"
L 03.088 4 1⁄4-20x21⁄2" bolt
M 51.034 1 Bottom brace, 181⁄2"
O 49.096 4 Wheel
P 03.039 2 Pushnut
Q 49.003 2 Caster
R 03.022 2 3/8-16 locknut
S 06.027 2 Poly handgrip
FIG. 1 FIG. 2
Write for
a Complete
Catalog
Phone: [phone]
PO Box 8, 644 2nd Street E-mail: [email protected]
St. Paul Park, Minnesota 55071 On the Web: www.garelick.com
5/98

Refer to Fig. 3:
1. Place handle assemblies from fig. 2 on the INSIDES of
upright support tubes as illustrated. NOTE: Make certain
that handles point AWAY from each other.
2. Align holes #4, insert bolts (J); secure with fasteners (E)
and (F) as illustrated (finger tighten).
3. Align holes #5, insert bolts (J); secure with fasteners (E)
and (F) as illustrated (finger tighten).
Refer to Fig. 4:
1. Attach handle brace (K) across TOP of handles by
aligning holes #6, inserting bolts (L) and securing with
fasteners (E) and (F) as illustrated (finger tighten).
2. Attach bottom brace (M) across BOTTOM of J-tubes by
aligning holes #7, inserting bolts (L) and securing with
fasteners (E) and (F) as illustrated (finger tighten).
3. Mount two wheels (O) on each end of axle.
4. Using pushnuts (P), secure wheels by tapping them on axle
squarely with hammer.
5. Thread caster shanks (Q) through large holes #8 in J-tubes
and secure with locknuts (R) as illustrated (finger tighten).
6. Tighten all nuts and bolts on carrier.
7. Slip poly handgrips (S) on handles. NOTE: Grips go on
more easily after being heated in warm water.
8. Periodically lubricate wheels and polish* aluminum to
ensure a long life.
NOTE: Recommended for motors 30–115 H.P./315 lbs.
**EEz-In marine polish, Model 65010, available.
FIG. 3 FIG. 4
Assembly Instructions – Model 31900 Motor Carrier Form 12.123