Garmin Streetpilot C320 User manual

StreetPilot® c320
quick reference guide
guide de référence rapide

© 2005 Garmin Ltd. or its subsidiaries
Garmin International, Inc.
1200 East 151st Street,
Olathe, Kansas 66062, U.S.A.
Tel. [phone]
or 800/800.1020
Fax [phone]
Garmin (Europe) Ltd.
Unit 5, The Quadrangle,
Abbey Park Industrial Estate,
Romsey, SO51 9DL, U.K.
Tel. [phone]
Fax [phone]
Garmin Corporation
No. 68, Jangshu 2nd Road,
Shijr, Taipei County, Taiwan
Tel. [phone]
Fax [phone]
All rights reserved. Except as expressly provided herein, no part of this manual may be reproduced, copied,
transmitted, disseminated, downloaded or stored in any storage medium, for any purpose without the express
prior written consent of Garmin. Garmin hereby grants permission to download a single copy of this manual
onto a hard drive or other electronic storage medium to be viewed and to print one copy of this manual or of
any revision hereto, provided that such electronic or printed copy of this manual must contain the complete
text of this copyright notice and provided further that any unauthorized commercial distribution of this manual
or any revision hereto is strictly prohibited.
Information in this document is subject to change without notice. Garmin reserves the right to change
or improve its products and to make changes in the content without obligation to notify any person or
organization of such changes or improvements. Visit the Garmin Web site (www.garmin.com) for current
updates and supplemental information concerning the use and operation of this and other Garmin products.
Garmin® and StreetPilot® are registered trademarks of Garmin Ltd. or its subsidiaries and may not be used
without the express permission of Garmin.
August 2005 Part Number 190-00435-50 Rev. A Printed in Taiwan

1
E
N
Step 1: Configure Your c320
Press and hold the Power button on the side of the unit to turn it on. Follow the on-screen
instructions to set up your c320. You only have to do this once.
Step 2: Install Software and Load Maps
Before using your c320, you need to install software on your computer using the DVD-
ROM. Then load maps on your c320. Refer to the Setup Guide for complete instructions.
Step 3: Mount Your c320
To ensure a tight grip, clean and dry your windshield.
Fit the bottom of your c320
into the cradle of the suction
cup mount.
Tilt your c320 back until
it snaps in place.
Place the suction cup on the
windshield. Flip the lever back,
toward the windshield.
Tension knob
Plug the cable into a receptacle in your vehicle. If necessary, use the tension knob to loosen
or tighten the tension in the mount to improve your viewing angle.
Your unit will turn on automatically if you have started your vehicle. To manually turn on
your c320, press and hold the Power button on the side of the unit.
WARNING: For use in vehicles, it is the sole responsibility of the owner/operator of a vehicle with the c320
installed to place and secure the device so it will not interfere with the vehicle operating controls and safety
devices, obstruct the driver’s view of driving conditions, or cause personal injury in the event of an accident.

2
E
N
Step 4: Find Your Destination
Touch Where to? Select a category. Touch the
arrows to see more categories.
Select a destination. Touch
the arrows to see more places.
Touch . Enjoy the route!

3
E
N
Step 5: Follow Your Route
Follow the route to your destination using the Map page. As you travel, your c320 guides
you to your destination with voice prompts, arrows on the map, and directions at the top of
the Map page. If you depart from the original route, your c320 voice announces that you are
off-route and then provides new route instructions.
Your route is marked with
a red line.
Follow the arrows as you
take turns.
A checkered flag marks
your destination.
Read the driving instructions at the top of the page.

4
E
N
Viewing the Map Page
From the Menu page, touch View map to open the Map page.
The position icon shows your current location. Touch
buttons on the Map page to see additional information.
Trip Information Page Current Route Page Next Turn Page
Map Page while Navigating a Route
Touch Arrival or
Speed to open the
Trip Information page.
Touch Turn In to open
the Next Turn page.
Touch the text bar
to open the Current
Route page.
Touch to zoom out.
Touch to zoom in.
Touch Menu to return
to the Menu page.

5
E
N
Saving Places You Find
After you have found a place,
touch Save.
Touch OK in the pop-up window. The place
is saved in My Locations > Favorites.
Finding Saved Places
Touch .
From the Menu page,
touch Where to? > My
Locations > Favorites.
Select a place.

6
E
N
Setting a Home Location
Touch Set Home.
Touch My Locations.Touch Where to?
Select an option.
Going Home
After you have set your Home location, you can route to it at any time by touching My
Locations and then Go Home.
Changing Your Home Location
Change your Home location by repeating the steps you took to set it.

7
E
N
Adjusting the Backlight Brightness
Touch the minus (-) lightbulb to decrease the backlight brightness or the plus (+) lightbulb to
increase the brightness. When you are finished, touch OK.
Adjusting the Volume
To adjust the volume, turn the Volume knob,
located above the Power button.
Turning the c320 On and Off
Press and hold the Power button on the
side of the unit to turn it on and off.
More Information
See the Owner’s Manual located on the
DVD-ROM for more information.
Volume
knob
Power
button
USB
cable
connector

8
F
R
Etape 1 : Configuration de votre navigateur c320
Appuyez sur le bouton d’Alimentation situé sur le côté de l’appareil et maintenez-le
enfoncé pour mettre votre navigateur sous tension et l’arrêter. Lorsque que vous mettez
votre appareil en marche pour la première fois, suivez les informations affichées à l’écran
pour procéder à l’installation de votre navigateur c320. Vous ne devrez accomplir cette étape
qu’une seule fois.
Etape 2 : Installation des logiciels et chargement des cartes
Avant d’utiliser votre navigateur c320, vous devez installer les logiciels adéquats sur votre
ordinateur depuis le DVD-ROM fourni, puis charger les cartes requises sur votre navigateur
c320. Reportez-vous au guide de configuration pour obtenir des instructions exhaustives.
Etape 3 : Installation de votre navigateur c320
Afin de garantir une adhérence maximale, nettoyez et séchez soigneusement votre pare-brise
avant d’installer la ventouse.
Insérez la base de votre
navigateur c320 dans le
logement du support à
ventouse.
Inclinez votre navigateur
c320 vers l’arrière
jusqu’à ce qu’il
s’enclenche.
Positionnez la ventouse sur votre
pare-brise. Faites basculer le
levier vers l’arrière, en direction du
pare-brise.
Bouton de réglage de tension