Garmin Streetpilot C320 User manual

START HERE
StreetPilot® c320
This setup guide includes instructions
for loading maps to your c320 as well
as configuring, mounting, and using
your c320.
To ensure a successful installation,
please follow the steps outlined in
this guide. Do not connect the USB
cable to your PC or unit until you are
instructed to do so.
setup guide
190-00435-02 Rev. B

Before you begin . . .
Press and hold the
Power button to turn
on the unit.
Note: A “Low Battery”
warning may appear when
you turn on the unit. In this
case, charge the unit for three
hours by connecting it to the
enclosed AC power adapter.
Follow the setup instructions
that begin below. You cannot
begin using your unit until you
complete all of the Setup Steps.
Setup Steps:
• Configure your c320
• Install software and map data
• Load maps
1
2
Answer the configuration
questions that appear.
When you see the screen
that states “To use this
unit, map data must be
installed,” you are ready
to install software and
map data.
Configure Your c320
volume control
power button
USB cable port

Install Software and Map Data
Follow the series of instructions
that appear on your computer.
When prompted, connect your
c320 to your computer using the
enclosed USB cable.
Remove the CDs from the box
titled “Map Software.” Insert
Disk 1 into your computer.
Note: If the start-up file does not
run automatically, click the Windows
Start button and select Run…. Type
your CD-ROM’s drive followed by
“Setup” (for example, “E:\Setup”).
Click OK.
Where is my USB cable connection?
On your c320, note the location of the USB cable port as shown on the previous
panel of this Setup Guide. On your computer, look for the USB symbol
located on the back of your computer. Do not connect the USB cable to your unit
until you are instructed to do so.
1
2

When you have completed
the registration process, a
“Congratulations!” message
appears as shown at the
right. Click Done to load
maps to your c320.
Follow the instructions
on your computer to
register your c320.
If you do not register your c320 at this time, you can register it
later by inserting Disk 1 into your computer. Check Register your
StreetPilot c320 on the screen that appears. Make certain the
USB cable is connected to both your c320 and your computer.
3
4

Load Maps
Follow the instructions
given by the Map Install
Wizard on your computer.
Select the map regions
you want to load into
your c320. Then click
Next.
When your maps are successfully
loaded, click OK to close the
Map Install Wizard. Disconnect
the USB cable from your unit.
Your c320 is ready to use.
To load new maps:
Turn on your c320 and re-connect the
USB cable to your unit and PC. The Map
Install Wizard automatically appears.
Use the Map Scale to zoom
in and out of the map.
Click the directional arrows
to move the map.
Click a map region to
select it; selected map
regions are shaded pink.
Click Next to load the selected
map regions to your c320.
Storage column
The selected map regions are listed here.
1
2
3

Mount Your c320
Fit the bottom of your
c320 into the cradle of the
suction cup mount (1).
Tilt your c320 back until
it snaps in place (2).
Place the suction cup on your
windshield. Be sure the lever
is flipped toward you, as
shown to the right.
Note: To ensure a tight grip, make
certain your windshield is clean and
dry before you mount the suction
cup.
WARNING: For use in vehicles, it is the sole responsibility of the owner/operator of a vehicle with the c320 installed to
place and secure the device so it will not interfere with the vehicle operating controls and safety devices, obstruct the
driver’s view of driving conditions, or cause personal injury in the event of an accident.
NOTICE TO STATE OF CALIFORNIA DRIVERS: California Vehicle Code Section 26708 (a) (1) provides that drivers in
California should not use suction mounts on their windshield or side or rear windows. Other garmin dashboard or friction
mounting options should be used. For available accessories, refer to the garmin web site at www.garmin.com. Also, refer to
the Owner’s Manual for instructions on using the included mounting disk with the suction cup mount.
1
2
lever

3
Flip the lever back, toward
the windshield. Adjust the
c320 to obtain a maximum
viewing angle.
To remove the suction
cup from the windshield,
flip the lever toward you
to release the suction
cup’s grip. To help release
the grip, pull the rubber
tab on the suction cup
toward you.
If necessary, use the tension knob
to loosen or tighten the tension in
the mount to improve your viewing
angle.
Plug the end of the
cable into an available
power receptacle. Your
unit will turn on auto-
matically if you have
started your vehicle.
4

Touch an icon that
will help you find
your destination.
Find a Place
Touch Where to?
1
2

Enjoy the route!
Touch Go!
Touch a destination.
4
5
3

Frequently Asked Questions
How do I contact
Garmin Product
Support?
How do I register my
c320?
In the U.S.A., call 913/397.8200 or
800/800.1020, Monday–Friday, 8 AM–5 PM
Central Time; e-mail [email protected].
In Europe, call 44/0870.8501241.
How do I charge the
battery in my c320?
Can I use my c320
indoors?
Do I have an alternative
to mounting my c320
to the windshield?
If you did not register your c320 during the
initial installation, insert Disk 1 and check
Register your StreetPilot c320 on the
screen that appears.
While in your vehicle, your c320 automati-
cally charges when the cable mount is con-
nected to an available power receptacle.
When indoors, connect the enclosed AC
power adapter to your c320. Your unit also
charges when it is connected to your com-
puter with the USB cable.
You cannot receive GPS signals indoors, but
you can use the c320 in “practice” mode
when you turn off GPS. See page 20 of the
Owner’s Manual for instructions.
Yes. Attach the enclosed disk mount to
your dashboard and place the suction cup
mount on top of the disk. See page 23 of
the Owner’s Manual for additional help.