GE GDSL0KCXLS User manual

TOOLS YOU WILL NEED
Thin-blade Screwdriver
Installation Reversing the
Instructions
Door Swing
(Single Door Refrigerator Mo els only)
Questions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: ge.com
In Cana a, call 1.800.561.3344 or Visit our Website at: www.geappliances.ca
1200D9512P002 31-46127 01-08 JR
IMPORTANT NOTES
When reversing the door swing:
NOTE: Door swing is not reversible on stainless steel
models.
•Read the instructions all the way through before
starting.
•Parts are included in the door hinge kit.
•andle parts carefully to avoid scratching paint.
•Set screws down by their related parts to avoid
using them in the wrong places.
•Provide a non-scratching work surface for the doors.
IMPORTANT: Once you begin, do not move the cabinet
until door-swing reversal is completed.
These instructions are for changing the hinges from the
right side to the left side—if you ever want to change
the hinges back to the right side, follow these same
instructions and reverse all references to left and right.
• Once door swing is finalized, ensure the logo badge is
properly aligned and permanently secured to the door
by removing the adhesive cover on the back side.
NOTE: A replacement logo badge is included
in the hinge kit.
Unplug the refrigerator from its electrical outlet.
Empty all oor shelves, inclu ing the airy
compartment.
Masking Tape
Adjustable Wrench 5/16″ Socket
Ratchet/Driver
Phillips Screwdriver
Torx T-20 Driver
REMOVE THE REFRIGERATOR DOOR
Tape the door shut with masking tape.
Remove the hinge cover on top of the
refrigerator door by carefully prying it
up with a putty knife, if necessary.
Using a 5/16″socket ratchet/driver, remove
the bolts securing the top hinge to the cabinet.
Then lift the hinge straight up to free the hinge
pin from the socket in the top of the door.
Carefully remove the door thimble from inside
the socket. This will be used again when
reinstalling the door on the other side.
1
A
B
C
D
inge Cover
Top inge
Door Thimble

TRANSFER CENTER HINGE BRACKET
Using a 5/16″socket ratchet/driver, remove the
bolts securing the center hinge to the cabinet.
Transfer the plug button and screw hole cover in
the hinge holes on the left side to the right side.
Install the new center hinge bracket from the
kit on the left side.
3
A
B
C
Installation Instructions
REMOVE THE REFRIGERATOR
DOOR (cont.)
Remove the tape and tilt the door away from
the cabinet. Lift the door off the center hinge
pin. Ensure that the plastic hinge pin thimble
remains on the hinge pin or inside door hinge
pin hole located in the bottom of the door.
Set the door on a non-scratching surface with
the inside up.
1
E
F
REMOVE CENTER HINGE
(For mo els without freezer oor)
Remove the hinge pin from the hinge bracket.
The hinge pin will be used again with the new
hinge bracket for the other side.
2
REMOVE THE FREEZER DOOR
(For mo els with freezer oor)
Tape the door shut with masking tape.
Remove hinge pin from hinge bracket. This will
be used again with the new hinge bracket for
the other side.
Remove the tape and tilt the door away from
the cabinet. Lift the door off the bottom hinge
pin.
2
A
B
C
2
REMOVE THE FREEZER DOOR
(For mo els with freezer oor) (cont.)
Remove the button plug from the left side of
the door. Remove the door thimble from the
right side of the door. Install the door thimble
into the hole on the left and the button plug
into the hole on the right.
Set the door on a non-scratching surface, with
the inside up.
2
D
E

INSTALL CENTER HINGE PIN
(For mo els without freezer oor)
Install the hinge pin into the new hinge bracket.
4
Installation Instructions
REMOVE BOTTOM HINGE AND
LEVELING LEG (For mo els with
freezer oor)
Using a 1/2″socket ratchet/driver, remove the nut
and hinge pin from the hinge bracket with leveling
leg. Using a 5/16″socket ratchet/driver, remove
the screws from the bottom hinge bracket. These
will be reinstalled on the other side.
Using a 5/16″socket ratchet/driver, remove
the screws from the leveling leg bracket on
the other side. These will be reinstalled on the
opposite side.
5
A
B
Bottom inge
Bracket
Leveling Leg
Bracket
INSTALL BOTTOM HINGE AND
LEVELING LEG (For mo els with
freezer oor) (cont.)
Using a 5/16″socket ratchet/driver, install the
hinge bracket with leveling leg on the left side
of the refrigerator. The pin will be toward the
outside of the refrigerator.
Using a 5/16″socket ratchet/driver, install the
leveling leg bracket on the right side of the
refrigerator.
6
C
INSTALL BOTTOM HINGE AND LEVELING
LEG (For mo els with freezer oor)
Using a 1/2″socket ratchet/driver, install the
hinge pin and nut in the opposite hole on the
hinge bracket with leveling leg.
6
A
3
TRANSFER REFRIGERATOR AND FREEZER
DOOR STOPS
Remove the door stop on right side of the bottom
of the door by removing the two screws.
Move the plastic hinge hole thimble to the
opposite hole.
Install the door stop on the left side, making
sure to line up the screw holes in the door stop
with the holes in the bottom of the door.
7
A
B
C
Bottom of Door (Right Side) Bottom of Door (Left Side)
A
B

REHANG REFRIGERATOR DOOR (cont.)
Insert the door thimble into the hinge hole
on top of the refrigerator door and then
insert the top hinge pin. Make sure the door
is aligned with the cabinet. Attach the hinge
to the top of the cabinet loosely with the bolts.
Make sure the gasket on the door is flush
against the cabinet and is not folded. Support
the door on the handle side and make sure the
door is straight and the gap between the doors
is even across the front. While holding the door
in place, tighten the top hinge bolts. Replace
the hinge cover.
10
C
Installation Instructions
REHANG FREEZER DOOR (For mo els
with freezer oor)
Lower the freezer door onto the bottom hinge pin.
Ensure that the plastic hinge pin thimble is on the
hinge pin or inside the door hinge pin hole located
in the bottom of the door.
Straighten the door and line it up with the
center hinge bracket.
Install the center hinge pin with a 3/4″socket
ratchet/driver. Turn it until it extends through
the hinge bracket and into the freezer door.
9
A
B
C
REHANG REFRIGERATOR DOOR
Lower the refrigerator door onto the center
hinge pin. Ensure that the plastic hinge pin
thimble is on the center hinge pin or inside
door hinge pin hole located in the bottom
of the door.
10
A
INSTALL THE LOGO BADGE
Remove the adhesive backing paper and align
the pins on the back of the badge with the
holes in the door. Apply pressure to the badge
to ensure it sticks to the door.
11
B
4
TRANSFER REFRIGERATOR
DOOR HANDLE TO RIGHT
Refer to Remove the Fresh Food Door andle
and Attach the Fresh Food Door andle
sections for instructions.
8