Gas Clip MGC simple User manual
Contact Information
MGC-S QSG v1.01
Portable gas detectors you can count on
Portable gas detectors you can count on
Quick-Start Guide
Multi Gas Clip
Simple
Gas Clip Technologies, Inc.
610 Uptown Blvd, Suite 4100
Cedar Hill, TX 75104 USA
Phone: +1.972.775.7577
Fax: +1.972.775.2483
Toll Free: 1.877.525.0808
E-mail: info@gascliptech.com
Website: www.gascliptech.com
Battery Information
This detector is designed so that the battery won't need charging
or replacing during the life of the detector.
Detector Life Countdown
Once activated, the detector will display 24 months of life
remaining. Detector will continue to countdown and display
months remaining until 30 days remain. Display will then show
days remaining until end of life.
Additional Questions?
For additional information on the Multi Gas Clip Simple gas
detector regarding programing, bump testing, calibrating, etc.
please refer to the Multi Gas Clip Simple User’s Manual. The
manual and other helpful videos & information are available for
viewing or download at www.gascliptech.com.
Entry Description
1 Alarm Condition
2Life Remaining
3Calibration/Test Mode
4Battery Indicator
5Gas Readings
6 Gas Identifiers
Warning: Users must familiarize themselves with the
icons in both alarm and non-alarm states.
Warning: If the display is missing icons, or cannot be
clearly read, discontinue use and contact GCT.
Warning: The IR LEL sensor will not detect hydrogen (H2) or
acetylene (C2H2) gases however, due to their cross-sensitive
nature, the CO sensor will go into alarm well below 10% LEL.
READ FIRST BEFORE OPERATION
Display Components
The Gas Identifier (6) and the associated Alarm Condition (1)
will flash when a gas reading exceeds its alarm threshold.
Factory Default Alarms
Sensor
Low
High
TWA
STEL
H2S
10
15
10
15
CO
35
200
35
50
O2
19.5
23.5
LEL
10
20
The Multi Gas Clip Simple is a personal safety device designed to
detect the presence of hydrogen sulfide (H2S), carbon monoxide (CO),
oxygen (O2) and combustible gases (LEL). Ensure that you have been
properly trained on the use of the detector and the appropriate
actions to take in the event of an alarm condition before operation.
Turning On the Detector
To activate the detector, press and briefly hold down the power/menu
button. Once activated, the detector will begin to display Gas
Readings immediately. Each Gas Identifier will show a chasing “0” for
the Gas Reading while it is stabilizing and self-testing. Once all Gas
Identifiers have completed the warm up and stabilization sequence
(<65 seconds) the detector is ready to detect all applicable gases.
Turning Off the Detector
This detector is not designed to be turned off. Once activated, it will
run continuously for 24 months.
Auto Zeroing
Continuously hold down the power/menu button to auto zero the
detector. Release button when display shows "AUTO ZERO". Wait
a few seconds then press the button briefly when display shows
"APPLY GAS". Detector has been successfully auto zeroed.
Bump Testing and Calibrating
These operations can be performed manually or automatically using
the MGC Simple Dock or MGC Simple Wall Mount Dock. Refer to the
Multi Gas Clip Simple User's Manual for instructions.
Before each use, check
that all sensor and alarm
ports are clear of any
debris or obstructions.
DO NOT auto zero the
detector in a combustible
atmosphere.
DO NOT auto zero in
temperatures above
104°F (40°C) or below
32°F (0°C).
days
months
months months
Fully Operational
months
Stabilization
months
Entry Description
1 Alarm Condition
2Life Remaining
3Calibration/Test Mode
4Battery Indicator
5Gas Readings
6 Gas Identifiers
Warning: Users must familiarize themselves with the
icons in both alarm and non-alarm states.
Warning: If the display is missing icons, or cannot be
clearly read, discontinue use and contact GCT.
Warning: The IR LEL sensor will not detect hydrogen (H2) or
acetylene (C2H2) gases however, due to their cross-sensitive
nature, the CO sensor will go into alarm well below 10% LEL.
READ FIRST BEFORE OPERATION
Display Components
The Gas Identifier (6) and the associated Alarm Condition (1)
will flash when a gas reading exceeds its alarm threshold.
Factory Default Alarms
Sensor
Low
High
TWA
STEL
H2S
10
15
10
15
CO
35
200
35
50
O2
19.5
23.5
LEL
10
20
The Multi Gas Clip Simple is a personal safety device designed to
detect the presence of hydrogen sulfide (H2S), carbon monoxide (CO),
oxygen (O2) and combustible gases (LEL). Ensure that you have been
properly trained on the use of the detector and the appropriate
actions to take in the event of an alarm condition before operation.
Turning On the Detector
To activate the detector, press and briefly hold down the power/menu
button. Once activated, the detector will begin to display Gas
Readings immediately. Each Gas Identifier will show a chasing “0” for
the Gas Reading while it is stabilizing and self-testing. Once all Gas
Identifiers have completed the warm up and stabilization sequence
(<65 seconds) the detector is ready to detect all applicable gases.
Turning Off the Detector
This detector is not designed to be turned off. Once activated, it will
run continuously for 24 months.
Auto Zeroing
Continuously hold down the power/menu button to auto zero the
detector. Release button when display shows "AUTO ZERO". Wait
a few seconds then press the button briefly when display shows
"APPLY GAS". Detector has been successfully auto zeroed.
Bump Testing and Calibrating
These operations can be performed manually or automatically using
the MGC Simple Dock or MGC Simple Wall Mount Dock. Refer to the
Multi Gas Clip Simple User's Manual for instructions.
Before each use, check
that all sensor and alarm
ports are clear of any
debris or obstructions.
DO NOT auto zero the
detector in a combustible
atmosphere.
DO NOT auto zero in
temperatures above
104°F (40°C) or below
32°F (0°C).
days
months
months months
Fully Operational
months
Stabilization
months
Contact Information
MGC-S QSG v1.01
Portable gas detectors you can count on
Portable gas detectors you can count on
Quick-Start Guide
Multi Gas Clip
Simple
Gas Clip Technologies, Inc.
610 Uptown Blvd, Suite 4100
Cedar Hill, TX 75104 USA
Phone: +1.972.775.7577
Fax: +1.972.775.2483
Toll Free: 1.877.525.0808
E-mail: [email protected]
Website: www.gascliptech.com
Battery Information
This detector is designed so that the battery won't need charging
or replacing during the life of the detector.
Detector Life Countdown
Once activated, the detector will display 24 months of life
remaining. Detector will continue to countdown and display
months remaining until 30 days remain. Display will then show
days remaining until end of life.
Additional Questions?
For additional information on the Multi Gas Clip Simple gas
detector regarding programing, bump testing, calibrating, etc.
please refer to the Multi Gas Clip Simple User’s Manual. The
manual and other helpful videos & information are available for
viewing or download at www.gascliptech.com.
Table of contents
