GE SBF Wide Beam Floodlight User manual

GEH-3873H
SBF®WideBeamFloodlight
SBNNarrowBeamFloodlight
WithHIDMediumBaseSocket
INSTRUCTIONS
READTHOROUGHLYBEFOREINSTALLING
GENERAL
This floodlight has been designed for use in outdoor
applications and should not be installed in areas of
limited ventilation or in high ambient temperature
enclosures. Best results will be obtained if installed and
maintained according to the following
recommendations.
UNPACKING
This luminaire has been packed so that no parts
should have been damaged during transit. Inspect to
confirm.
INSTALLATION
This floodlight is provided with a pre-wired 1/2-inch
NPT threaded swivel fitting for mounting to standard
wiring boxes or conduit (locknuts not provided). Contact
your local GE electrical distributor for information
regarding availability of accessories for other mounting
options; cross-arm mounting adaptor, flat surface adaptor
for mounting over 4-inch J-box, swivel/slipfitter adaptor
for mounting on 1-1/2-inch to 2- inch pipe and trunnion
mounting adaptor (threaded portion of swivel fitting
must be removed to install trunnion adaptor).
WARNING
Risk of electric shock
•Turn power off before servicing
–see instructions
CAUTION
Unit will fall if not installed properly
•Follow installation instructions
NOTE: THE FLOODLIGHT IS INTENDED TO BE
MOUNTED IN THE ORIENTATION SHOWN
ABOVE. DO NOT MOUNT OR OPERATE IN AN
INVERTED POSITION SUCH THAT LAMP IS
OPERATING IN A BASE-UP ORIENTATION AS
WATER CAN ENTER THE FIXTURE IF OPERATED
IN A WET ENVIRONMENT.
These instructions do not purport to cover all details or variations in equipment nor to provide for every possible contingency to be met in connection with installation, operation
or maintenance. Should further information be desired or should particular problems arise which are not covered sufficiently for the purchaser’s purposes, the matter should be
referred to GE Lighting Solutions.
gGE
Lighting Solutions
OK DO NOT INVERT

35-201578-91 (1/00)
NOTE: REMOVE SCREWS FROM WEEP HOLES IN
BACK OF THE FIXTURE WHEN FLOODLIGHT IS
AIMED UP (ABOVE HORIZONTAL). FAILURE TO
DO SO COULD RESULT IN WATER BEING
TRAPPED INSIDE FIXTURE.
Use only lamps specified on nameplate. Observe
lamp manufacturer’s recommendations and
restrictions on lamp operation, particularly ballast
type, burning position, etc.
Lamp Tightness – Medium Base Lamp: The lamp
should be tightened to a light firmness sufficient to
depress the center contact.
CAUTION: FOR METAL HALIDE VERSIONS OF THE
SBF WITH PHOTOCONTROLS AIMING IS RESTRICTED
BELOW 45 DEGREES. AIMING MORE THAN 45
DEGREES BELOW HORIZONTAL MAY LEAD TO
OVERHEATING OF FIXTURE COMPONENTS, VOIDING
UL LISTINGS AND MANUFACTURER'S WARRANTY.
Make all electrical connections in accordance with
the National Electrical Code and any applicable
local code requirements.
Verify that supply voltage is correct by comparing
it to nameplate.
Do not remove insulated connectors from wires
not needed for required voltage connection.
When changing voltage on reconnectable units,
move only the lead with the insulated connector.
IF SINGLE VOLTAGE:
CAUTION
Riskofburn
•Allow lamp/fixture to cool before
handling
WARNING
Riskofburn
•Do not touch operating luminaire
All single voltage ballasts are pre-wired such that
user need only connect the supply conductors.
IF MULTIVOLT: (120/208/240/277 volts)
Connect the ballast lead with the insulated terminal
to the desired voltage terminal as indicated on the
ballast terminal nameplate.
IF MULTIWATT:
Multiwatt ballasts are available in various combina-
tions of wattage. See wiring instructions on wiring
tag inside the luminaire.
MAINTENANCE
It will occasionally be necessary to clean the
luminaire to maintain light level. Frequency of cleaning
will depend on ambient dirt level and minimum light
level which is acceptable to user. Lens door should be
washed in a solution of warm water and any mild,
non-abrasive household detergent, rinsed with clean
water and wiped dry. Should optical assembly become
dirty on inside, wipe reflector and clean lens door in
above manner and replace any damaged gasket.
gGE Lighting Solutions is a subsidiary of the General Electric Company. Evolve and other trademarks belong to GE Lighting Solutions. The GE brand and logo are trademarks of the General Electric Company.
© 2011 GE Lighting Solutions. Information provided is subject to change without notice. All values are design or typical values when measured under laboratory conditions.
GE Lighting Solutions • 1-888-MY-GE-LED • www.gelightingsolutions.com
16943533----888
AIMING LIMITATIONS FOR METAL HALIDE UNITS