GE GFDS250EF User manual

Marcone 2014 MSA
Training
GE Mission 1
Front Load Dryer
1

GE Front Load Dryer
MODELS
GFDS250EF/GF GFDS255EF/GF
GFDS260EF/GF GFDS265EF/GF
GFDS360EF/GF GFDS365EF/GF
GHDS370EF/GF GHDS375EF/GF
GFDR480EF/GF GFDR485EF/GF
Note:
“0” models are White
“5” models are either Metallic Carbon
or Ruby Red
(GFDR480GF)
2

Warranty
3

Nomenclature
GFDR480GFWW
G - Brand: G = GE P = Profile
F - Configuration: F = Frontload
D - Product: D = Dryer
R - Key Feature: S = Standard R = Riser
480 - Options Package
E - Heater Type: E = Electric G = Gas
F - Model Year Designator
WW - Color: WW = White MC = Metallic Carbon
RR = Ruby Red
4

Features (480 Series)
GFDR480EF/GF GFDR485EF/GF
• 8 0 DOE
• Chrome Door
• Chrome Knob with Rubber Grip
• Chrome UI Trim
• Steam
• 12 Cycles
• 5 Dryness Levels
• eDry
• eMonitor
• Detangle
• Interior LED Light
• Dryer Rack
• Integrated Riser
• DSM (RJ45) Capable
Available in White, Metallic Carbon & Ruby Red
Weight 183 lbs Height: 47" Width: 28" Depth: 34-3/8"
5

Model / Serial Plate Location
The model / serial number plate is located behind the door, just under
the drum opening
6

Mini Manual (Tech Sheet) Location
The mini-manual is taped to the backside of the control panel along with
the UI/IMC board
Control escutcheon has to be removed to access
7

RJ45 Connector Location
The RJ45 connector is located
on the top rear of the machine
In some areas, this will allow
consumers to connect to their
local energy grid via DSM
(demand side management)
DSM is used to better control
energy usage throughout the
home
8
Rear view of dryer

Feature Definitions Steam
Steam - A mist of room temperature water sprayed into the drum
Steam is used on the "Steam Dewrinkle" and the "Steam Refresh" cycles
9
Steam Dewrinkle - Used for loads left in the dryer for an extended period of time
Steam Re resh - For slightly wrinkled dry garments Significantly reduces wrinkles
on up to 5 garments After the Steam Refresh Cycle, the unit will beep and display
“0:00 ” If the unit is not turned off or if the door is not opened, the dryer will
continue to tumble for 30 minutes At the end of 30 minutes, it will display “0:00”
and the cycle will be complete

Feature Definitions eDry
•eDry - Reduces the total energy consumption by adjusting certain heat
settings
•eDry is selected by pressing the eDry Button
Machine settings when eDry is selected:
Dry Temp = Low
Extended Tumble = eDry is Disabled
Sanitize = eDry is Disabled
10

Feature Definitions eMonitor
eMonitor - Visual display of the
energy
use of the appliance
eMonitor Ranges:
Good (1 light) to Best (5 lights)
11

Feature Definitions – Detangle(1)
12
Detangle - Reduces tangling, dries more evenly, and improve drying times
by periodically reversing drum rotation direction
Detangle is selected by pressing the Detangle button

Feature Definitions – Detangle(2)
13
•When the Detangle feature is selected, the control will execute a reversing
tumble profile
•When the Detangle feature is not selected, the control will execute a Non-
reversing tumble profile
•When the Detangle Option is changed during the Run State, the control will stop
the drum, and start the new Tumble Profile
•There is a delay of six seconds before reversing the Drum Motor to allow for an
empty/nearly empty drum to stop to ensure the drum motor has stopped to
ensure motor reversal
NOTE: No heat will be applied during the clockwise tumbling steps of the tumble
profile
NOTE: The Mist Valve will not be energized during the clockwise tumbling steps of
the tumble profile

Feature Definitions – Dryness levels
14
•Dryness Level - Provides an option for consumers to end the dry cycle when the
clothes reach a certain moisture content
•The dryness level is set by pressing the Level button
Available Dryness Levels:
Damp
Less Dry
Dry
More Dry
Extra Dry

Feature Definitions Integrated Riser
Integrated Riser - Adds an additional
7" of height to the unit
15

Disassembly Control Panel Removal(1)
Remove the cycle selector knob by pulling it forward
16

Disassembly Control Panel Removal(2)
Remove the cycle selector knob retainer by pulling it forward
17

Disassembly Control Panel Removal(3)
Remove the T20 Torx Head screw securing control panel to
frame
18

Disassembly Control Panel Removal(4)
Lift the control panel straight up to disengage the mounting
tabs.
19

Disassembly Control Panel Removal(5)
Multiple cables / plugs connect the UI/IMC board to the
electromechanical components of the dryer
20