Garmin Streetpilot C320 User manual

Continued from Step 3....
Plug the cable into a receptacle in your vehicle. If necessary, use the tension knob to
loosen or tighten the tension in the mount to improve your viewing angle.
Your unit will turn on automatically if you have started your vehicle. To manually
turn on your c320, press and hold the Power button on the side of the unit. Refer
to the image on the back of this sheet.
Step 4: Find Your Destination
Select a category. Touch the
arrows to see more categories.
Touch Where to?
Touch . Enjoy the route!
Select a destination. Touch
the arrows to see more places.
Step 1: Configure Your c320
Press and hold the Power button on the side of the unit to turn it on. Follow the
on-screen instructions to set up your c320; you only have to do this once.
Step 2: Install Software and Load Maps
Before using your c320, you need to install software on your computer using the
DVD-ROM and then load maps on your c320. Refer to the Setup Guide for complete
instructions.
Step 3: Mount Your c320
To ensure a tight grip, clean and dry your windshield before you mount the suction
cup.
Fit the bottom of your c320
into the cradle of the suction
cup mount.
Tilt your c320 back until
it snaps in place.
Place the suction cup on the
windshield. Flip the lever back,
toward the windshield.
Tension knob
Continued on the top of the next column....
Step 5: Follow Your Route
Follow the route to your destination using the Map page. As you travel, your
c320 guides you to your destination with voice prompts, arrows on the map, and
directions at the top of the Map page. If you depart from the original route, your
c320 recalculates the route and provides new route instructions.
Your route is marked with
a red line.
Follow the arrows as you
take turns.
A checkered flag marks
your destination.
Read the driving instructions at the top of the page.
StreetPilot® c320
quick reference guide
WARNING: For use in vehicles, it is the sole responsibility of the owner/operator of a vehicle with the c320 installed to place and secure the
device so it will not interfere with the vehicle operating controls and safety devices, obstruct the driver’s view of driving conditions, or cause
personal injury in the event of an accident.
NOTICE TO STATE OF CALIFORNIA DRIVERS: California Vehicle Code Section 26708 (a) (1) provides that drivers in California should
not use suction mounts on their windshield or side or rear windows. Other Garmin dashboard or friction mounting options should be used. For
available accessories, refer to the Garmin Web site at www.garmin.com. Also, refer to the Owner’s Manual for instructions on using the included
mounting disk with the suction cup mount.

Continued from Step 3....
Plug the cable into a receptacle in your vehicle. If necessary, use the tension knob to
loosen or tighten the tension in the mount to improve your viewing angle.
Your unit will turn on automatically if you have started your vehicle. To manually
turn on your c320, press and hold the Power button on the side of the unit. Refer
to the image on the back of this sheet.
Step 4: Find Your Destination
Select a category. Touch the
arrows to see more categories.
Touch Where to?
Touch . Enjoy the route!
Select a destination. Touch
the arrows to see more places.
Step 1: Configure Your c320
Press and hold the Power button on the side of the unit to turn it on. Follow the
on-screen instructions to set up your c320; you only have to do this once.
Step 2: Install Software and Load Maps
Before using your c320, you need to install software on your computer using the
DVD-ROM and then load maps on your c320. Refer to the Setup Guide for complete
instructions.
Step 3: Mount Your c320
To ensure a tight grip, clean and dry your windshield before you mount the suction
cup.
Fit the bottom of your c320
into the cradle of the suction
cup mount.
Tilt your c320 back until
it snaps in place.
Place the suction cup on the
windshield. Flip the lever back,
toward the windshield.
Tension knob
Continued on the top of the next column....
Step 5: Follow Your Route
Follow the route to your destination using the Map page. As you travel, your
c320 guides you to your destination with voice prompts, arrows on the map, and
directions at the top of the Map page. If you depart from the original route, your
c320 recalculates the route and provides new route instructions.
Your route is marked with
a red line.
Follow the arrows as you
take turns.
A checkered flag marks
your destination.
Read the driving instructions at the top of the page.
StreetPilot® c320
quick reference guide
WARNING: For use in vehicles, it is the sole responsibility of the owner/operator of a vehicle with the c320 installed to place and secure the
device so it will not interfere with the vehicle operating controls and safety devices, obstruct the driver’s view of driving conditions, or cause
personal injury in the event of an accident.
NOTICE TO STATE OF CALIFORNIA DRIVERS: California Vehicle Code Section 26708 (a) (1) provides that drivers in California should
not use suction mounts on their windshield or side or rear windows. Other Garmin dashboard or friction mounting options should be used. For
available accessories, refer to the Garmin Web site at www.garmin.com. Also, refer to the Owner’s Manual for instructions on using the included
mounting disk with the suction cup mount.

Continued from Step 3....
Plug the cable into a receptacle in your vehicle. If necessary, use the tension knob to
loosen or tighten the tension in the mount to improve your viewing angle.
Your unit will turn on automatically if you have started your vehicle. To manually
turn on your c320, press and hold the Power button on the side of the unit. Refer
to the image on the back of this sheet.
Step 4: Find Your Destination
Select a category. Touch the
arrows to see more categories.
Touch Where to?
Touch . Enjoy the route!
Select a destination. Touch
the arrows to see more places.
Step 1: Configure Your c320
Press and hold the Power button on the side of the unit to turn it on. Follow the
on-screen instructions to set up your c320; you only have to do this once.
Step 2: Install Software and Load Maps
Before using your c320, you need to install software on your computer using the
DVD-ROM and then load maps on your c320. Refer to the Setup Guide for complete
instructions.
Step 3: Mount Your c320
To ensure a tight grip, clean and dry your windshield before you mount the suction
cup.
Fit the bottom of your c320
into the cradle of the suction
cup mount.
Tilt your c320 back until
it snaps in place.
Place the suction cup on the
windshield. Flip the lever back,
toward the windshield.
Tension knob
Continued on the top of the next column....
Step 5: Follow Your Route
Follow the route to your destination using the Map page. As you travel, your
c320 guides you to your destination with voice prompts, arrows on the map, and
directions at the top of the Map page. If you depart from the original route, your
c320 recalculates the route and provides new route instructions.
Your route is marked with
a red line.
Follow the arrows as you
take turns.
A checkered flag marks
your destination.
Read the driving instructions at the top of the page.
StreetPilot® c320
quick reference guide
WARNING: For use in vehicles, it is the sole responsibility of the owner/operator of a vehicle with the c320 installed to place and secure the
device so it will not interfere with the vehicle operating controls and safety devices, obstruct the driver’s view of driving conditions, or cause
personal injury in the event of an accident.
NOTICE TO STATE OF CALIFORNIA DRIVERS: California Vehicle Code Section 26708 (a) (1) provides that drivers in California should
not use suction mounts on their windshield or side or rear windows. Other Garmin dashboard or friction mounting options should be used. For
available accessories, refer to the Garmin Web site at www.garmin.com. Also, refer to the Owner’s Manual for instructions on using the included
mounting disk with the suction cup mount.

Continued from Step 3....
Plug the cable into a receptacle in your vehicle. If necessary, use the tension knob to
loosen or tighten the tension in the mount to improve your viewing angle.
Your unit will turn on automatically if you have started your vehicle. To manually
turn on your c320, press and hold the Power button on the side of the unit. Refer
to the image on the back of this sheet.
Step 4: Find Your Destination
Select a category. Touch the
arrows to see more categories.
Touch Where to?
Touch . Enjoy the route!
Select a destination. Touch
the arrows to see more places.
Step 1: Configure Your c320
Press and hold the Power button on the side of the unit to turn it on. Follow the
on-screen instructions to set up your c320; you only have to do this once.
Step 2: Install Software and Load Maps
Before using your c320, you need to install software on your computer using the
DVD-ROM and then load maps on your c320. Refer to the Setup Guide for complete
instructions.
Step 3: Mount Your c320
To ensure a tight grip, clean and dry your windshield before you mount the suction
cup.
Fit the bottom of your c320
into the cradle of the suction
cup mount.
Tilt your c320 back until
it snaps in place.
Place the suction cup on the
windshield. Flip the lever back,
toward the windshield.
Tension knob
Continued on the top of the next column....
Step 5: Follow Your Route
Follow the route to your destination using the Map page. As you travel, your
c320 guides you to your destination with voice prompts, arrows on the map, and
directions at the top of the Map page. If you depart from the original route, your
c320 recalculates the route and provides new route instructions.
Your route is marked with
a red line.
Follow the arrows as you
take turns.
A checkered flag marks
your destination.
Read the driving instructions at the top of the page.
StreetPilot® c320
quick reference guide
WARNING: For use in vehicles, it is the sole responsibility of the owner/operator of a vehicle with the c320 installed to place and secure the
device so it will not interfere with the vehicle operating controls and safety devices, obstruct the driver’s view of driving conditions, or cause
personal injury in the event of an accident.
NOTICE TO STATE OF CALIFORNIA DRIVERS: California Vehicle Code Section 26708 (a) (1) provides that drivers in California should
not use suction mounts on their windshield or side or rear windows. Other Garmin dashboard or friction mounting options should be used. For
available accessories, refer to the Garmin Web site at www.garmin.com. Also, refer to the Owner’s Manual for instructions on using the included
mounting disk with the suction cup mount.

Adjusting the Backlight Brightness
From the Menu page, touch
the brightness button
to adjust the level of the
backlight. Touch the minus
(-) lightbulb to decrease the
backlight brightness or the
plus (+) lightbulb to increase
the brightness. When you are
finished, touch OK.
Adjusting the Volume
To adjust the volume, turn the Volume
knob, located above the Power button.
Turning the c320 On and Off
Press and hold the Power button on
the side of the unit to turn it on and off.
More Information
For more information about your c320, refer to the Owner’s Manual located at
http://www.garmin.com/products/sp320/. Click on the Manuals link and then select
Download.
Saving Places You Find
After you have found a place
you want to save, touch Save.
Touch OK in the pop-up window. The place
is saved in My Locations > Favorites.
Finding Saved Places
Touch .
From the Menu page,
touch Where to? > My
Locations > Favorites.
Select a place.
Setting a Home Location
Touch Set Home.
Touch Where to?
Select an option.
Touch My Locations.
Going Home
After you have set your Home location, you can route to it at any time by touching
My Locations and then Go Home.
Changing Your Home Location
Change your Home location by repeating the steps you took to set it.
Viewing the Map Page
From the Menu page, touch View map to open the
Map page. The position icon shows your current
location. Touch buttons on the Map page to see additional
information.
© Copyright 2005 Garmin Ltd. or its subsidiaries
June 2005 1 90-00435-01 Rev. A Printed in Taiwan
Trip Information Page Current Route Page Next Turn Page
Map Page while Navigating a Route
Touch Arrival or
Speed to open the Trip
Information page.
Touch Turn In to open
the Next Turn page.
Touch the text bar to
open the Current Route
page.
Touch to zoom out.
Touch to zoom in.
Touch Menu to return
to the Menu page.
Volume
knob
Power
button
USB cable
connector

Adjusting the Backlight Brightness
From the Menu page, touch
the brightness button
to adjust the level of the
backlight. Touch the minus
(-) lightbulb to decrease the
backlight brightness or the
plus (+) lightbulb to increase
the brightness. When you are
finished, touch OK.
Adjusting the Volume
To adjust the volume, turn the Volume
knob, located above the Power button.
Turning the c320 On and Off
Press and hold the Power button on
the side of the unit to turn it on and off.
More Information
For more information about your c320, refer to the Owner’s Manual located at
http://www.garmin.com/products/sp320/. Click on the Manuals link and then select
Download.
Saving Places You Find
After you have found a place
you want to save, touch Save.
Touch OK in the pop-up window. The place
is saved in My Locations > Favorites.
Finding Saved Places
Touch .
From the Menu page,
touch Where to? > My
Locations > Favorites.
Select a place.
Setting a Home Location
Touch Set Home.
Touch Where to?
Select an option.
Touch My Locations.
Going Home
After you have set your Home location, you can route to it at any time by touching
My Locations and then Go Home.
Changing Your Home Location
Change your Home location by repeating the steps you took to set it.
Viewing the Map Page
From the Menu page, touch View map to open the
Map page. The position icon shows your current
location. Touch buttons on the Map page to see additional
information.
© Copyright 2005 Garmin Ltd. or its subsidiaries
June 2005 1 90-00435-01 Rev. A Printed in Taiwan
Trip Information Page Current Route Page Next Turn Page
Map Page while Navigating a Route
Touch Arrival or
Speed to open the Trip
Information page.
Touch Turn In to open
the Next Turn page.
Touch the text bar to
open the Current Route
page.
Touch to zoom out.
Touch to zoom in.
Touch Menu to return
to the Menu page.
Volume
knob
Power
button
USB cable
connector

Adjusting the Backlight Brightness
From the Menu page, touch
the brightness button
to adjust the level of the
backlight. Touch the minus
(-) lightbulb to decrease the
backlight brightness or the
plus (+) lightbulb to increase
the brightness. When you are
finished, touch OK.
Adjusting the Volume
To adjust the volume, turn the Volume
knob, located above the Power button.
Turning the c320 On and Off
Press and hold the Power button on
the side of the unit to turn it on and off.
More Information
For more information about your c320, refer to the Owner’s Manual located at
http://www.garmin.com/products/sp320/. Click on the Manuals link and then select
Download.
Saving Places You Find
After you have found a place
you want to save, touch Save.
Touch OK in the pop-up window. The place
is saved in My Locations > Favorites.
Finding Saved Places
Touch .
From the Menu page,
touch Where to? > My
Locations > Favorites.
Select a place.
Setting a Home Location
Touch Set Home.
Touch Where to?
Select an option.
Touch My Locations.
Going Home
After you have set your Home location, you can route to it at any time by touching
My Locations and then Go Home.
Changing Your Home Location
Change your Home location by repeating the steps you took to set it.
Viewing the Map Page
From the Menu page, touch View map to open the
Map page. The position icon shows your current
location. Touch buttons on the Map page to see additional
information.
© Copyright 2005 Garmin Ltd. or its subsidiaries
June 2005 1 90-00435-01 Rev. A Printed in Taiwan
Trip Information Page Current Route Page Next Turn Page
Map Page while Navigating a Route
Touch Arrival or
Speed to open the Trip
Information page.
Touch Turn In to open
the Next Turn page.
Touch the text bar to
open the Current Route
page.
Touch to zoom out.
Touch to zoom in.
Touch Menu to return
to the Menu page.
Volume
knob
Power
button
USB cable
connector

Adjusting the Backlight Brightness
From the Menu page, touch
the brightness button
to adjust the level of the
backlight. Touch the minus
(-) lightbulb to decrease the
backlight brightness or the
plus (+) lightbulb to increase
the brightness. When you are
finished, touch OK.
Adjusting the Volume
To adjust the volume, turn the Volume
knob, located above the Power button.
Turning the c320 On and Off
Press and hold the Power button on
the side of the unit to turn it on and off.
More Information
For more information about your c320, refer to the Owner’s Manual located at
http://www.garmin.com/products/sp320/. Click on the Manuals link and then select
Download.
Saving Places You Find
After you have found a place
you want to save, touch Save.
Touch OK in the pop-up window. The place
is saved in My Locations > Favorites.
Finding Saved Places
Touch .
From the Menu page,
touch Where to? > My
Locations > Favorites.
Select a place.
Setting a Home Location
Touch Set Home.
Touch Where to?
Select an option.
Touch My Locations.
Going Home
After you have set your Home location, you can route to it at any time by touching
My Locations and then Go Home.
Changing Your Home Location
Change your Home location by repeating the steps you took to set it.
Viewing the Map Page
From the Menu page, touch View map to open the
Map page. The position icon shows your current
location. Touch buttons on the Map page to see additional
information.
© Copyright 2005 Garmin Ltd. or its subsidiaries
June 2005 1 90-00435-01 Rev. A Printed in Taiwan
Trip Information Page Current Route Page Next Turn Page
Map Page while Navigating a Route
Touch Arrival or
Speed to open the Trip
Information page.
Touch Turn In to open
the Next Turn page.
Touch the text bar to
open the Current Route
page.
Touch to zoom out.
Touch to zoom in.
Touch Menu to return
to the Menu page.
Volume
knob
Power
button
USB cable
connector