GE APEL50 User manual

Write the model and serial
numbers here:
Model #_________________
Serial # _________________
You can find them on a label on
the back of the dehumidifier.
GE is a trademark of the General Electric Company. Manufactured under trademark license.
OWNER’S MANUAL
DEHUMIDIFIER
49-5000427 Rev. 0 10-19 GEA
APEL50
APEW50
APER50
ENGLISH/ESPAÑOL
SAFETY INFORMATION .........3
OPERATING INSTRUCTIONS
Controls ..............................4
How the Dehumidifier Operates .........5
Automatic Defrost .....................5
Choosing a Location ...................5
Removing Collected Water .............6
Water Level...........................7
Bucket Operation ......................7
CARE AND CLEANING
Grille and Case ........................8
Water Bucket .........................8
Air Filter..............................8
Bucket Filter ..........................9
Storage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
TROUBLESHOOTING TIPS......10
ELECTRIC SCHEMATIC
DIAGRAM.........................12
LIMITED WARRANTY ...........13
CONSUMER SUPPORT ..........14

249-5000427 Rev. 0
THANK YOU FOR MAKING GE APPLIANCES A PART OF YOUR HOME.
Whether you grew up with GE Appliances, or this is your first, we’re happy to have you in the family.
We take pride in the craftsmanship, innovation and design that goes into every GE Appliances
product, and we think you will too. Among other things, registration of your appliance ensures that we
can deliver important product information and warranty details when you need them.
Register your GE appliance now online. Helpful websites and phone numbers are available in the
Consumer Support section of this Owner’s Manual. You may also mail in the pre-printed registration
card included in the packing material.

49-5000427 Rev. 0 3READ AND SAVE THESE INSTRUCTIONS
IMPORTANT SAFETY INFORMATION
READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE
SAFETY INFORMATION
WARNING For your safety, the information in this manual must be followed to minimize the risk of
fire, electric shock or personal injury.
■ Use this appliance only for its intended purpose as
described in this Owner’s Manual.
■ This dehumidifier must be properly installed and
grounded as described in this manual before it is
used.
■ Never operate this dehumidifier in an area that is
likely to accumulate standing water. If this condition
develops, for your safety disconnect the power supply
before stepping into the water.
■ Never unplug your dehumidifier by pulling on the
power cord. Always grip plug firmly and pull straight
out from the receptacle.
■ Replace immediately all electric service cords
that have become frayed or otherwise damaged.
A damaged power supply cord must be replaced
with a new power supply cord obtained from the
manufacturer and not repaired. Do not use a cord that
shows cracks or abrasion damage along its length or
at either the plug or connector end.
■ If the receptacle does not match the plug, the
receptacle must be changed out by a qualified
electrician
■ If the SUPPLY CORD is damaged, it must be replaced
by the manufacturer, its service agent or similary
qualified person in order to avoid a hazard.
■ The appliance shall be installed in accordance with
national wiring regulations.
■ Turn the dehumidifier OFF and unplug it before
cleaning.
■ GE Appliances does not support any servicing of the
dehumidifier. We strongly recommend that you do not
attempt to service the dehumidifier yourself.
■ For your safety, do not store or use combustible
materials, gasoline or other flammable vapors or
liquids in the vicinity of this or any other appliance.
■ All dehumidifiers contain refrigerants, which under
federal law must be removed prior to product
disposal. If you are getting rid of an old product
with refrigerants, check with the company handling
disposal about what to do.
■ Do not use outdoors.
■ This dehumidifier is intended for indoor residential
applications only. This dehumidifier should not be
used for commercial or industrial applications.
■ These R410A Dehumidifier Systems require
contractors and technicians to use tools, equipment
and safety standards approved for use with this
refrigerant. DO NOT use equipment certified for R22
refrigerant only.
■ This appliance can be used by persons with reduced
physical, sensory or mental capabilities or lack of
experience and knowledge if they have been given
supervision or instruction concerning use of the appliance
in a safe way and understand the hazards involved.
WARNING USE OF EXTENSION CORDS
RISK OF FIRE. Could cause serious injury or death.
■ DO NOT use an extension cord with this Dehumidifier.
■ DO NOT use surge protectors or multi-outlet adaptors
with this Dehumidifier.
HOW TO CONNECT ELECTRICITY
Do not, under any circumstances, cut or remove the third
(ground) prong from the power cord. For personal safety,
this appliance must be properly grounded.
DO NOT use an adapter plug with this appliance.
The power cord of this appliance is equipped with a
3-prong (grounding) plug which mates with a standard
3-prong (grounding) wall outlet to minimize the possibility
of electric shock hazard from this appliance.
Have the wall outlet and circuit checked by a qualified
electrician to make sure the outlet is properly grounded.
Where a 2-prong wall outlet is encountered, it is your
personal responsibility and obligation to have it replaced
with a properly grounded 3-prong wall outlet.
The dehumidifier should always be plugged into its own
individual electrical outlet, which has a voltage rating
matching the rating plate.
This provides the best performance and also prevents
overloading house wiring circuits, which could cause a
fire hazard from overheated wires.
RECYCLING INFORMATION
For appliance recycling information please visit www.geappliances.com/recycling.

449-5000427 Rev. 0
OPERATING INSTRUCTIONS
Controls
Controls
NOTE: When the bucket is full or removed, the controls
cannot be set.
1. Power Pad
Press to turn the dehumidifier on and off.
2. Filter Timer
After 250 hours of operation, the Clean the Filter
indicator light will glow to remind you to clean the filter.
Remove the filter and clean it.
Press to turn off the Clean the Filter light. See the Care
and Cleaning section.
3. Humidity Set Control Pads
The humidity level can be set within a range of 35%
RH (Relative Humidity) to 80% RH (Relative Humidity)
in 5% increments or at NS for continuous operation. To
set the unit for continuous operation, press the – pad
until the screen reads NS.
NOTE: If NS (Nonstop) is selected, the dehumidifier will
operate continuously at its maximum dehumidification
settings if attached to a hose to drain or until the bucket
is full.
For drier air, press the – pad and set to a lower
percent value (%).
For damper air, press the +pad and set to a higher
percent value (%).
When you first use the dehumidifier, set the humidity
control to 45% or 50%. Allow at least 24 hours for the
dehumidifier to achieve the humidity level. If you still
have damper air than desired, set the humidity level
to a lower setting or select Nonstop for maximum
dehumidification.
4. Display
Shows the set % humidity level while setting, then shows
the actual (+/– 5% accuracy) room % humidity level.
5. Fan Speed Pad
Controls the fan speed.
Press to select either High, Medium or Low fan
speed.
Set the fan control to High for maximum moisture
removal. When the humidity has been reduced and
quiet operation is preferred, set the fan control to
Medium or Low.
6. Delay Off
While the dehumidifier is in operation, press this pad to
set it to automatically turn off in 2 hours or 4 hours.
7. Pump
Activates the internal pump function. Press for 3 seconds
to activate the internal pump for automatic removal of
condensate. The internal pump indicator light will remain
illuminated after 3 seconds. Press to deactivate the
pump.
Other Features
Empty Light
Glows when the bucket is ready to be emptied, or when the
bucket is removed or not replaced in the proper position.
Alarm
If the bucket is full or missing for more than 3 minutes, an
alarm will sound for about 10 seconds to remind you to
empty and replace the bucket.
Auto Shut Off
The Water Level Control Switch shuts off the dehumidifier
when the bucket is full, or when the bucket is removed
or not replaced in the proper position. NOTE: Fan will
continue to run approximately 3 minutes after bucket is
removed.
Auto Defrost
When frost builds up on the evaporator coils, the
compressor will cycle off and the fan will continue to run
until the frost disappears.
Power Outage
In the case of a power outage or interruption, the unit will
automatically restart, in the settings last used, after the
power is restored.
5
Nonstop
Humidity %
On
Filter
Power -+FanPump
Hold 3 Sec To Rest Hold 3 Sec
Requires Hose
Filter
Timer
Delay
Off
Empty
Pump
4 hour
2 hour
Medium
Low
High
Bucket Full light indicates
bucket needs to be
emptied or is not in place
in the unit
Pump light
indicates
the pump is
activated
4 hour or 2 hour
delay off
indicator lights
Continuous
Operation on
indicator light
Power On
indicator light
Clean the Filter
indicator light
High, Medium
and Low fan
indicator light

49-5000427 Rev. 0 5
Using the Dehumidifier
Choosing a Location
How the Dehumidifier Operates
Moist, humid air is drawn over a cold refrigerated
dehumidifying coil. Moisture in the air condenses on this coil
and drains into a bucket (or through a hose and drain).
Dry, clean air is drawn through the condenser where it is
heated and discharged out the top grille into the room.
It is normal for the surrounding air to become slightly
warmer as the dehumidifier operates.
Automatic Defrost
When frost builds up on the evaporator coils, the
compressor will cycle off and the fan will continue to run
until the frost disappears.
When the coil is defrosted, the compressor or fan will
automatically restart and dehumidifying will resume.
OPERATING INSTRUCTIONS
When first using the dehumidifier, operate the unit continuously for 24 hours.
A dehumidifier operating in a basement will have little or no
effect in drying an adjacent enclosed storage area, such as
a closet, unless there is adequate circulation of air in and
out of the area.
■ Do not use outdoors.
■ This dehumidifier is intended for indoor residential
applications only. This dehumidifier should not be used
for commercial or industrial applications.
■ Place the dehumidifier on a smooth, level floor strong
enough to support the unit with a full bucket of water.
■ Allow at least 18 inches of air space on all sides of the
unit for good air circulation.
■ Place the dehumidifier in an area where the temperature
will not fall below 41°F (5°C) or above 90°F (32°C). The
coils can become covered with frost at temperatures
below 41°F, which may reduce performance.
■ The suggested range of relative humidity is between
30% and 90%
■ Use the dehumidifier in cooking, laundry, bathing and
dishwashing areas that have excessive moisture.
NOTE: Place the dehumidifier away from the clothes
dryer.
■ Use the dehumidifier to prevent moisture damage
anywhere books or valuables are stored.
■ Use the dehumidifier in a basement to help prevent
moisture damage.
■ The dehumidifier must be operated in an enclosed area
to be most effective.
■ Close all doors, windows and other outside openings to
the room.
NOTE: The dehumidifier has rollers to aid placement,
but it should only be rolled on smooth, flat surfaces.
Do not attempt to roll the dehumidifier on carpet or
over objects.
41 °F
(5 °C)
41 °F
(5 °C)
Above Below
Correct Wrong
at least 18 inches
at least 18 inches

649-5000427 Rev. 0
Using the Dehumidifier
Removing Collected Water
There are 3 ways to remove collected water:
Use the bucket. When the bucket is removed, the unit will
shut off. Empty and replace the bucket.
IMPORTANT: Do not use the hose if using the bucket to
collect water. When the hose is connected, water will flow
through it onto the floor instead of into the bucket.
NOTES:
■ Do not remove the bucket while the dehumidifier is
operating or if it has just stopped operating. This might
cause some water to drip from the drain pan.
■ The bucket must be in place and securely seated for the
dehumidifier to operate.
Use a hose. Water can be automatically emptied into a
floor drain by attaching a garden water hose (not included).
1. Remove the bucket from the front of the unit.
2. Open the drain cover on the side of the unit.
3. Thread a garden hose (not supplied) onto the nozzle, cut
to length, and lead it to the floor drain.
4. Replace the bucket in the unit.
NOTE: The bucket must be in place and securely seated
for the dehumidifier to operate.
Use the internal pump. Water can be automatically
emptied into a remote location by attaching the included
pump hose.
1. Attach the pump hose to the hose connector by pushing
the tube fitting into the connector until it fits into place
(should not be able to remove the hose when pulled).
2. Position the hose discharge to the desired location.
3. Make sure the pump is activated. To activate the pump,
press and hold the Pump button for 3 seconds. The
Pump indicator light will flash then remain illuminated
once the 3 seconds are complete.
IMPORTANT: Pump will not begin removing water until
the bucket is full. After pump button has been activated by
holding for 3 seconds, the pump will remain on stand-by.
When bucket is full, pump will automatically begin removing
water and stop when bucket is emptied. This cycle will
continue until pump button is deactivated.
IMPORTANT: Make sure the condensate hose is properly
connected and is not kinked, bent or cracked as this may
cause water to flow onto the floor. The bucket must also be
fully seated for the pump to work properly. Do not operate
the machine if the room temperature is 32°F or below.
NOTES:
■ Maximum lift height is 16ft.
■ The bucket must be in place and securely seated for the
dehumidifier and pump to operate.
Make sure to install hose (included) before activating the
pump.
OPERATING INSTRUCTIONS
Always make sure the water bucket is locked into place on the dehumidifier.
drain hose
nozzle

49-5000427 Rev. 0 7
Using the Dehumidifier
Removing Collected Water (Continued)
Water Level
The dehumidifier will turn off automatically when the bucket
is full, or when the bucket is removed or not replaced in the
proper position.
The bucket must be replaced in the proper position for the
dehumidifier to work. The bucket full light will be on and the
dehumidifier will not run if the bucket is not in the proper
position.
Bucket Operation
DO NOT remove the foam piece in the bucket assembly.
If removed the Dehumidifier will not work properly.
When the coil is defrosted, the compressor or fan will
automatically restart and dehumidifying will resume.
OPERATING INSTRUCTIONS
To Install Hose: Push in hose and gently pull to make
sure it is secure. Should not be able to be removed.
To Release Hose: Hold the grey ring while pulling to
remove.
NOTE: DO NOT kink or crimp hose, as it can block water
flow.
Push hose in
1. Hold grey ring in
2. Pull hose out

849-5000427 Rev. 0
Care and Cleaning
CARE AND CLEANING
Air Filter
The air filter behind the front grille should be checked and
cleaned at least every 250 hours of operation or more often
if necessary.
After 250 hours of operation, the Clean the Filter indicator
light will glow to remind you to clean the filter. Remove the
filter and clean it. Replace the filter and press the Filter
Timer pad to turn off the Clean the Filter light.
To remove:
Remove the bucket. Grasp the filter edge, and pull it
straight down and out.
To clean:
Clean the filter with warm, soapy water. Rinse and let the
filter dry before replacing it.
NOTE: DO NOT put the filter in an automatic dishwasher.
CAUTION DO NOT operate the dehumidifier
without a filter because dirt and lint will clog it and reduce
performance.
Grille and Case
To clean the case:
Use water and a mild detergent. Do not use
bleach or abrasives.
To clean the front grille:
Use a vacuum attachment or brush.
Water Bucket
To clean:
Every few weeks, clean the bucket to prevent growth of
mold, mildew and bacteria. Partially fill the bucket with clean
water and add a little mild detergent. Swish it around in the
bucket, empty and rinse.
NOTE: Do not use a dishwasher to clean the water bucket.
To remove:
Remove the bucket and pour out any water.
To replace:
Slide the bucket into the dehumidifier.
NOTE: The bucket must be in place and securely seated
for the dehumidifier to operate.
Turn off the dehumidifier and remove the plug from the wall outlet before cleaning.
Air Filter

49-5000427 Rev. 0 9
Care and Cleaning
Storage
If the unit is to be stored for an extended period of time,
take the following actions before putting away the machine.
1. Empty the bucket of all water.
2. Clean the water bucket and bucket filter per instructions.
3. Allow water bucket to dry and reinstall.
4. Remove pump hose and store with unit.
To Release Hose: Hold the grey ring while pulling the
hose to remove.
Bucket Filter
The bucket filter is located inside the bucket near the
bottom. The filter should be checked when cleaning the
bucket. If the filter has any debris on it, gently remove
the filter as described below and rinse with warm water.
Replace the filter in the bucket once it is clean.
IMPORTANT: Be careful not to tear or damage filter
during removal, cleaning or replacement. Do not use the
dishwasher to clean the filter.
TO REMOVE THE FILTER:
1. Squeeze both clasp inward to disengage clasp clips from
water tank cover. Lift the cover upwards to remove.
2. Lift the end of the filter upwards to remove the filter.
Rotate and lift filter up
TO REPLACE THE FILTER:
3. Place large end of filter above tabs, press filter down
firmly to spread tabs. Once filter is between tabs press
filter inward to engage tabs into filter.
4. Replace water tank cover and handle.
Cover
CARE AND CLEANING
1. Hold grey ring in
2. Pull hose out

10 49-5000427 Rev. 0
Troubleshooting Tips... Before you call for service
TROUBLESHOOTING TIPS
Save time and money! Review the charts on the following pages first and you may not need to call for service.
Problem Possible Cause What To Do
Dehumidifier does not
start
The dehumidifier is unplugged. Makes sure the dehumidifier’s plug is pushed
completely into the outlet.
The fuse is blown/circuit breaker
is tripped.
Check the house fuse/circuit breaker box and replace
the fuse or reset the breaker.
Dehumidifier has reached its
preset level or bucket is full.
The dehumidifier automatically turns off when either
condition occurs. Change to a lower setting or empty
the bucket and replace properly.
Bucket is not in the proper
position.
The bucket must be in place and securely seated for
the dehumidifier to operate.
Power Failure. There is a protective time delay (up to 3 minutes) to
prevent tripping of the compressor overload. For this
reason, the unit may not start normal dehumidification
for 3 minutes after turning back on.
Dehumidifier does not dry
the air as it should
Did not allow enough time to
remove the moisture.
When first installed, allow at least 24 hours to maintain
the desired dryness.
Airflow is restricted. Make sure there are no curtains, blinds or furniture
blocking the front of back of the dehumidifier. See the
Choosing a Location section.
Dirty Filter See the Care and Cleaning section.
The Humidity Control may not be
set low enough.
For drier air, press the – pad and set to a lower
percent value (%) or at NS (Nonstop) for maximum
dehumidification.
Doors and windows may not be
closed tightly.
Check that all doors, windows and other openings are
securely closed.
Clothes dryer may be blowing
moisure-laden air into the room.
Install the dehumidifier away from the dyer. The dryer
should be vented to the outside.
Room temperature is too low. Moisture removal is best at higher room temperatures.
Lower room temperatures will reduce the moisture
removal rate. Models are designed to be operated at
temperatures above 41°F (5°C).
Dehumidifier runs too
much
Area to be dehumidified is too
large.
The capacity of your dehumidifier may not be adequate.
Doors and windows are open. Close all doors and windows to the outside.
Frost appears on the coils Dehumidifier has been turned on
recently, or room temperature is
below 41°F (5°C)
This is normal. Frost will usually disappear within 60
minutes. See the Automatic Defrost section
Control cannot be set The compressor will turn off and
the fan will automatically continue
to run for approximately 3 minutes
at a fixed setting.
This is normal. Wait approximately 3 minutes and set
the fan as desired.
Fan noise Air is moving through the
dehumidifier.
This is normal.
Water on floor Hose connection may be loose. Check the hose connection. See the Removing
Collected Water section.
Intended to use the bucket to
collect water, but a hose was
attached.
Disconnect the hose if using a bucket to collect water.
See the Removing Collected Water section.
Bucket Full LED light
flashing and alarm sounds
while drain hose is
connected.
Drain hose not tight on fitting. Check drain hose connection.
Drain hose is kinked. Ensure the drain hose is pointed straight down to the
floor and is not kinked in anyway.

49-5000427 Rev. 0 11
NOTES
Notes

12 49-5000427 Rev. 0
Electric Schematic Diagram
ELECTRIC SCHEMATIC DIAGRAM
The electric schematic diagram is subject to change without notice.
Please refer to the correct one on the unit.
TRANSFORMER
COM NO COM
WH
BU BN
CN5 CN7
AP2 BU
PUMP
LBK(BN)
WH(BU)
COMP
FAN N1
BU YE BK WH YE
RD
CBU
M1 R
60000700064503
G
FAN MOTOR COMP.
BUCKET-SWITCH
SA2
LIQUID LEVEL SWITCH
SA1
HUMIDITY
SENSOR NO
BK
CN4
DISPLAY
BOARD
TUBE
TR-OUT TR-IN
CN6
PUMP
M2
TEMP.LIMITER
RD
CN2
T-PIPE AP1
MAIN BOARD L
N
RT1
θ
TUBE
TEMP.SENSOR
RT2
θ
DISCHARGE
TEMP.SENSOR
GN(YEGN)
BU POWER
G
CAP.
C1
BN
CAP.
C2
RD
YEGN
S
COMP.
YEGN
G

49-5000427 Rev. 0 13
LIMITED WARRANTY
GE Appliances Dehumidifier Limited Warranty
■ Customer instruction. This owner’s manual provides
information regarding operating instructions and
user controls.
■ Improper installation. If you have an installation
problem, or if the product is of improper capacity,
contact your dealer or installer. You are responsible
for providing adequate electrical connecting facilities.
■ Failure of the product resulting from modifications
to the product or due to unreasonable use including
failure to provide reasonable and necessary
maintenance.
■ Replacement of house fuses or resetting of circuit
breakers.
■ Failure due to corrosion.
■ Damage to the product caused by improper power
supply voltage, accident, fire, floods or acts of God.
■ Incidental or consequential damage caused by
possible defects with this product.
■ Damage caused after delivery.
What GE Appliances Will Not Cover:
This limited warranty is extended to the original purchaser and any succeeding owner for products purchased for
home use within the USA.
Some states do not allow the exclusion or limitation of incidental or consequential damages. This limited warranty
gives you specific legal rights, and you may also have other rights which vary from state to state. To know what your
legal rights are, consult your local or state consumer affairs office or your state’s Attorney General.
Exclusion of implied warranties: Except where prohibited or restricted by law, there are no warranties, whether
express, oral or statutory which extend beyond the description on the face hereof, including specifically the implied
warranties of merchantability or fitness for a particular purpose.
Warrantor: GE Appliances, aHaier company
Louisville, KY 40225
EXCLUSION OF IMPLIED WARRANTIES—Your sole and exclusive remedy is product repair as provided in this
Limited Warranty. Any implied warranties, including the implied warranties of merchantability or fitness for a
particular purpose, are limited to one year or the shortest period allowed by law.
For The Period Of: GE Appliances Will Replace:
One Year
From the date of the original
purchase
Replacement unit for any product which fails due to a defect in materials or
workmanship. The replacement unit is warranted for the remainder of your product’s
original one-year warranty period. The replacement unit may either be a new unit
or a refurbished unit.
■Properly pack your unit. We recommend using
the original carton and packing materials.
■ Return the product to the retail location where
it was purchased.
■Include in the package a copy of the sales receipt
or other evidence of date of original purchase. Also
print your name and address and a description of the
defect.
In Order to Make a Warranty Claim During the First 90 Days from the Date of Original Purchase:
■ Locate your original sales receipt and make a note
of your model and serial number.
■ Call GE Appliances at 800.432.2737 to initiate the
product replacement process.
■ You will be asked to provide your name, address,
date of purchase, model and serial number.
■ GE Appliances will arrange for a carton to be sent to
your home to recover the product.
■ You must return the product (postage pre-paid by GE
Appliances) to GE Applaince’s recovery center before
a replacement unit will be provided. Please include a
description of the defect.
■ You should receive your replacement product within
7 to 10 business days after your unit is received.
In Order to Make a Warranty Claim During the Remainder of the One-Year Warranty:
Staple your receipt here. Proof of the original purchase date is needed to obtain service under the warranty.

14 49-5000427 Rev. 0
Printed in the United States
Consumer Support
CONSUMER SUPPORT
GE Appliances Website
Have a question or need assistance with your appliance? Try the GE Appliances Website 24 hours a day, any day
of the year! You can also shop for more great GE Appliances products and take advantage of all our on-line support
services designed for your convenience. In the US: GEAppliances.com
Register Your Appliance
Register your new appliance on-line at your convenience! Timely product registration will allow for enhanced
communication and prompt service under the terms of your warranty, should the need arise. You may also mail in
the pre-printed registration card included in the packing material. In the US: GEAppliances.com/register
Schedule Service
Expert GE Appliances repair service is only one step away from your door. Get on-line and schedule your service at
your convenience any day of the year. In the US: GEAppliances.com/service or call 800.432.2737 during normal
business hours.
Extended Warranties
Purchase a GE Appliances extended warranty and learn about special discounts that are available while your
warranty is still in effect. You can purchase it on-line anytime. GE Appliances Services will still be there after your
warranty expires. In the US: GEAppliances.com/extended-warranty or call 800.626.2224 during normal
business hours.
Remote Connectivity
For assistance with wireless network connectivity (for models with remote enable),visit our website at
GEAppliances.com/connect or call 800.220.6899 in the US.
Parts and Accessories
Individuals qualified to service their own appliances can have parts or accessories sent directly to their homes
(VISA, MasterCard and Discover cards are accepted). Order on-line today 24 hours every day.
In the US: GEApplianceparts.com or by phone at 877.959.8688 during normal business hours.
Instructions contained in this manual cover procedures to be performed by any user. Other servicing
generally should be referred to qualified service personnel. Caution must be exercised, since improper
servicing may cause unsafe operation.
Contact Us
If you are not satisfied with the service you receive from GE Appliances, contact us on our Website with all the
details including your phone number, or write to:
In the US: General Manager, Customer Relations | GE Appliances, Appliance Park | Louisville, KY 40225
GEAppliances.com/contact

Escriba los números de modelo
y serie aquí:
# de Modelo _____________
# de Serie _______________
Puede encontrar estos números en
una etiqueta en la parte atrás del
deshumedificador.
GE es una marca registrada de General Electric Company. Fabricado bajo licencia de marca.
MANUAL DEL
PROPIETARIO
DESHUMEDIFICADOR
49-5000427 Rev. 0 09-19 GEA
APEL50
APEW50
APER50
INFORMACIÓN
DE SEGURIDAD ...................3
INSTRUCCIONES DE OPERACIÓN
Controles .............................4
Cómo funciona el deshumedificador .....5
Descongelado automático ..............5
Selección del lugar adecuad ............5
Cómo desechar el agua acumulada ......6
Nivel de agua .........................7
Funcionamiento del Balde ..............7
CUIDADO Y LIMPIEZA
Rejilla y gabinete ......................8
Tanque de agua .......................8
Filtre de aire ..........................8
Filtro del Cubo ........................9
Almacenamiento.......................9
CONSEJOS PARA LA SOLUCIÓN
DE PROBLEMAS .................10
CONSEJOS PARA LA SOLUCIÓN
DE PROBLEMAS .................10
ESQUEMA ELÉCTRICO..........12
GARANTÍA LIMITADA ..........13
AYUDA AL CLIENTE ............14

249-5000427 Rev. 0
GRACIAS POR HACER QUE GE APPLIANCES SEA PARTE DE SU HOGAR.
Ya sea que haya crecido usando GE Appliances, o que ésta es su primera vez, nos complace
tenerlo en la familia.
Sentimos orgullo por el nivel de arte, innovación y diseño de cada uno de los electrodomésticos de
GE Appliances, y creemos que usted también. Entre otras cosas, el registro de su electrodoméstico
asegura que podamos entregarle información importante del producto y detalles de la garantía
cuando los necesite.
Registre su electrodoméstico GE ahora a través de Internet. Sitios Web y números telefónicos útiles
están disponibles en la sección de Soporte para el Consumidor de este Manual del Propietario.
También puede enviar una carta en la tarjeta de inscripción preimpresa que se incluye con
el material embalado.

49-5000427 Rev. 0 3
INFORMACIÓN IMPORTANTE DE SEGURIDAD
LEA TODAS LAS INSTRUCCIONES ANTES DE USAR ESTE ELECTRODOMÉSTICO
INFORMACIÓN DE SEGURIDAD
LEA Y GUARDE ESTAS INSTRUCCIONES
ADVERTENCIA Por su seguridad, se debe seguir la información en este manual para minimizar el riesgo de
incendios, descargas eléctricas o lesiones personales.
■ Use este electrodoméstico solamente para el propósito
determinado según se describe en este Manual del
propietario.
■ Este deshumedificador debe instalarse correctamente y
conectado a tierra de acuerdo con las instrucciones de este
manual antes de su uso.
■ Nunca opere este deshumedificador en un área en la que
es posible que se acumule agua. De encontrarse en estas
condiciones, por su seguridad, desconecte el suministro de
corriente eléctrica antes de pisar sobre
el agua.
■ Nunca desenchufe su deshumedificador tirando del cable
eléctrico. Siempre agarre firmemente el enchufe y tire de él
directamente hacia afuera.
■ Reemplace inmediatamente todos los cables eléctricos
que se hayan pelado o que se hayan dañado de alguna
otra manera. Un cable de corriente dañado no debe
repararse, sino que debe ser sustituido por uno nuevo que
se adquiera del fabricante. No use un cable eléctrico que
muestre evidencias de deterioro, o daños de abrasión en
su superficie en alguno de sus extremos.
■ Si el receptáculo no coincide con el enchufe, un electricista
calificado debe reemplazar el receptáculo.
■ Si el CABLE DE ALIMENTACION está dañado, deberá ser
reemplazado por el fabricante, su agente de servicios o
una persona con calificación similar a fin de evitar riesgos.
■ El electrodoméstico deberá ser instalado de acuerdo con
las regulaciones de cableado nacionales.
■ Apague el control y desenchufe su deshumedificador antes
de hacer cualquier reparación o limpiar.
■ GE Appliances no está no apoya que se le proporcione
ningún servicio al deshumedificador. Vehementemente
recomendamos que usted no intente proporcionar servicio
al deshumedificador usted mismo.
■ Por su seguridad, no almacene ni use materiales
combustibles, gasolina u otros vapores o líquidos
inflamables en la proximidad de éste o algún otro
electrodoméstico.
■ No use el deshumedificador en exteriores.
■ Este deshumedificador está diseñado exclusivamente para
aplicaciones residenciales de interior. No debe usarse para
aplicaciones comerciales ni industriales.
■ Estos Sistemas Deshumedificadores R410A requieren
que los contratistas y técnicos utilicen herramientas,
equipamiento y normas de seguridad aprobadas para
su uso con este refrigerante. NO utilice equipamiento
certificado sólo para refrigerante R22.
■ Este electrodoméstico puede ser usado por personas con
capacidades físicas, sensoriales o mentales reducidas o
con falta de experiencia y conocimiento, si les fue dada
supervisión o instrucción relacionada con el uso de este
electrodoméstico de una forma segura y entienden los
riesgos involucrados.
ADVERTENCIA USO DE PROLONGADORES
RIESGO DE INCENDIO. Podría ocasionar lesiones graves o la muerte.
■ NO use prolongadores con este Deshumidificador.
■ NO use protectores contra picos de corriente ni
adaptadores para múltiples tomacorrientes con este
Deshumidificador.
COMO CONECTAR LA ELECTRICIDAD
Bajo ninguna circunstancia, corte o remueva la tercera púa
(tierra) del cable eléctrico. En pos de la seguridad personal,
este electrodoméstico debe siempre conectarse a tierra.
NO USE un enchufe adaptador con este aparato.
El cable eléctrico de este electrodoméstico está equipado
con un enchufe de tres púas (tierra) que combina con
un tomacorriente estándar de tres tomas de pared para
minimizar la posibilidad de una descarga eléctrica.
Pida a un técnico que inspeccione el tomacorriente y el
circuito para cerciorarse de que el tomacorriente está
conectado a tierra de la manera apropiada.
Donde exista un tomacorriente de dos tomas, es su
responsabilidad y obligación personal hacer que dicho
tomacorriente sea reemplazado por uno de tres tomas con
conexión a tierra.
El deshumedificador debería siempre estar conectado
a un tomacorriente individual con su circuito de voltaje
correspondiente.
Esto proporciona el mayor rendimiento y además evita
que los circuitos del resto de la casa se sobrecarguen, lo
cual podría causar incendios por el sobrecalentamiento del
cableado.
INFORMACIÓN SOBRE CÓMO RECICLAR
Para acceder a información sobre como reciclar sus electrodomésticos, ingrese a www.geappliances.com/recycling.

449-5000427 Rev. 0
INSTRUCCIONES DE OPERACIÓN
Controles
Controls
NOTA: Cuando el recipiente está lleno o es retirado, los controles
no pueden ser ajustados.
1. Power Pad
Presione para encender o apagar el deshumedificador.
2. Temporizador del filtro (Filter Timer)
Después de 250 horas de operación, se encenderá la luz
indicadora de Clean the Filter (Limpieza de filtro) para recordarle
que debe limpiar el filtro. Quite el filtro y límpielo.
Presione para apagar la luz de Clean the Filter (Limpieza de
filtro) light. Ver la sección Cuidado y limpieza.
3. Botones para el Control de humedad
(Humidity Set Control)
La humedad se puede controlar a niveles de entre 35%
HR (humedad relativa) – 80% HR (humedad relativa) en
incrementos del 5% o con NS para un funcionamiento continuo.
Para configurar la unidad en operación continua, presione la
flecha hacia abajo hasta que se observe NS en la pantalla.
NOTA: Si se selecciona NS (Nonstop), el deshumedificador
funcionará en forma continua en la configuración máxima de
deshumedificación hasta que se llene el tanque.
Si desea aire más seco, presione el botón – y seleccione un
valor porcentual más bajo (%).
Si desea aire más húmedo, presione el botón + y seleccione
un valor porcentual más alto (%).
Cuando use por primera vez el deshumedificador, coloque
el control del deshumedificador a 45% ó 50%. Permita
que transcurran por lo menos 24 horas para que el
deshumedificador alcance el nivel de humedad. Si el
aire aún está más húmedo de lo deseado, ajuste el nivel
de humedad a un nivel menor o seleccione el botón de
funcionamiento continuo (Nonstop) para obtener una máxima
deshumidificación.
4. Pantalla
Muestra el % del nivel de humedad programado durante la
configuración, luego muestra el % del nivel de humedad real de
la habitación (con una precisión de +/– 5%).
5. Boton de velocidad del ventilador (Fan Speed)
Controla la velocidad de circulación del aire.
Presione para seleccionar la velocidad del ventilador en alta
(High), medio (Medium) o bajo (Low).
Coloque el control del ventilador a alta (High) velocidad para
lograr remover la mayor cantidad
de humedad. Cuando la humedad haya sido reducida y usted
prefiera una operación más tranquila, coloque el control del
ventilador a medio (Medium) o bajo (Low) velocidad.
6. Retardo en apagado (Delay Off)
Mientras el deshumedificador se encuentra en funcionamiento,
presione este botón para que se apague automáticamente a las
2 horas o a las 4 horas.
7. Bomba
Activa la función de la bomba interna. Presione durante 3
segundos para activar la bomba interna para el retiro automático
del condensado. La luz indicadora Pump On (Bomba
Encendida) titilará y luego permanecerá´iluminada una vez
completados los 3 segundos.
Presione para desactivar la bomba.
Otras funciones
Luz de Recipiente Vacío
Este indicador se ilumina cuando el tanque esté lleno y
debera vaciarse, o cuando el recipiente se remueva o no esté
colocado en la posición correcta.
Alarma (Alarm)
Si el tanque se encuentra lleno o no está en su lugar por más
de tres minutos, sonará una alarma durante 10 segundos para
recordarle de vaciar y volver a colocar el tanque.
Apagado automático (AUTO SHUT OFF)
El Interruptor de control de nivel de agua apaga el
deshumedificador cuando el tanque esté lleno, o cuando el
tanque no esté presente o no esté colocado en una posición
apropiada. NOTA: El ventilador seguirá funcionando durante
aproximadamente 3 minutos después de quitar el tanque
Descongelado automático (AUTO DEFROST)
Cuando se acumule escarcha en los serpentines
evaporadores, el compresor se apagará, y el ventilador
continuará funcionando hasta que la escarcha desaparezca.
Pérdida de energía (POWER OUTAGE)
En caso de la pérdida de la energía o interrupción, la unidad
reiniciará automáticamente, en las configuraciones usadas por
última vez, una vez la energía sea restablecida.
5
Nonstop
Humidity %
On
Filter
Power -+FanPump
Hold 3 Sec To Rest Hold 3 Sec
Requires Hose
Filter
Timer
Delay
Off
Empty
Pump
4 hour
2 hour
Medium
Low
High
La luz de Bucket Full
(Recipiente Lleno) indica
que éste deberá ser
vaciado o que no está en el
lugar correcto de la unidad
Luces indicadoras
de retardo en
apagado de 4
horas o 2 horas
Luz indicadora de
funcionamiento de
operación continua
Encendido Activado
luz indicadora de
encendido
Luz indicadora de
limpieza de filtro
Luces indicadoras de
velocidad de ventilador
alta, media y baja
La luz indicadora
Pump (Bomba)
indica que la bomba
está funcionando

49-5000427 Rev. 0 5
Cómo usar el deshumedificador
Selección del lugar adecuado
Cómo funciona el deshumedificador
La humedad en el aire pasa por un serpentin
deshumedificador. La humedad en el aire se condensa en
este serpentin y se drena hacia el tanque (o a través de la
manguera y luego través del drenaje).
El aire limpio y seco pasa luego por el condensador donde
es calentado y desechado de regreso al medio ambiente a
través de la parrilla.
Es normal que el aire en los alrededores se caliente un
poco conforme el deshumedificador funciona.
Descongelado automático
Cuando se acumule escarcha en los serpentines
evaporadores, el compresor se apagará, y el ventilador
continuará funcionando hasta que la escarcha
desaparezca.
Cuando el evaporador se descongele, el compresor o el
ventilador se encenderá automáticamente y el proceso de
deshumedificación continuará.
INSTRUCCIONES DE OPERACIÓN
Cuando se disponga a usar el deshumedificador por primera vez, permita que la unidad opere de manera
continua por 24 horas.
El deshumedificador ubicado en un sótano tendrá poco o
ningún efecto en secar el aire dentro areas adjacentes de
almacenamiento, como un armario, por ejemplo, al menos que
exista una circulación adecuada de aire hacia en interior y
hacia el exterior de dicha área.
■ No use el deshumedificador en exteriores.
■Este deshumedificador está diseñado exclusivamente para
aplicaciones residenciales
de interior. No debe usarse para aplicaciones comerciales
ni industriales.
■Coloque el deshumedificador en un piso firme y nivelado
que sea lo suficientemente fuerte para soportar la unidad
cuando la cubeta esté llena de agua.
■ Deje por lo menos 18 pulgadas de espacio libre alrededor
de la unidad para que exista una buena circulación de aire.
■Coloque el deshumedificador en un área en la que la
temperatura no sea inferior a 41 °F (5 °C) ni superior a 90°F
(32°C). Los serpentines pueden escarcharse en ambientes
con temperaturas inferiores a 41 °F (5 °C), lo cual puede
reducir su rendimiento.
■ El rango sugerido o la humedad relativa está entre 30% y
90%.
■ Use el deshumedificador en áreas como la cocina, cuartos
de lavado, baños, y en áreas donde exista humedad
excesiva. NOTA: Coloque el deshumedificador lejos la
secadora de ropa.
■ Use el deshumedificador para evitar daños causados por
la humedad en lugares donde guarde libros o artículos de
valor.
■ Use el deshumedificador en el sótano para ayudar a
prevenir los daños causados por la humedad.
■El deshumedificador debe usarse en áreas cerradas para
mayor efectividad.
■Cierre todas las puertas, ventanas y otras aberturas
hacia el exterior de la habitación en donde esté el
deshumedificador.
NOTA: El deshumedificador tiene ruedas para ayudarle
a colocarlo en distintos lugares, pero debe rodarse en
superficies firmes y plantas. No intente rodarlo sobre objetos o
sobre una alfombra.
Above Below
Correct Wrong
at least 18 inches
at least 18 inches
SI NO
Por
debajo
de 41 °F
(5°C)
Por
encima
de 41°F
(5°C)
18 pulgadas mín.
18 pulgadas mín.

649-5000427 Rev. 0
Cómo usar el deshumedificador
Cómo desechar el agua acumulada
Hay 2 formas de desechar el agua acumulada
Use el tanque. Cuando usted saque el tanque de su lugar, la
unidad se apagará. Vacíe y reinstalelo.
IMPORTANTE: No use el manguera si usa el tanque para
recoger agua. Si el manguera está conectada, el agua caerá al
piso en lugar de caer dentro del tanque.
NOTAS:
■ No retire el balde con el deshumedificador en
funcionamiento o si recién se apagó. Esto puede hacer que
el agua gotee del recipiente de drenaje.
■ El tanque debe estar en su lugar y bien sujeto para que el
deshumedificador funcione.
Use una manguera. El agua puede desecharse
automáticamente hacia un drenaje en el piso si usted conecta
el tubo de drenaje con boquilla de la unidad a una manguera
para agua de jardín (no incluida).
1. Saque el tanque del frente de la unidad.
2. Abra la tapa de drenaje sobre el lado de
3. Enrosque una manguera para jardín (no provista) en la
boquilla, cut to length, y diríjala al drenaje de piso.
4. Vuelva a colocar el tanque en la unidad.
NOTA: El tanque debe estar en su lugar y bien sujeto para que el
deshumedificador funcione.
Use la bomba interna. El agua puede ser vaciada de forma
automática en una ubicación remota, adhiriendo la manguera incluida
de la bomba.
1. Adhiera la manguera de la bomba al conector de la manguera,
presionando el accesorio de la tubería en el conector hasta que
quede colocada correctamente (usted no debería poder retirar la
manguera al empujar).
2. Posicione la descarga de la manguera en la ubicación deseada.
3. Asegúrese de que la bomba esté activada. Para activar la bomba,
mantenga presionado el botón Pump On/Off (Bomba Activada/
Desactivada) durante 3 segundos. La luz indicadora Pump On
(Bomba Encendida) titilará y luego permanecerá iluminada una vez
completados los 3 segundos.
4. Vuelva a colocar el cucharón en la unidad.
La bomba no comenzará a eliminar agua hasta que el balde esté lleno.
Después de que el botón de la bomba se haya activado al mantener
presionado durante 3 segundos, la bomba permanecerá en espera.
Cuando el cucharón está lleno, la bomba comenzará a eliminar agua
automáticamente y se detendrá cuando se vacíe el cucharón. Este
ciclo continuará hasta que se desactive el botón de la bomba.
IMPORTANTE: Asegúrese de que la manguera para condensado esté
correctamente conectada y que no esté retorcida, inclinada ni fisurada,
ya que esto puede hacer que caiga agua al piso. El cubo también
debe estar completamente apoyado para que la bomba funcione de
forma correcta. No utilice la máquina si la temperatura ambiente es de
32ºF o inferior.
NOTAS:
■ La altura máxima de elevación es de 16 pies.
■ El cubo debe estar correctamente colocado y apoyado de forma
segura para que el deshumidificador y la bomba funcionen.
Asegúrese de instalar la manguera (incluida) antes de activar la
bomba.
INSTRUCCIONES DE OPERACIÓN
Siempre cerciórese de que la tanque de agua esté asegurada en su lugar dentro del deshumedificador.
Manija
Recipiente
drain hose
nozzle
Manguera
de Desagüe
Manguera
de Desagüe