Gazelle G9406-Log User manual

G9406-Log
1
2
3
4
5
6
7
8
9
①
②
③
⑤
④
1 2 3 4
5
6
9
P/N:11040110****X
8
7
1.Introduction
G9406-Log with Bluetooth function is a stable, safe, reliable mini sound
meter, widely used in noise detection, quality control, health control,
environmental noise
other places.
measurement in factory, traffic, home audio and
This operating manual includes relevant safety information and warnings.
Please read this manual carefully and observe all cautions.
Warning:
Before using the product, please read the operation rules carefully.
2.Out of the Box
Open the packing box and take out the meter. Please check carefully
if any items are missing or damaged.
1.Blister---------------------------------------- 1
2.Wind-proof ball 1----------------------------
3.Operating manual 1------------------------
3.Operation Safety Rules
This product strictly follows the requirements of SJ/T 10423“General
specification for sound level meters” in design and production.
1.Please check the meter and the accessories before using and beware
of any damage or abnormal phenomenon. If you find the case is
damaged or the LCD shows nothing, or you consider that the meter
could not work properly anymore, please stop using it.
2.Observe the operating instructions while measuring.
3.Do not open the meter at will or change internal wiring to avoid
damages to the mater.
4.When the LCD displays “ ”, replace the battery timely. Remove
battery if the meter is not used for a long time.the
5.Do not store or use the meter in high temperature, high humidity,
flammable, combustible or strong electromagnetic environment.
6.Please use soft cloth and neutral detergent to clean the case for
maintenance. Do not use grinding agent and solvent to avoid case
corrosion and damage to the meter.
7.This product has passed CE certification.
4.Product Exterior
1.Wind-proof ball
2.Microphone
3.Meter case
4.LCD display
5.Function keys
Wind
screen
Foam
5. Display Interface
Maximum measurement
Minimum measurement
Data hold
Low battery
A weighted and noise unit
Slow response rate
Fast response rate
Measurement value
6. Key Function and Setup
(remark : “short press”means : about 1second continuous press ;“long
press” means : about 2 second continuous press）
1. ON/OFF/ Bluetooth communication
Short press once to start up; short press again to power off.
Bluetooth communication : Under the state of boosting unit , long press
to enter Bluetooth communication mode, and then long press again to
quit Bluetooth communication mode
2. FAST/SLOW
Sampling time: When measuring, pressing this key to select between
fast time of 125ms and slow time of 1s.
3. MAX/MIN
Pressing this key to select maximum, minimum and normal value
measurement; when maximum or minimum measurement is selected,
the meter always shows the maximum reading or the minimum reading.
4. HOLD/BL
HOLD: Short press this key once to hold the measurement; short press
the key once again to exit data hold and continue normal measurement.
BL: long press this key to turn on backlight, and long press it again to
turn off backlight.
5.Automatic shutdown
No operation 5 minutes after , then shut down the unit automatically
(the default mode is of automatic shutdown mode)
When you want to remove the automatic shutdown function, hold down
the "hold" + " " key to boot. LCD has a "APO OFF" character prompt,
the automatic shutdown function will be removed .
Bluetooth communication symbol indication
Mini Sound Meter (Buletooth
Version) Operating Manual
G9406-Log

iENV
G9406-Log
20:91:48:6C:83:2D 66.4dBA
iENV
G9406-Log
20:91:48:6C:83:2D
Bluetooth working APP Bluetooth searching APP connected
connected
Broadcasting
connected
Broadcasting
connected
8.Performance Testing
1.Technical Parameter
Range :30～130dB
Resolution: 0.1dB
Accuracy:±1.5dB
Frequency Response: 31.5Hz～8KHz
Ambient Temperature：23℃ ±5℃
Ambient Humidity：≤80%RH
Temperature Coefficient 0.1 X Accuracy /℃:
2. General Type
a. LCD display: 4-bit LCD display. The maximum display is 9999.
b. Overload indication: The meter shows “UN” when under range, and
shows “OL” when over range.
c. Low battery indication: prompt “ ”.
d. Sampling rate: fast rate 125ms, slow rate 1s
e. Sensor type: 1/2 inch condenser microphone
f. Impact strength: Can withstand the impact of landing from 1 meter height
g. Power requirement: 1.5V batteries (AAA) ×3
h. Product size: 154mm×55mm×28mm
I. Spec of thread to connect the product with three tripod
j. Weight: 116g
: m¼”
3. Environment Limitation
a. Indoor use
b. Maximum operating height: 2000m
c. Pollution level: 2
d. Working temperature and humidity:
0℃~30℃ (not greater than 80%RH)
30℃~40℃ (not greater than 80%RH)
40℃~50℃ (not greater than 45%RH)
e. Storage temperature and humidity:
-20℃~60℃ (not greater than 80%RH)
4. General Maintenance
Warning: please do not open the meter case to avoid affecting device
accuracy or damage to the meter.
a. Maintenance and service of the meter should be accomplished by
professional personnel or designated maintenance department.
b. Clean the case by dry cloth periodically. Detergent with abrasive or
solvent composition shall not be used.
5. Battery Installation and Replacement
a. This device uses 3 pieces of AAA 1.5V batteries. Please see figure
below for steps of battery installation and replacement.
b. Turn the panel down, push the battery cover open in the direction of
the arrow, lift the cover and remove the batteries; install new batteries
in accordance of polarity indications.
c. Please use batteries of same type instead of improper ones.
d. Close the cover tightly after installing new batteries.
7.Bluetooth APP specification
1. To connect Bluetooth , you need to install the application (iENV APP)
on the smartphone
2. iOS device access it in App Store , Android device access it in
Play Store Please login to download.or www.gazelleindustrial.com
Compatibility:
ios 8.4 or higher version
Android 4.3 or higher version
Bluetooth 4.0 or higher version
Memory 1G or more
3. Before Bluetooth APP and product are connected , you need to open
the Bluetooth at the same time, and through the APP search the
Bluetooth, and select the corresponding products to be connected in
iENV APP
when in the working state, long press the power button to turn on or
off the Bluetooth
a. Bluetooth icon is flashing, indicating that the product is not connected
with APP
b. Bluetooth icon isn’t flashing, indicating that the product is connected
with APP