GE Built-In Dishwasher User manual

INSTALLATION INSTRUCTIONS FOR YOUR NEW
24"BUILT-INOVEN
Before you begin -Read these instructions completely and carefully.
IMPORTANT -Save these instructions for local inspector's use.
IMPORTANT -OBSERVE ALL GOVERNING CODES AND ORDINANCES.
Note to Installer- Be sure to leave these instructions with the Consumer.
Note to Consumer- Keep these instructions with your Use and Care Guide for future reference.
ATTENTION INSTALLER -All ovens must be hard wired (direct wired) into an approved junction
box. A "plug and receptacle" is not permitted on these products.
Be sure your oven is installed properly by a qualified
installer or service technician.
•Be sure the oven is securelyinstalledin acabinet
that is firmly attached to the house structure.
Weight on the oven door could cause the oven to
tip, resulting in serious personal injury or death.
Never allow anyone to climb, sit, lean, stand or
hang on the oven door.
• The wall coverings, countertop and cabinets
around the oven should be able to withstand
the heat (up to 200°F) generated by the oven.
•1/8" Drill Bit •Ruler
•Electnc or Hand Dr/// •Handorsabersaw
• Flat Blade screwdriver • Pencil
Cabinet space must be provided to enclose the
recessed part of your built-in oven. SINGLE
OVEN INSTALLATION i See Figure 1 for
all necessary dimensions. DOUBLE OVEN
INSTALLATION iSee Figure 2 for all necessary
dimensions. It is best to make a template to insure
accurate cutting. Place the bottom of the template on
a level base line, above the floor. See dimension E in
Figure 1 (Single Oven) or Figure 2 (Double Oven).
It is important that the oven be installed at or above
the minimum height specified. The unit has been
tested and approved, in accordance with safety
standards, at this height.
31-10658 (456 JR)
_AUTION:Theelectricalpowertothe 1
ovensupplylinemustbeshutof while
connectionsarebeingmade.Failuretodo
socouldresultinseriousinjuryordeath.
This appliance must be supplied with theproper voltage
and frequency, and connected to an individual, properly
grounded branch circuit, protected by a circuit breaker
or fuse having amperage as noted on rating plate.
(Rating plate is located on front frame.)
Rating _ _
Plate
Location _ _--_
........... '_..
i • i
Werecommend you have theelectrical wiring and hookup
ofyouroven done bya qualified electn'ctan.Aftenhstallation,
have the electrician show you where your main oven
disconnect is located.
Check with your local utilities for electrical codes
whlbh apply inyour area.Faffuretowireyour ovenaccording
to governing codes could result in a hazardous condition.
If there are no local codes, your oven must be wired and
fused to meet the requirements of the National Electrical
Code, ANSI/NFPA No. 70-Latest Edition. You can get a
copy of the National Electrical Code, ANSI/NFPA
NO. 70-Latest Edition by wn'ting:
National Fire Protection Association
Batterymarch Park
Quincy, MA 02269
Effective January 1, 1996, the National Electrical Code
requires that new, but not existing, construction util/2e a
4 conductor connection toan electric oven. Wheninstalling
an electric oven in new construction, a mobile home,
recreational vehicle or an area where local codes prohibit
grounding through the neutral conductor, follow the
instructions in NEW CONSTRUCTION AND FOUR-WIRE
CORD CONNECTION KIT
You must use a three-wire, single-phase A.C. 208Y/120
Volt or 120/240 Volt, 60 Hertz electrical system. If you
connect toaluminum wl?ing,properly installed connections
approved for use with aluminum wiring must be used.

Fig. 1 -- SINGLE OVEN
NOTE. Locate an approved junction box in the
suggested location, a minimum of 23 7/8" above the
runners.
Be sure the oven support is solid enough to support
90 pounds. Also be sure the oven support is level
and straight. There is no way to level the oven
after installation.
/f a solid bottom is used instead of runners, a 6" x 10"
rectangle must be cut out of the bottom (See Fig. 1)
for optimum performance and proper air circulation.
DIMENSIONS
A. Cabinet Width
B. Cutout Width
C. Cutout Height
D. Cutout Depth
E. Cutout Location
H. Overall Height
WOverall Width
24 _'
22 1/2"
27 5/8" Min. 28 1/8" Max.
23 1/2" Min.
32 1/2"
28 1/4"
23 3/4"
Equivalent Runners
for over{ap
edges
to adjacent corners, drawers, or wails, etc
Fig. 2 -- DOUBLE OVEN
NOTE. Locate an approved junction box in the
suggested /ocaton, am n mum of 48 'above the runners.
Be sure the oven support is solid enough to support
155 pounds. Also be sure the oven support is level
and straight. There is no way to level the oven after
installation.
/f a solid bottom is used instead of runners, a 6" x 10"
rectangle must be cut out of the bottom (See Fig. 2)
for optimum performance and proper air circulation.
DIMENSIONS
A. Cabinet Width
B. Cutout Width
C. Cutout Height
D. Cutout Depth
E. Cutout Location -
H. Overall Height
WOverall Width
24" Min.
22 1/2"
48 1/8"
23 1/2" Min.
12 3/4" Min.
48 3/4"
23 3/4"
2" x 4" OR
9" RUNNERS
i__ MJN .__ iEQUIVALENT
_6,\
16"
2i" _
MIN,
2
-_ 20- MINIMUM CLEARANCE TO
ADJACENT CORNERS, DRAWERS.
OR WALLS, ETC.
JUNCTION
BOX

IMPORTANT."Removea// packing
materia/ and /iterature from J
the oven before connectingany
e/ectrica/supp/ies.
,
2. De-energize oven branch circuit.
With oven in front of cabinet opening, connect
flexible power cable to the junction box in such
a mannerthatitwillhang down in a naturalloop
against the left side of the back wall when the
oven is installed. Do not shorten this flexible
power cable. The flexible conduit connector
must be securely attached to the junction box
and the flexible conduit must be securely
attached to the connector. If the flexible conduit
will not fit within the connector, do not install
the oven until a connector of the proper size is
obtained.
All new construction, mobile homes, recreational
vehicles and installations where local codes do
not allow grounding through neutral require a four-
conductor branch circuiL For existing construction,
athree-conductor branch circuit connection may
be used.
NOTE 1"0 £/..£(_1"Rr/c/A.N; The three power
leads supplied with this appliance are U.L.
recognized for connection to larger gauge
household wiring. The insulation of these three
leads is rated at temperatures much higher than
the temperature rating of household wiring. The
current carrying capacity of a conductor is
governed by the temperature rating of the insulation
around the wire rather than the wire gauge alone.
When connecting to a3-conductor branch
circuit, if local codes permit, connect the oven
bare conductor with the crimped neutral (white)
lead to the branch circuit neutral (white or gray
in color), the oven red lead to the branch circuit
red lead and the oven black lead to the branch
circuit black lead in accordance with local
codes.
_WARNING:
/mproper connection of a/uminum
housewiringto these copper/earls
canresu/tin an e/ectrica/hazardor
fire. Use on/y connectorsdesigned
for joining copper to a/uminum
and fo/Iow the manufacturer's
recommendedprocedurec/ose/y.
•When installing in a new construction, or
•When installing oven in a mobile home orrecreational
vehicle, or
• When local codes do notpermitgrounding through
neutral:
1. Cut the neutral (white) lead from the crimp. Restrip
the neutral (white) lead to expose the proper length
of conductor.
2. Attach the appliance grounding lead (green or
bare copper) to the residence grounding conductor
(green or bare) in accordance with local codes. If
the residence grounding conductor is aluminum,
see WARNING note.
3. Connect the oven neutral (white) lead to the branch
circuit neutral (white or gray) in accordance with
local codes.
4. Connect the oven red lead to the branch circuit red
lead and the oven black lead to the branch circuit
black lead in accordance with local codes. If the
residence red and black or white leads are
aluminum conductors, see WARNING note. 3

To remove the oven door:
1. Open the door to the stop position (see Fig. 3A).
2. Grasp the door at each side and lift up and off the
hinges (see Fig. 3B).
1. Hold the door over the hinges with the slots at
the bottom edge of the door lined up with the
hinges.
2. Slide the door down onto the hinges as far as
it will go and close the door.
/
/
/
i
3. Putthe oven into the cabinet and use a 1/8"drill
bit to drift holes in the cabinet front through the
holes in the oven trim.
4. Secure the oven in the cabinet with the screws
provided.
5. Thelowertrimshouldbemountedtothebottom
of the oven frame with the 3 screws provided.
The lower front trim is packed separately and
should be added after the oven is installed. The
oven door must be removed to install the
lower trim.
STOPPOSITION
Fig. 3A
HINGE
Fig. 3B
Thetrim prov/descoo/ingairentryinto
cabinetthrough the bottomopening.
Thebottomopeningshouldneverbe
blocked. See Fig. 3B.
Recycled Paper
4-- Printedin theUnitedStates--