GarrettCom Magnum 10ETS User manual
www GarrettCom com
..
www GarrettCom com
..
Corporate Headquarters
GarrettCom, Inc.
47823 Westinghouse Dr.
Fremont, CA 94539-7437
Phone (510) 438-9071
Fax (510) 438-9072
Website: http://www.GarrettCom.com
Email: [email protected]
Magnum 10ETS
Ethernet Terminal Server
Magnum 10XTS
Router Terminal Server
Hardware
Installation and User Guide
Magnum 10ETS / 10XTS Installation and User Guide 06/12
i
www GarrettCom com
..
Magnum™10ETS / 10XTS
Terminal Servers
Hardware
Installation and User Guide
Part #: 84-00191Z (Rev. C)
Trademarks
GarrettCom is a registered trademark and Magnum, Dymec, DynaStar, Personal
Switch, Link-Loss-Learn, S-Ring, Convenient Switch and Converter Switch
are trademarks of GarrettCom, Inc.
Ethernet is a trademark of Xerox Corporation
NEBS is a trademark of Telcordia Technologies
UL is a registered trademark of Underwriters Laboratories
Important: The Magnum 10ETS/10XTS Terminal Server contains no user-
serviceable parts. Attempted service by unauthorized personnel may render all
warranties null and void. If problems are experienced with a Magnum 10ETS or
10XTS product, consult Section 6, Troubleshooting.
Copyright ©2012 GarrettCom, Inc. All rights reserved. No part of this publication may
be reproduced without prior written permission from GarrettCom, Inc.
Printed in the United States of America
GarrettCom, Inc. reserves the right to change specifications, performance characteristics
and/or model offerings without notice.
Warranty:
Refer to current Belden Americas Terms & Conditions for warranty information.
Contacting GarrettCom, Inc
Please use the mailing address, phone and fax numbers and email address listed below:
GarrettCom, Inc.
47823 Westinghouse Dr.
Fremont, CA 94539-7437
Phone (510) 438-9071
Fax (510) 438-9072
Website: http://www.GarrettCom.com
Email: [email protected]
Magnum 10ETS / 10XTS Installation and User Guide 06/12
ii
www GarrettCom com
..
Compliance Statements
FCC Part 15
This equipment generates uses and can radiate frequency energy and if not
installed and used properly in strict accordance with the manufacturer's instructions, may
cause interference to radio communication. It has been tested and found to comply with
the limits for a Class A computing device in accordance with the specifications in
Subpart J of Part 15 of FCC rules, which are designed to provide reasonable protection
against such interference when operated in a commercial environment. Operation of this
equipment in a residential area is likely to cause interference, in which case the user, at
their own expense, will be required to take whatever measures may be required to correct
the interference.
FCC Part 68
This device complies with part 68 of the FCC rules and the requirements
adopted by the ACTA. On the bottom of this equipment is a label that contains, among
other information, a product identifier in the format US:AAAEQ##TXXXX. If requested,
this number must be provided to the telephone company.
Note: REN (Ringer Equivalence Number) does not apply to this equipment.
IC CS03 (Industry Canada)
This digital apparatus does not exceed the Class A limits for radio noise
emissions from digital apparatus set out in the interference-causing equipment entitled
“Digital Apparatus”, ICES-003 of the department of Communications (Cet appareil
numérique respecte les limites bruits radioélectriques applicables aux appareils
numériques de Class A prescrites dans la norme sur le materiel brouilleur: “Appareils
Numériques”, NMB-003 édictée par le ministre des Communications).
This product meets the applicable Industry Canada technical specifications/Le présent
materiel est conforme aux specifications techniques applicables d’Industrie Canada.
Magnum 10ETS / 10XTS Installation and User Guide 06/12
iii
www GarrettCom com
..
Complies with FDA radiation performance
standards, 21CFR Subchapter J.
Electrical Safety requirements:
1. This product is to be installed Only in Restricted Access Areas
(Dedicated Equipment Rooms, Electrical Closets, or the like).
2. All products shall be installed with a readily accessible disconnect device in
the building installation supply circuit to the product.
3. This product shall be provided with a maximum 10A DC Listed fuse or
circuit breaker in the supply circuit when connected to a 48V
centralized source.
4. The external power supply for DC units shall be Listed, Direct Plug In
power unit, marked Class 2, or listed ITE Power Supply, marked LPS,
which has suitably rated output voltage (i.e. 24VDC or 48VDC) and suitable
rated output current.
5. Product does not contain user replaceable fuses. Any internal fuses can
ONLY be replaced by GarrettCom personnel through the RMA process.
6. The chassis main earthing screw shall be connected to the supply protective
earthing conductor.
This equipment has the ordering option of being supplied to the purchaser without a
Fiber Optic Class 1 Laser transceiver included. In this case, it is the responsibility of the
purchasing party to apply the proper labeling required to the product, in accordance
with US 21CFR Subchapter J Part 1040, if a transceiver is installed by the purchaser.
(See label example below)
Magnum 10ETS / 10XTS Installation and User Guide 06/12
iv
www GarrettCom com
..
Table of Contents Page
1.0SPECIFICATIONS...................................................................................1
1.1Technical Specifications .........................................................................1
1.2Ordering Information..............................................................................4
2.0INTRODUCTION...................................................................................10
2.1Inspecting the Package and Product......................................................10
2.2 Product Description...............................................................................11
2.3Managed Network Software for Magnum 10ETS/XTS........................12
2.4Features and Benefits............................................................................13
3.0INSTALLATION...................................................................................15
3.1Locating Magnum 10ETS/XTS Terminal Servers................................15
3.2Connecting Network Cables .................................................................16
3.2.1Connecting Shielded Twisted Pair (CAT3, CAT5).......................16
3.2.2Connecting Singlemode Fiber Optic.............................................17
3.2.3SFP (Small Form-factor Pluggable) Transceivers.........................17
3.2.4Connecting Fiber Optic Cable to SFP Transceivers......................18
3.2.5Connecting DB9 Serial ports.........................................................18
3.3Mounting...............................................................................................19
3.3.1Rack-mounting options.................................................................19
3.3.2Rack-mounting, Reverse mount option.........................................19
3.4Powering the Magnum 10ETS/XTS Terminal Server ..........................22
3.4.1Power Input connection.................................................................22
3.5Alarm Contacts for monitoring internal power, and Software Traps....23
3.6Connecting the Console Terminal.........................................................25
3.6.1RJ45 Console port pin assignments ..............................................25
3.7Module pin assignments........................................................................26
4.0OPERATION ..........................................................................................32
4.1Switching Functionality........................................................................32
4.2Auto-Cross (MDIX) and Auto-negotiation, for Ethernet RJ45 ports...33
4.3Packet Prioritization, 802.1p QOS........................................................34
4.4Frame Buffering....................................................................................34
4.5Flow-control, IEEE 802.3x standard.....................................................35
4.6Power Budget Calculations for Modules with Fiber Media..................36
5.0MAGNUM 10ETS/XTS TERMINAL SERVER PORT MODULES.36
5.110ETS/XTS Modules............................................................................36
5.1.110ETS/XTS Module LED designations........................................37
5.1.210TS2-RJ45, two 10/100Mb RJ45 ports (use in Slots A / B).......38
5.1.310TS2-HSFP, two 100Mb open SFP ports (use in Slots A / B)....38
5.1.4IRIGB-TMODULE, two BNC connectors (use in Slot B) ...........38
5.1.5 10K4-RJ45, four 10/100Mb RJ45 ports (use in Slot C)................39
5.1.6 10K4PX-RJ45, four 10/100Mb PoE+ RJ45 ports (use in Slot C).39
5.1.7 10K4-MLC, four Multimode LC (use in Slot C) ..........................40
5.1.810K4-SLC, 10K4-SLCL, four Singlemode LC (use in Slot C) ....40
Magnum 10ETS / 10XTS Installation and User Guide 06/12
v
www GarrettCom com
..
5.1.910K4-MTRJ, four Multimode MTRJ (use in Slot C)....................41
5.1.1010K2-MSC, 10K2-MST (use in Slot C)........................................41
5.1.1110K2-SSC, 10K2-SSCL (use in Slot C)........................................42
5.1.1210K4-FXSFP, four open 100Mb SFP slots (use in Slot C)...........42
5.1.1310K2-F10ST, Two 10Mb ST Multimode (use in Slot C) .............42
5.1.1410TS2-DB9, DB-9 Serial module (use in Slots C-J).....................43
5.1.1510TS4-RJ45, RJ45 Serial module (use in Slots C-J).....................43
5.1.1610-2T1E1, Dual T1/E1 WAN adapter (use in Slot I only)............44
6.0TROUBLESHOOTING .........................................................................44
6.1Before Calling for Assistance ...............................................................44
6.2When Calling for Assistance.................................................................45
6.3Return Material Authorization (RMA) Procedure ................................45
6.4Shipping and Packaging Information....................................................46
APPENDIX A: DC Power Input........................................................................47
APPENDIX B: Removal / Installation of the Hot-Swap power supply..........49
Revisions:
Rev. A 06/12: Initial Release
Rev. B 07/12: added 10XTS
Rev. C 10/12: updated 10TS2-DB9 modules
Magnum 10ETS / 10XTS Installation and User Guide 06/12
1
www GarrettCom com
..
1.0 SPECIFICATIONS
1.1 Technical Specifications
Serial Protocols:
Async to TCP/IP – including Modbus gateway for connectivity to serial
Modbus devices and to other Modbus Ethernet devices
TCP/IP to serial/reverse terminal server, Serial Multipoint & Multimaster
Topologies
PPP with authentication
Performance:
Serial DB9 Ports: RS232 only or RS232/RS485/RS422 software selectable
DB9 interface. Serial data rate from 300 bps to 230.4 kbps.
Data length - 1-32 bits
Serial RJ45 Ports: Same functionality as DB-9 ports (RJ45 pinout conforms
to EIA-561 DTE standard)
RJ45 Ports: 100 or 10 Mb speed, full- or half-duplex mode, per port,
individually determined.10/100 auto-negotiating & auto-cross
Fiber Ports, 100 Mb (multi-mode and single-mode):
Configurable in modules. at 2 per module, or SFF (Small Form Factor) for
high fiber port density, 4 per module. Each FDX or HDX,
default is FDX mode.
WAN Ports: T1/E1: 1.544 Mbps / 2.048 Mbps G.703
Network Standards and Compliance, hardware:
Ethernet V1.0/V2.0 IEEE 802.3: 10BASE-T,
IEEE 802.3u: 100Base-TX, 100BASE-FX, Auto-negotiation on TP
IEEE 802.1p: Priority protocol
IEEE 802.1d: Spanning Tree protocol
IEEE 802.1w: Rapid Spanning Tree protocol
IEEE 802.1q: VLAN Tagging, maximum 32 VLANs
IEEE 802.3x: Flow Control
Maximum 10 Mbps Ethernet Segment Lengths:
Shielded twisted pair - 150 m (492 ft)
10BASE-FL multimode fiber optic - 2 km (6562 ft)
Maximum Standard Fast Ethernet Segment Lengths:
10BASE-T (CAT 3, 4, 5 UTP) - 100 m (328 ft)
100BASE-TX (CAT 5 UTP) - 100 m (328 ft)
Shielded twisted pair - 150 m (492 ft)
100BASE-FX, half-duplex, multimode - 412 m (1350 ft)
100BASE-FX, full-duplex, multimode- 2.0 km (6562 ft)
100BASE-FX, half-duplex, singlemode - 412 m (1350 ft)
100BASE-FX, full-duplex, singlemode - 20.0 km (66K ft)
100BASE-FX, full-duplex, Long Reach - 40.0 km (122K ft)
Magnum 10ETS / 10XTS Installation and User Guide 06/12
2
www GarrettCom com
..
Fiber Multimode connector types supported:
Fiber Port, LC-type (plug-in): SFF/SFP fiber multimode 100BASE-FX
Fiber Port, MTRJ-type (plug-in): SFF fiber multimode 100BASE-FX
Fiber Port, SC-type (plug-in), multimode 100BASE-FX
Fiber Port, ST-type (twist-lock), multimode 100BASE-FX
Fiber Singlemode connector types:
Fiber Port, LC-type, Fiber SFF/SFP singlemode, 100BASE-FX
Fiber Port, SC-type, singlemode, 100BASE-FX
Serial LEDs: Per DB-9 or RJ45 port
(see section 5.1.1 for detailed LED configurations)
One LED/port indicating active connection
Ethernet LEDs: Per RJ45 or Fiber port
(see section 5.1.1 for detailed LED configurations)
One LED/port indicating LINK (solid green) and ACTIVITY (blinking)
Operating Environment:
Ambient Temperature:
-40°to 140°F (-40°to 60°C) for UL 60950 Component Parts rating
-40°to 185°F (-40°to 85°C) for IEC 60068 Type Test short term rating
Storage Temperature: -40°to 185°F (-40°to 85°C)
Ambient Relative Humidity: 5% to 95% (non-condensing)
Altitude: -200 to 13,000 ft. (-60 to 4000m)
Conformal Coating (humidity protection) optional: Request quote
Alarm Relay Contacts:
Form C, One NC indicating internal power, one NC software controllable
10ETSP / 10XTSP (PoE chassis): One Form C, NC/NO software controllable
Mechanical:
Enclosure: High strength steel, 1U rack-mounting or stand-alone
Dimensions: 1.74 in H x 17.5 in W x 12.0 in D
(4.4 cm H x 44.5 cm W x 30.5 cm D)
Cooling method: Convection, special (patent pending) thermal techniques
Weight: 10.6 lbs. (4.8 kg)
Magnum 10ETS / 10XTS Installation and User Guide 06/12
3
www GarrettCom com
..
DC Power Supply (Internal, floating ground)
DC Power Connector: Terminal block
(L) 24/48VDC Power Input (range 22 to 60VDC)
for PoE applications:
PoE+ 802.3at: (L) 48VDC Power Input (range 52 to 56VDC)
(H) AC/DC Power Input (range 90-250V AC or DC)
Standard 3-screw Terminal Block: “ -, +, GND ”
Power Consumption:
20 watts Max. (for a fully populated unit)
AC Power Supply (Internal)
AC Power Connector: IEC-320/C14 type, male recessed
100-240VAC Power Input, 47 to 63 Hz (auto-ranging)
Management Console Connector
RJ45, see details at Section 3.6
Mounting:
Rack-mounting, normal method.
Unit supplied with rack-mounting brackets for mounting in a 19” rack.
Agency Approvals and Standards Compliance:
UL listed (UL60950), cUL, CE
Emissions (EN55022) meet FCC Part 15 Class A
IEEE 1613 Class 2 Environmental Standard for Electric Power Substations
See also Note for Power Substations in Section 3.2.1 and 5.1.5
IEC 61850-3 EMC and Operating Conditions Class C for Power Substations
NEMA TS-2 for Traffic Control
EN50155 for Railways
Warranty: Refer to current Belden Americas Terms & Conditions for
warranty information.
Email
Magnum 10ETS / 10XTS Installation and User Guide 06/12
4
www GarrettCom com
..
1.2 Ordering Information
10ETS Ethernet Terminal Server - w/Hot Swap power supplies
MODEL DESCRIPTION
10ETS-HSPHH: Magnum 10ETS Terminal Server, front-mount, with two PS
slots for two (H) Hot-Swap Power Supplies. May be factory-configured with a variety
of Ethernet fiber and copper port modules and Serial port modules designed
specifically for the 10ETS/XTS. Configure up to 36 ports in a mix of Ethernet and
Serial port combinations.
10ETSR-HSPHH: Same as Model 10ETS-HSPHH except chassis is a Reverse
Mount unit. (All signal and power cables are in the rear).
10ETS-HSPHL: Magnum 10ETS Terminal Server, front-mount, with two PS
slots for one (H) and one (L) Hot-Swap Power Supply. May be factory-configured
with a variety of Ethernet fiber and copper port modules and Serial port modules
designed specifically for the 10ETS/XTS. Configure up to 36 ports in a mix of
Ethernet and Serial port combinations.
10ETSR-HSPHL: Same as Model 10ETS-HSPHL except chassis is a Reverse
Mount unit. (All signal and power cables are in the rear).
10ETS-HSPLL: Magnum 10ETS Terminal Server, front-mount, with two PS
slots for two (L) Hot-Swap Power Supplies. May be factory-configured with a variety
of Ethernet fiber and copper port modules and Serial port modules designed
specifically for the 10ETS/XTS. Configure up to 36 ports in a mix of Ethernet and
Serial port combinations.
10ETSR-HSPLL: Same as Model 10ETS-HSPLL except chassis is a Reverse
Mount unit. (All signal and power cables are in the rear).
10ETSP-HSPLL: Magnum 10ETS Terminal Server, front-mount, with two PS
slots for two (L) Hot-Swap Power Supplies. May be factory-configured with a variety
of Ethernet fiber and copper port modules and Serial port modules designed
specifically for the 10ETS/XTS. Configure up to 36 ports in a mix of Ethernet and
Serial port combinations. Supports PoE
10ETSPR-HSPLL: Same as Model 10ETSP-HSPLL except chassis is a Reverse
Mount unit. (All signal and power cables are in the rear). Supports PoE
Magnum 10ETS / 10XTS Installation and User Guide 06/12
5
www GarrettCom com
..
10ETS Ethernet Terminal Server - w/Fixed power supplies
MODEL DESCRIPTION
10ETS-H: Magnum 10ETS Terminal Server, front-mount, with integral 90-250V
AC/DC Power Supply. May be factory-configured with a variety of Ethernet fiber and
copper port modules and Serial port modules designed specifically for the
10ETS/XTS. Configure up to 36 ports in a mix of Ethernet and Serial port
combinations.
10ETSR-H: Same as Model 10ETS-H except chassis is a Reverse Mount unit.
(All signal and power cables are in the rear).
10ETS-HH: Same as Model 10ETS-H except the chassis contains two integral 90-250V
AC/DC Power supplies.
10ETSR-HH: Same as Model 10ETS-HH except chassis is a Reverse Mount unit.
(All signal and power cables are in the rear).
10ETS-L: Same as Model 10ETS-H except the integral power supply is
(L) 24/48VDC.
10ETSR-L: Same as Model 10ETS-L except chassis is a Reverse Mount unit.
(All signal and power cables are in the rear).
10ETS-LL: Same as Model 10ETS-L except the chassis contains two integral
(L) 24/48VDC Power supplies.
10ETSR-LL: Same as Model 10ETS-LL except chassis is a Reverse Mount unit.
(All signal and power cables are in the rear).
10ETS-HL: Same as Model 10ETS-HH except the integral power supplies are
one H 90-250V AC/DC and one L 24/48VDC.
10ETSR-HL: Same as Model 10ETS-HL except chassis is a Reverse Mount unit.
(All signal and power cables are in the rear).
10ETS-AC: Same as Model 10ETS-H except the power supply is an auto-sensing
worldwide AC power type (100-240V AC) using a UL-registered recessed-male
IEC 320 plug.
10ETSR-AC: Same as Model 10ETS-AC except chassis is a Reverse Mount unit.
(All signal and power cables are in the rear).
10ETSP-L: Magnum 10ETS Terminal Server, front-mount, with integral (L) 24/48V
DC Power Supply. May be factory-configured with a variety of Ethernet fiber and
copper port modules and Serial port modules designed specifically for the
10ETS/XTS. Configure up to 36 ports in a mix of Ethernet and Serial port
combinations. Supports PoE
10ETSPR-L: Same as Model 10ETSP-L except chassis is a Reverse Mount unit.
(All signal and power cables are in the rear). Supports PoE
10ETSP-LL: Same as Model 10ETSP-L except the chassis contains two integral
(L) 24/48VDC Power supplies.
10ETSPR-LL: Same as Model 10ETSP-LL except chassis is a Reverse Mount unit.
(All signal and power cables are in the rear).
Please use this URL for the complete Configuration Guide for the Magnum 10ETS.
http://www.garrettcom.com/techsupport/hardware/datasheets/10ets_dscs.pdf
Magnum 10ETS / 10XTS Installation and User Guide 06/12
6
www GarrettCom com
..
10XTS Router Terminal Server - w/Hot Swap power supplies
MODEL DESCRIPTION
10XTS-HSPHH: Magnum 10XTS Terminal Server, front-mount, with two PS
slots for two (H) Hot-Swap Power Supplies. May be factory-configured with a variety
of Ethernet fiber and copper port modules and Serial port modules designed
specifically for the 10ETS/XTS. Configure up to 36 ports in a mix of Ethernet and
Serial port combinations.
10XTSR-HSPHH: Same as Model 10XTS-HSPHH except chassis is a Reverse
Mount unit. (All signal and power cables are in the rear).
10XTS-HSPHL: Magnum 10XTS Terminal Server, front-mount, with two PS
slots for one (H) and one (L) Hot-Swap Power Supply. May be factory-configured
with a variety of Ethernet fiber and copper port modules and Serial port modules
designed specifically for the 10ETS/XTS. Configure up to 36 ports in a mix of
Ethernet and Serial port combinations.
10XTSR-HSPHL: Same as Model 10XTS-HSPHL except chassis is a Reverse
Mount unit. (All signal and power cables are in the rear).
10XTS-HSPLL: Magnum 10XTS Terminal Server, front-mount, with two PS
slots for two (L) Hot-Swap Power Supplies. May be factory-configured with a variety
of Ethernet fiber and copper port modules and Serial port modules designed
specifically for the 10ETS/XTS. Configure up to 36 ports in a mix of Ethernet and
Serial port combinations.
10XTSR-HSPLL: Same as Model 10XTS-HSPLL except chassis is a Reverse
Mount unit. (All signal and power cables are in the rear).
10XTSP-HSPLL: Magnum 10XTS Terminal Server, front-mount, with two PS
slots for two (L) Hot-Swap Power Supplies. May be factory-configured with a variety
of Ethernet fiber and copper port modules and Serial port modules designed
specifically for the 10ETS/XTS. Configure up to 36 ports in a mix of Ethernet and
Serial port combinations. Supports PoE
10XTSPR-HSPLL: Same as Model 10XTSP-HSPLL except chassis is a Reverse
Mount unit. (All signal and power cables are in the rear). Supports PoE
Magnum 10ETS / 10XTS Installation and User Guide 06/12
7
www GarrettCom com
..
10XTS Router Terminal Server - w/Fixed power supplies
MODEL DESCRIPTION
10XTS-H: Magnum 10XTS Terminal Server, front-mount, with integral 90-250V
AC/DC Power Supply. May be factory-configured with a variety of Ethernet fiber and
copper port modules and Serial port modules designed specifically for the
10ETS/XTS. Configure up to 36 ports in a mix of Ethernet and Serial port
combinations.
10XTSR-H: Same as Model 10XTS-H except chassis is a Reverse Mount unit.
(All signal and power cables are in the rear).
10XTS-HH: Same as Model 10XTS-H except the chassis contains two integral 90-250V
AC/DC Power supplies.
10XTSR-HH:Same as Model 10XTS-HH except chassis is a Reverse Mount unit.
(All signal and power cables are in the rear).
10XTS-L: Same as Model 10XTS-H except the integral power supply is
(L) 24/48VDC.
10XTSR-L: Same as Model 10XTS-L except chassis is a Reverse Mount unit.
(All signal and power cables are in the rear).
10XTS-LL: Same as Model 10XTS-L except the chassis contains two integral
(L) 24/48VDC Power supplies.
10XTSR-LL: Same as Model 10XTS-LL except chassis is a Reverse Mount unit.
(All signal and power cables are in the rear).
10XTS-HL: Same as Model 10XTS-HH except the integral power supplies are
one H 90-250V AC/DC and one L 24/48VDC.
10XTSR-HL: Same as Model 10XTS-HL except chassis is a Reverse Mount unit.
(All signal and power cables are in the rear).
10XTS-AC: Same as Model 10XTS-H except the power supply is an auto-sensing
worldwide AC power type (100-240V AC) using a UL-registered recessed-male
IEC 320 plug.
10XTSR-AC: Same as Model 10XTS-AC except chassis is a Reverse Mount unit.
(All signal and power cables are in the rear).
10XTSP-L: Magnum 10XTS Terminal Server, front-mount, with integral (L) 24/48V
DC Power Supply. May be factory-configured with a variety of Ethernet fiber and
copper port modules and Serial port modules designed specifically for the
10ETS/XTS. Configure up to 36 ports in a mix of Ethernet and Serial port
combinations. Supports PoE
10XTSPR-L: Same as Model 10XTSP-L except chassis is a Reverse Mount unit.
(All signal and power cables are in the rear). Supports PoE
10XTSP-LL: Same as Model 10XTSP-L except the chassis contains two integral
(L) 24/48VDC Power supplies.
10XTSPR-LL: Same as Model 10XTSP-LL except chassis is a Reverse Mount unit.
(All signal and power cables are in the rear).
Please use this URL for the complete Configuration Guide for the Magnum 10XTS.
http://www.garrettcom.com/techsupport/hardware/datasheets/10xts_dscs.pdf
Magnum 10ETS / 10XTS Installation and User Guide 06/12
8
www GarrettCom com
..
“HSP” Hot-Swap power supply options:
HSPM-H: AC or DC power (90-250V)
HSPM-L: 24/48V DC power (22-60V)
HSPM-BLNK: Blank cover for one hot-swap power supply slot
Following Ethernet 10/100Mb modules can be configured in Slots A and/or B only
Magnum 10ETS/XTS (Slots A, B) Port Modules:
10TS2-RJ45 Module with two 10/100Mb RJ45 ports
10TS2-HSFP Module with two 100Mb SFP open ports
100Mb SFP transceiver options for Slots A & B (Slot C w/10K4-FXSFP module):
SFP100P-FXMM2 100Mb SFP transceiver, Multimode, 2km
SFP100P-FXSM20 100Mb SFP transceiver, Singlemode, 20km
SFP100P-FXSM40 100Mb SFP transceiver, Singlemode, 40km
SFP100P-RJ45 100Mb SFP transceiver, RJ45 (auto-negotiating)
Following IRIG-B module can be configured in Slot B only
IRIGB-TMODULE Timing module for IRIG-B w/two BNC connectors
Following modules can be configured in Slot C only
Magnum 10ETS/XTS (Slots C) Port Modules:
10K4-RJ45 Module w/four 10/100 RJ45 ports
10K4PX-RJ45 Module w/four 10/100 RJ45 ports with PoE+ (802.3at) support
10K4-MLC Module w/four 100Mb multimode fiber LC ports
10K4-SLC Module w/four 100Mb singlemode fiber LC ports (20km)
10K4-SLCL Module w/four 100Mb “long-haul” singlemode fiber LC ports (40km)
10K4-MTRJ Module w/four 100Mb multimode fiber MTRJ ports
10K2-MST Module w/two multimode ST fiber ports
10K2-F10ST Module w/two multimode 10Mb ST fiber ports
10K2-MSC Module w/two multimode SC fiber ports
10K2-SSC Module w/two singlemode SC fiber ports
10K2-SSCL Module w/two “long-haul” singlemode SC fiber ports
10K4-FXSFP Module w/four 100Mb open SFP transceiver ports
Magnum 10ETS / 10XTS Installation and User Guide 06/12
9
www GarrettCom com
..
Following Serial modules can be configured in Slots C-J only
Magnum 10ETS/XTS (Slots C-J) Port Modules:
*10TS2-DB9-X-IRIGB Module w/two port DB-9 (female) with IRIG-B
10TS2-DB9-DCE Module w/two port DB-9 (female DCE)
*10TS2-DB9-DCE-IRIGB Module w/two port DB-9 (female DCE) with IRIG-B
10TS2-DB9-DTE Module w/two port DB-9 (female DTE)
*10TS2-DB9-DTE-IRIGB Module w/two port DB-9 (female DTE) with IRIG-B
10TS4-RJ45 Module w/four port RJ45
*10TS4-RJ45-IRIGB Module w/four port RJ45 with IRIG-B
* Requires IRIGB-TMODULE in Slot B
Following module can be configured in Slot I only for the 10XTS
(Not available for the 10ETS)
Magnum 10XTS (Slot I) Port Module:
10-2T1E1 Dual T1/E1 WAN adapter
Slot locations:
Options & Extras:
CONSOLE-CBLQD: Console attachment cable. Serial null modem (aka X-modem)
cable with RJ45 connector for the 10ETS/XTS on one end and a DB-9 connector on
other end.
CONSOLE-CBLQU: Same as above, but with USB connector
MNS-DX-SECURE: Optional, licensed software per 10ETS/XTS for extra security.
CONFORM05-RMOD: Conformal coating, heavy duty silicone at 5 mil thickness, for
interior PCBs, PS and modules (for moisture protection)
CONFORM08-RMOD: Conformal coating, heavy duty silicone at 8 mil thickness, for
interior PCBs, PS and modules (for corrosion in paper, mining, and oil & gas industries)
Hot-Swap power supply locations:
Magnum 10ETS / 10XTS Installation and User Guide 06/12
10
www GarrettCom com
..
2.0 INTRODUCTION
2.1 Inspecting the Package and Product
Examine the shipping container for obvious damage prior to installing this
product; notify the carrier of any damage that you believe occurred during shipment or
delivery. Inspect the contents of this package for any signs of damage and ensure that
the items listed below are included.
This package should contain:
1 Magnum 10ETS/XTS Terminal Server, base unit
(configured with user-selected port module options installed, and factory-
loaded MNS-DX or MNS-DX-SECURE software installed)
1 Set of two metal 19” rack-mounting brackets, with screws into case.
Remove the items from the shipping container. Be sure to keep the shipping
container should you need to re-ship the unit at a later date.
In the event there are items missing or damaged, contact the party from whom
you purchased the product. If the unit needs to be returned, please use the original
shipping container if possible. Refer to Section 6, Troubleshooting, for specific return
procedures.
Magnum 10ETS / 10XTS Installation and User Guide 06/12
11
www GarrettCom com
..
2.2 Product Description
Magnum 10ETS Ethernet Terminal Server
The Magnum 10ETS Terminal Server provides “Next-Generation”
configurability, reliability and functionality in a 1U hardened rack-mount package. The
10ETS offers space efficiency and advanced serial and Ethernet ports configurability for
heavy duty industrial applications where maximum port count and diversity are required.
The 10ETS also offers the flexibility of switching or routing on all of the Ethernet ports.
Each 10ETS Managed Terminal Server includes advanced thermal design techniques that
result in cooler operation of internal electronic components, leading to longer life-time
and increased reliability.
See 10ETS Product bulletin for more information.
http://www.garrettcom.com/techsupport/hardware/datasheets/10ets_dscs.pdf
Magnum 10XTS Router Terminal Server
The Magnum 10XTS Router Terminal Server offers T1/E1 routing as well as
advanced serial and Ethernet port configurability for heavy duty industrial applications
where maximum port count and diversity are required. The Magnum 10XTS is ideal for
large substation installations with large numbers of serial and Ethernet instruments and
the need for high-speed WAN access.
The Magnum 10XTS offers two WAN ports via a T1/E1 card, up to eight
Ethernet ports or 28 serial ports and IRIG-B time coding. The 10XTS provides
configurability, reliability, and functionality in a 1U hardened rack-mount package. The
10XTS also offers the flexibility of switching or routing on all of the Ethernet ports.
Each 10XTS Router Terminal Server includes advanced thermal design techniques that
result in cooler operation of internal electronic components, leading to longer life-time
and increased reliability.
See 10XTS Product bulletin for more information.
http://www.garrettcom.com/techsupport/hardware/datasheets/10xts_dscs.pdf
10ETSR (Reverse mount shown)
10XTS (Front mount shown)
Magnum 10ETS / 10XTS Installation and User Guide 06/12
12
www GarrettCom com
..
2.3 Managed Network Software for Magnum 10ETS/XTS
Magnum 10ETS/XTS comes with licensed MNS-DX software or MNS-DX-
SECURE, which allow the user to configure the Magnum 10ETS/XTS as a Managed
Switch and implements security features and other software-enabled features.
(NOTE: Magnum 10ETS/XTS will work with MNS-DX Rel v3.1.6 firmware or
higher version only. Using any earlier MNS-DX Rev-level versions will not provide
support for the Magnum 10ETS/XTS Terminal Server)
For additional information about MNS-DX, see the Magnum MNS-DX
Software User guide in pdf format, a separate document normally accessible via your
web-browser, at http://www.garrettcom.com/techsupport/index.htm#software and look
for the Magnum MNS-DX info.
Magnum 10ETS / 10XTS Installation and User Guide 06/12
13
www GarrettCom com
..
2.4 Features and Benefits
Dual Hot-swappable power supplies
The Magnum 10ETS/XTS offers configurable Dual Hot-Swappable power supplies
for redundancy and increased reliability. Available for “H” AC/DC and “L”
48/24VDC.
IRIG-B Timing modules
The Magnum 10ETS/XTS offers precision IRIG-B timing synchronization to
Protection and SCADA devices.
Managed switching for high performance Ethernet LANs
The Terminal Server provides non-blocking (all ports can run at full speed at once)
performance with standard Managed Network Software.
Switching services includes 802.1p QoS packet prioritization
The Magnum 10ETS/XTS switching hardware supports QoS, giving packet processing
priority to priority tagged packets according to the IEEE 802.1p 4-level standard. For
port- and application-specific priorities of data, including VLANs, the QoS software
may be configured by the user.
Fiber Port configurability
Magnum 10ETS/XTS Terminal Servers are designed to naturally include fiber ports,
and support mixes of multimode, singlemode, 10Mb and 100Mb speed; full-and half-
duplex; classic FX Small Form Factor (SFF) and Small Form Pluggable (SFP)
connectors for fiber cable.
Relay Contacts for monitoring internal power and user-defined software events
Two Alarm Relay contacts monitor basic operations. One is for hardware, and will
signal loss of power internally. The other is software controlled and will signal user-
defined software events such as a security violation or a redundancy fault condition.
19” Rack-mounting
The standard rack mounting provides Ethernet ports, Serial ports and status LEDs in
front, service connections (power input and management console) in the rear.
“Reverse” rack mounting provides status LEDs in front and all cabling connections in
the rear. For best reliability and cooling, 1U vertical space above and below is
recommended.
Heavy-duty design for Industrial applications and extended temperature
operation
10ETS/XTS Terminal Servers includes advanced thermal design techniques that
result in cooler operation of internal electronic components, leading to longer life-
time and increased reliability. The ambient temperature dual-rating is 60`C per UL
methods, and 85°C per IEC type test methods.
Magnum 10ETS / 10XTS Installation and User Guide 06/12
14
www GarrettCom com
..
MNS-DX licensed Management Software
Managed Networks Software (MNS) basic version, combined with a
Magnum 10ETS/XTS, provides power and efficiency in a managed Ethernet
platform. A full range of industry-standard software functions in the MNS-DX
software product enables the versatile Magnum 10ETS/XTS to perform efficiently
in a wide range of managed LAN applications, including redundant topologies.
MNS-DX-SECURE (optional, for extra security)
Magnum MNS-DX-SECURE software is designed for those customers demanding
extra security in their networks. MNS-DX-SECURE is an optional item--licensed per
10ETS/XTS. All of the features in regular MNS-DX are included, plus extra security.
RSTP-2004 for rings and meshes, fastest fault recovery, interoperability
RSTP-2004 provides reliable fast recovery from a fault in a redundant LAN, which
may include Magnum switches and routers as well as other vendors industry-standard-
RSTP products. Redundant topologies may include rings, dual-rings, and complex
meshes.
This manual suits for next models
1
Table of contents
Other GarrettCom Server manuals
