GE GSH25JSRISS and Operating instructions

ge.com
°e,,,_
Safety Information
Electricity ..................... 4
Extension Cords ............... 3
Proper Disposal ................. 3
Safety Precautions .............. 2
Operating Instructions
Automatic Icemaker . ........... 9
Controls ..................... 5
Crispers and Pans ............ 8, 9
Ice and _4ater Dispenser ........ 10
Shelves, Bins and Racks ........ 6-8
V\ater Filter Cartridge ........... 6
Care and Cleaning
Cleaning ................. l l, 12
I Jgh t Bulbs .................. 1,3
Installation Instruc_tions
Preparing to Install
the Refiigera/or . ........... 14, 15
*¢\ater Line Installation ...... 16-20
Troubleshooting Tips
Befbre You (:all For Service . . .22-24
Normal Operating Sounds ...... 21
Consumer Support
Consumer Support ..... Back Cover
Performance Data Sheet ........ 27
Product Registration
(Canadian) ............... 31,32
Product Registration (U.S.) . . .29, 30
State of California _\ater
Treatment Device Certificate ..... 28
_\arranty (Canadian) ........... 25
*4,wranty (U.S.) ............... 26
Models20,22and25
C&te _'_c&te
Rdfrigdrateurs
La section fran_aise commence a la page 33
Iado a lado
Refrigeradores
La seccion en espa#ol empieza en la pagina 61
Write your model and serial numbers here:
Model #
Serial #
Find these numbers on a label inside
the refrigerator compartment at the top
on the fight side behind the controls,
197D3351PO09 49-60416 11-05JR

IMPORTANTSAFETYINFORMATION.
READALLINSTRUCTIONSBEFOREUSING.
WARNING!
Use this appliance only for its intended purpose as described in this Owner's Manual
SAFETYPRECAUTIONS
When using electrical appliances, basic safety precautions should be followed, including the following:
i)::This refi'igerator must be properly installed
and located in accordance with tile Installation
Instructions before it is used.
i)::Do not allow children to climb, st;rod or hang
on the shelves in the reli-igerato_: They could
damage the reti_igerator and seriously iqj ure
themselves.
::_ Do not touch tile cold sui_lilces in tile fl'eezer
compartment when hands are damp or wet. Skin
may stick to these extremely cold sudhces,
}_'<Do not store or use gasoline or other flammable
\_q)o_ and liquids in tile vicinity of this or any
other appliance.
i)_:In refl'igerato_ with automatic icemake_,
avoid contact with the moving parts of the
ejector mechanism, or with tile heating element
located on tile bottom of tile icemake_: Do not
place finge_ or hands on tile automatic
icemaking mechanism while tile refl]gerator
is i)lugged in.
i)_:Kee I) finget_ out (ff tile "pinch point" areas;
clearances between the doo_ and between
the doo_ and cabinet are necessarily small.
Be caretul closing doo_ when children are
in the area.
i)_:Uni)lug tile refrigerator befiwe cleaning and
making repairs.
NOTE."We strongiyrecommendthatanyservicingbe
performedby aquaiified indiwdual.
_'_Setting tile fi'eezer control to tile 0(off) position
does not remove power to the light circuit.
i)_:Do not refl'eeze fl'ozen toods which have
thawed completely:

ge.com
DANGER!RISKOFCHILDENTRAPMENT
PROPERDISPOSALOFTHEREFRIGERATOR
Child entrapment and suffocation are not i)rol)lems
of the past, Junked or abandoned refl_Jgeratm_ are
still dangerous,, ,even if' they will sit fin" 'ijust a few
da_s." If you are getting rid of yore" old refl_igerato_;
please follow tile instructions below to hel I) prevent
accidents,
Before YouThrowAway YourOldRefrigerator
or Freezer:
iJi::Take off tile dome.
!i?:I,eaxe tile shelxes in place so that children ma)
not easiE climb inside.
Refrigerants
_M1refl_Jgeration products contain refl'igerants,
which under federal law InUSt be relnoved prior
to product disposal. If wm are getting rid of an
old refl_igeration product, check with the
company handling tile disposal about what
to do,
USEOFEXTENSIONCORDS
Because of potential safety hazards under certain conditions, we strongly recommend
against the use of an extension cord.
Howe\'et; if you must use an extension cord, it is absolutely necessary that it be a UL-listed (in tile United
States) or a CSA-listed (in Canada), 3-wire gro/mding _'l)e appliance extension cord having a gro/mding
_'l)e plug and outlet and that the electrical rating ot the cord be 15 amperes (minim urn) and 120 volts.
3

IMPORTANTSAFETYINFORMATION.
READALLINSTRUCTIONSBEFOREUSING.
WARNING!
HOWTOCONNECTELECTRICITY
Do not, under any circumstances, cut or remove the third (ground) prong from the power cord. For
personal safe_ this appfiance must be properly grounded.
The power cord of this appliance is equipped with
a 3-prong (grounding) plug which mates with a
standard 3-prong (grounding) wall outlet to
minimize the possibili F of electric shock hazard
fl'om this appliance.
Have the wall outlet and circuit checked by a
qualified electridan to make sure the outlet is
propedy grounded.
If the outlet is a standard 2-prong outlet, it is _mr
personal responsibili F and obligation to have it
replaced with a propedy grounded %prong wall
outlet.
The refl_igerator, should ahvavs, beI)lugged,, into its
own indixidual electrical outlet which has a xoltage
rating that matches the rating plate.
This provides the best perlimnance and also
I)rexents oxerloading, house wiring circuits which
could cause a fire hazard from oxerheated wires.
Never unplug )'our refl_igerator by pulling on the
power cord. Mways grip plug firefly and pull
straight out fl'oln the outlet.
Repair or replace immediately all power cords that
have become ti'ayed or otherwise damaged. Do not
use a cord that shows cracks or abrasion damage
along its length or at either end.
\4]_en moving the refi_igerator away from the
wall, be careflfl not to roll over or damage the
power cord.
READANDFOLLOWTHISSAFETYINFORMATIONCAREFULLY.
SAVETHESEINSTRUCTIONS
4

Aboutthe controlsontherefrigerator, ge.com
Yourcontrols will look like one of the following:
FREEZER REFRIGERATOR
OIS OFF
91SCOLDEST
I
I
/nitially, set the refrigerator compartment control at 5and the freezer
control at 5 and allow 12hours for the temperature to stabilize.
Several adjustments may be required. Adjust the controls one
increment at a time, and allow 12hours after each adjustment for the
refrigerator to reach the temperature you set.
Setting the freezer control to 0stops cooling in both the refrigerator
and freezer compartments but does not shut off electrical power to
the refrigerator.
Controlsettings will vary based onpersonal preferences, usage and
operating conditions and may require more than one adjustment.

Aboutthe water filter cartridge.(onsome models)
WaterFilterCartridge
The water filter cartridge is located in the back upper fight corner
of tile refiigerator compartrrlent.
WhentoReplacetheFilteronModelsWitha
ReplacementIndicatorLight
There is a replacement in(ficator light ior the water filter cartridge
on tile dispenser. Tills light will tm'n orange to tell }ou that _ou
need to replace the filter soon.
The filter cartridge should be replaced when the rei)lacement
indicator light turns red or if"the flow of water to tile dispenser or
icemaker decreases.
When toReplace theFilter onModels Withouta
ReplacementIndicatorLight
The filter c_mrldge sllould be replaced e_ery sixmonthsor earlier
if the tlo_ of water to the water dispenser or icemaker decreases.
RemovingtheFilterCartridge
If you _Jx_replacing the cartridge, ib_t remove the old one b_
sloMy turning it to the left. Donotpull down on file cartridge.
A small amotmt of water ma) drip down.
Installing theRlter Cartridge
O There is an adapter attached to tile top of the new filter
cartridge
+ed,e++ere.+++er+e,e+d.++d.e
To remo_e tile adal)te_;
turn it to the left about
1/4 turn. With adapter Without adapter
If_ou are re)lacing _JWater (appearance may vary)
•I ,
byCulligancartridge, leaxe the adapter in place. T]lis adapter
_qll stm in the refiJgemtor when you replace flltllre cartridges.
On models _dthout a replacement indicator light, appl? the
month and _,ear sticker to the new cartridge to remind _ou to
replace the tilter in six months.
Fill the replacement cartrktge _qth water fi'om the tap to
alh)w for better flow fl'om the dispenser immediatel} after
installation.
OIJne up the arrow on the cartridge and tile cartridge holdex:
Place the top of the new cartridge up inside the hokler. O0/10t
push it up into the holdex:
O Slowly turn it to tile fight until
the filter cartridge stops. OONOT
OVERTIGHTEN.A_you turn the
cartridge, it will mitomaticalh.
raise itself into position. The
cartridge _qll moxe about
1/2 turn.
Holder
O Rtm water fl'om tile dispenser tar 3 mim_tes (about 1-1/2
gmllons) to clear the s_stem and prexem sputtering.
OPress and hokl the RESEr @
WATERFILTERpad (on sortie
models) on the dispenser fi)r :
++ .................+++++++:+;
NOTE:A newkqnstalled water
filter cartridge m+ cause RESETWATER FILTER
water tospnrtfl'om the HOLD3SECS
dispenser.
FilterBypassPlug
31)tl must use the filter b?pass plug \d/en a replacement filter
cartridge is not mailable+ The dispenser and the icemaker will not
operam without tile filter or filmr bit)ass phtg.
SmartWater
Filter _
Bypass ,,i
Waterby Cu!ligan
To use the filter bypass plttg on Water byCulliganmodels, you must
first remme the filter adapter fl'om the cartridge holder b} turning
it to the left.
If you hme quesfions--_isit our _bsite at ge.com,
or'call 1.800.GE.(2_RES (1.800.432.2737)+
Replacementfilters:
Toorderadditionalfilter cartridgesin theUnitedStates,visit our
Websiteat ge.com,or call GEPartsandAccessories,800.626.2002.
M_\Y
Suggested Retail $38.95M7.95
()lstomers in C_ma(la should consult the }ello_+pages ti)r the
nearest (;amco Serqce Cenmr.
Customers outside of tile [lnited States or Canada should contact
the local (tistxibtttor.
Abouttheshelvesandbins.
Not all features are on all models.
! iiiii ii!II
6
Bins on the Refrigerator Compartment Door ,
A(!iusmble bins can easily be carried fi'om Thesnuggerhelps pre_ent tipping, spilling
i'e[ijoei'ator to work _lI'e_l. ( " •" " " • "
., )_shdmo of small items st(wed on the d(>i>r
Toremove: lift the fl'ont of the bin up, then _._
pull (mt. ,,.2: ,
_:111(1Iortt/ to tit _ ()fir nee(is.
Toreplace or relocate: Engage the bin in the
molded supports of the doo_; and push in.
Bin will lock in place.

ge.com
Rearranging the Shelves
Refrigerator Shelves:
ToRemove
FreezerShelves:
ToRemove
\
ToReplace
OLowor,o_rS
FreezerPan:
To Remove
Remove the pan b) pulling it fin'ward,
lifting up the fl'ont and sliding it past the
stop location.
Slide-Out Spillproof Sheff (onsomemodels)
The slide-out spillproof shelf allo_:s you to
reach items stored behind othex5. The
special edges are designed to help prevent
spills fi'om dripping to lower shelves.
Makesureyoupushtheshelvesall the wayback
in beforeyouclosethedoo_
ISpillproof Shelves (onsomemodels)
Spillproof shelves have sI_ecial edges,
to hel I) prevent spills fl'om drili ) )im,,_ to
lower shelx es.
Quick Space Shelf (onsomemodels)
This sheff splits in half and slides trader
itself for storage of trill items on the shelf
below.
ii iljl _ Deep Door Shelves
Detachable shelf extende_s deepen and
enclose fixed door shelves, providing
IllOI'e stoi_lge i'ooi/l and greater storage
flexil)ilim
Toremove: I,ifl the shelf extender straight
up then pull out.
Toreplace: Engage the sheff extender in the
molded suI_ports on the door and push in.
It will lock in place. 7

Abouttheadditional features.
Not all features are on all models.
ShelfSaver TM Rack
(onsomemodels)
Use this rack to store
beverage C_lIIS J[OI" eas\'
access.
It can also heM a 9" x 13"
baking dish.
Door Can Rack
(on some models)
This door rack holds up
tO 9 (arts.
NOTE."Thisrackcanonlybe
mounted/)_thetopposition
underthedairyb#7.
z_
iiTM
Aboutthe crispersandpans.
Not all features are on all models.
Fru# and Vegetable Crispers
Excess water that mm accumulate in the
bottom of the (h'awe_s should be wiped (h_.
I JJ I¢ illl illl II II I Adjustable Humidity Crispers and Snack Pan (onsomemodels)
Slide the control all the way to the Slide the control all the wm to the L0w
Highsetting to provide high h umiditx ,settim,_ to proxide lower h umidit} lexels
recommended tot most xegetables, recommended tot most fl'uits.
N0rrnal
Coldest
Convertible Meat Pan (onsomemodels)
The convertible meat pan has its own cold
air duct to allow a stream of cold air fl'om
the ti'eezer COIIlp[lI'tlIlent 10 1low [lI'Otln(1
the pan.
Thevariabletemperaturecontrolregulates
the air rio\\' from the fl'eezer compartment.
Set control lever up to convert the pan
to nomml refligerator temperatm'e and
provide extra vegetable storage space. (]old
air duct is turned ofl_ V;uiable settings
between these extremes can be selected,
Set control lever down to the coldest setting
to store ti'esh meats. If lever is lett in meat
position tot a hmg period of time, solne
fl'ost may titan on the inside ot the pan.

Aboutcrisperremoval gecom
Not all features are on all models.
Crisper
Guides
When replacing flTecrispers, make
sure you slide them through the
crisper guides.
Crisper Removal
(:risl)e_ can easilx be removed bx, tiltino_ uo
slightly and pulling past stop location. If tile door prevents you fl'om taking out the crispers, the refl_igerator will need to
be rolled forward until tile door opens
enough to slide tile crispe_ out. In some
cases, when you roll the reti_igerator out,
wm will need to move the reti_igerator to
the left as w)u roll it out.
Abouttheautomaticicemaker.
A newly-installed refrigerator may take 12-24 hours to begin making ice.
Power Atltomatic lcemaker (onsome models)
Switch Icernaker Tile icemaker will produce seven cubes
per cycle'--aI)I)roMmately 100-130 cubes
in a 24-hour period, depending on fl'eezer
COllll)ai'tl/lent tellll)ei'iltui'e _ i'ooi11
temperattire, nUlllbei" of door ol)enings
} and other tlse conditions.
Greet If tile reflJgerator is operated befiwe tile
PowerLight erArm water connection is made to tile icemake_;
set the power switch in the 0 (off) position.
X&hen the reti_igerator has been connected
to tile water sui)plv set tile power switch to
tile I (on)position.
Tile icemaker will fill with water when it
*-0 .... r
c()()ls t() l:) F. A newly-installed refngerat()r
ma) take 19 to 24 ho/u_ to begin making
ice cubes.
You will hear a btlzzin r SOtlnd each time
the icemaker fills with water:
Throw awm the first tew batches of ice to
allow the water line to clea_:
Be sure nothing interteres with the sweep
of tile feeler am_.
When tile bin fills to tile level (ff tile ti_eler
am_, tile icemaker will stop producing ice.
It is nolinal for several cubes to be joined
together:
If ice is not used fl'equenfl> old ice cubes
will become cloudy, taste stale and shrink.
NOTE."Inhomes with lower-than-averagewater
pressure,youmayhear the i?emakercycle mu/tl_)/e
tlYneswhenmakingone batchof ice.
Freezer
There is an upper freezer shelf
above the icemaker that can be
used for storage.
iiii
...........
'_ii! iIII
Ice Storage Drawer
Toaccess ice, pull tile drawer out. Toremove the drawer, pull it straight out
and lift it past tile stop location.
Icemaker Accessory Kit
If your refrigerator did not come ah'ea(l_
equil)ped with an automatic icemake_;
an icemaker accessor_ kit is ax filable at
extra cost.
Check tile back of tile refligerator fiw
the specific icemaker kit needed fi)r
_()tlI" model.

Aboutthe ice and water dispenser.
On some models
r
SpillShelf
To Use the Dispenser
Select CUBEDICE _, CRUSHEDICE
or WATER_.
Press tile glass gently against tile top ot
tile dispenser cradle.
The spill shelf is not selCdraining. To
reduce water spotting, the shelf and its
grille should be cleaned regularl>
If no water is dispensed when the refrigerator
is first installed, there may be air in the water
line system. Press the dispenser arm for at least
two minutes to removetrapped air from the water
line and to fill the water system. Toflush out
impurities in the water line, throw away the first
sixglassfub of water
CAUTION: Neverput fingers or any other
objects into the ice crusher discharge opening.
Lockingthe Dispenser(onsomemodels)
Press the LOCK
CONTROLpad fi,r
3 seconds to lock tile
dispenser and control
LOCKCONTROL panel. To mflock, press
HOLD3SECS and hold tile pad again
fi)r 3 seconds.
Dispenser Light
This pad turns tile
dispenser on and off.
The light also comes
LIGHT on when tile disl)enser
cradle is pressed. If this
light bm'ns out, it
should be replaced
xdth a 6 watt ma_mum,
12 xolt DC bulb.
10
Ice Storage Drawer
on Dispenser Models
Toremove:
Set tile icemaker power switch to tile
0 (off)position. Pull tile drawer straight
Otlt and then lilt past tile stop position.
Toreplace:
\_l/en replacing tile (h'awe_; make sure
to push it firefly into place. If it does not
go all the way back, remove it and rotate
tile drive mechanism 1/4 turn. Then push
the drawer back again.
Important Facts About Your Dispenser
iJi::Do not ::1(1(1ice ti'om trm:s or bags to
the storage bin. It may not crush or
dispense well.
iJi::Avoid ove_tilling glass with ice and use ()I
narrow glasses. Backed-up ice can jam tile
chute or catlse tile door in tile chute to
ti'eeze shut. If ice is blocking the chute,
poke it through with a wooden spoon.
iJi::Beverages and fi)ods should not be
quick-chilled in the ice storage bin.
Cans, bottles or fi)od packages in tile
storage bin may cause tile icemaker
or auger to jam.
iJi::To kee I) dispensed ice fl'om missing
the glass, put the glass close to, but not
touching, the dispenser opening.
iJi::Some crushed ice may be dispensed even
though you selected CUBEDICE.This
hapl)ens occasionally when a low cubes
have been left in tile crusher.
iJi::_Mter crushed ice is dispensed, some
water may drip fl'om tile chute.
iJi::Sometimes a small mo/md (ffsnow will
t0m_ on tile door in tile ice chum. This
condition is nomml and usually occm_
when w)u have dispensed crushed ice
repeatedly. Tile snow will eventually
evaporate.
_: Tile fi_t glass ot water dispensed may be
w;mner than the tollowing ones. This is
noii/lal.
_: Dispensed water is not ice cold. For
colder water; simply add crushed ice or
cubes befi)re dispensing water:

Careand cleaningoftherefrigerator, gecem
Dispenser drip area.
Cleaning the Outside
The dispenser drip area, (on soine models)
beneath the grille, shotfld be wii_d di T._,V_ter
left in this area nlay leave deposits. Remove
the deposits b)' adding undihlted vinegar to
the well. Soak until the deposits disappear
0I" becoille loose enotlgh to IJnse awav.
The dispenser cradle (oil seine nlodels).
gefoi'e cleaning, lock the dispenser by
pressing and holding the LOCK CONTROL
pad fi)r 3 seconds. Clean with waml water
and baking soda sohlfion--about a
tablespoon (l 5 inl) of baking soda to a
quart (l 1) ot watei; Rinse thoroughly
and wipe dry:
The door handles and trim. Clean with a
cloth danlpened with soap) wateI: DI'_
with a soft cl()th.
Keep the outside clean. Wipe with a clean
cloth lightly danq)ened with kitchen
appliance wax or mild liquid dish deteIgent.
DIT and polish with a clean, soft cloth.
Do not wipe the torrid?oratorwith a soi/ed dish
cloth or wet towel Thesemay leave aresidue
that can erode the paint. Do not use scouring
pads,powdered c/eanere, bleach or cleaners
containing bleach because these products can
scratch and weaken the paint finish.
Cleaning the Inside
Tohelp prevent odors,lea',e an open box ot
baking soda in the refrigerator and fl'eezer
COIl/pa I'tlll eats.
Unplug the refrigerator before cleaning. If this
is not practical, wring excess n/oisture ()tit
of sponge or cloth when cleaning around
switches, lights or controls,
Use warn/water and baking soda sohltion--
about a tablespoon (l 5 inl) el bakhlg soda
to a quart (l 1) oI wateI: This both cleans
and neutralizes odoI_. Rinse and wipe dry.
_MteI"cleaning the door gaskets, apply a
thin laver of petroleunljelly to the door
gaskets at the hinge side. This helps kee I)
the gaskets fl'oin sticking and bending ()tit
of shape.
Drain opening in freezer compartment.
During yearly cleaning, renlove botton/
fl'eezer pan and fltlsh a sohltion of baking
soda--1 teaspoon (5 inl) and 2 cups (500
n/l) (ff hot (not boiling) watei_through
the drain line with the help of a nleat
bastei: This will help elinlinate odor and
reduce the likelihood (ff a clogged drain
line./t drain becon/es clogged, use a nleat
baster and baking soda sohltion to t0rce the
clog through the drain line.
Avoid cleaning cold glass shelves with hot water
because the extreme temperature difference may
cause them to break. Handle glass shelves
carefull_z Bumping tempered g/ass can cause it
to shatter
Donot washanyplasticrefrigeratorpartsin the
dishwasher
Condenser
There is n() Ileed ik)l" i'otltille condensel"
cleaning in natural hence q)el'afing
environlllelltS. Howe\vi; in etlviro/lI//ents
that may be patlicularly dusty or greasy, the
condenser shonkl be cleaned periodically
fi)r eflident reflJgemtor operation,
Cleaning the condenser:
The condenser is located inside the back
(>fthe reflJgeratoI: To access it, fiI_t unplug
the reti_igeI'atOl: Then renlove the access
level: The condenser is on the right side.
11

Careand cleaningofthe refrigerator.
Behind the Refrigerator
Be caI'eflll when moving the refl_igerator
away fl'oln the wall. _dl types of floor
coverings can be dalnaged, particularly
cushioned coverings and those with
elllbossed S/lI]_lces.
Pull the reflJgerator straight out and returi_
it m position by pushing it straight in.
Moving the x'efl_igex'ator in a side dixection
Inay result in damage to the floor cox'ering
or refl_igeratoi:
When pushing the refrigerator back, make sure
you don't rofl over the power cord or icemaker
supply line (onsome models).
Preparing for Vacation
For long \;l(ations or absen(es_ i'elllOVe
food and tmplug the refl_igeratoi: Clean the
interior with a baking soda sohKion _ff one
tablespoon (15 ml) of baking soda to one
quart (l 1) of watei: i,eave the dooi_ open.
Set the icelnaker power switch to the 0(off)
position and shut off the water supply to
the i'efl_igelatoi:
If the telnperamre can drop below
fi'eezing, have a qualified servicer drain the
water supply systein (on some Inodels) to
prevent serious propei_y dalnage due to
flooding.
Preparing to Move
Secure all loose itelns such as grille, shelves and di'awei5 by taping theln securely
in place to prevelK dalnage.
Be sure the refrigerator stays in an upright position during moving.
12

Replacingthelightbulbs, gecom
Turning the control to the 0(off) position does not remove power to the light circuit.
Refrigerator Compartment--Upper Light
0 Unplug the relrigerator. Phm the0 _ refl_igerator back in.
@The bulb is located behind the controls.
O"
Replace with an appliance bulb f the
saI/le oi" lower wattage.
Refrigerator Compartment--Lower Light fonsomemodels)
This i/ght is iocated above the top drawe_ _ After replacing with an appliance
bulb of the same or lower wattage,
0 Unplug the refrigerator: replace the shield.
@(;rasp the lip at the bottom of the light _ Plug the refrigerator back in.
shield and pull it up and fiwward.
Freezer Compartment
Un )lug the rehigerator
@ Remoxe the shelf just below the light
shield. (The shelf will be easier to
remoxe if it is emptied fixst.)
Lift up on the light shield to remoxe.
OAfter replacing with an appliance
bulb of the same or lower wattage,
reinstall the shield b) hanging it
from the three tabs.
Reinstall the shelf and )lu,* the
refrigerator back in.
Dispenser
Un )lug the rehigerator
_The bulb is located on the dispenser
under the control panel.
Remoxe the light bulb b) tm'ning
it cotmterclockwise.
Replace the bulb with a bulb of the
same size and wattage.
Plug the refrigerator back in.
13

Installation
Instructions Refrigerator
Models 20,22,25
Questions?Call800.GE.CARES(800.432.2737)or visitore" X_ebsite at: ge.com
In Canada,call 1.800.361.3400or visitomX_Vbsite,t: www.geappliances.ca
BEFORE YOU BEGIN
Read these instructions completely and carefully.
•IMPORTANT -hese
instructions for local inspector's use.
"IMPORTANT -()bserveaH
_o_ erllillo codes ;Hid ordillall(es.
• Note to Installer -Be sm'e to leave these
instructions with tile Consumer.
• Note to Consumer - Kee I) these instructions
foF [(Ittlre reference.
• Skill level - hlstallation of this appliance requires
basic mechanical skills.
• Completion time - Refrigerator Installation
l 5 minutes
" Proper installation is tile responsibilit} of tile
installer.
• Product fhilure due to improper installation is not
co'_ered under tile _arranty.
WATER SUPPLY TO THE ICEMAKER
(on some models)
If tile reli'igerator has an icemakei; it will have to
be connected to a cold water line. AGE water supply
kit (containing tubing, shutoff wdve, fittings and
instructions) is awfilable at extra cost from yore" dealei;
by visiting ore" X,Vebsite at ge.com (in Canada, at
www.geappllances.ca) or from Parts and Accessories,
800.626.2002.
REFRIGERATOR LOCATION
•Do not install tile refl'igerator where tile temperatm'e
will go beh)w 60°F (l 6°C) because it will not itm often
enough to maintain proper temperatures.
•Install it on a floor strong enough to suppoI_t it filly
loaded.
CLEARANCES
_Mlow tile following clearances tor ease of installation,
proper air drculation and phmfl)ing and electrical
colnxectiolxs.
• Sides 1/8" (4 ram)
• Top 1" (25 ram)
•Back 1" (25 ram)
A door clearance ot 3/4" (l 9 Iron) is needed fin" a 90 °
door opelfing which provides better access to tile ti)od
storage aYea.
ROLLERS
The rollers have 3 purposes:
• RolleI_ a(!just so tile door closes easily when opened
about hallway.
• RolleI_ at!just so tile refl_igerator is firefly positioned
on tile floor and does not wobble.
• Rollei_ alh)w you to m ore the reti-igerator away fl'om
the wall fin" cleaning.
To adjust the milers, remove tile base grille b) pulling it
out at tile bottom.
'_ .]] ..... .
Turn tile roller ac!jusfing screws clockwise to raise tile
I eh]oeI
• "_ "at(n; comlterdockwise to lower it. [.lse an
a(!justable wrench (./8 hex head bolt) or pliei_.
To replace base grille, line up tile clips on back of grille
between the bar and the bottom of the cabinet. Push
fi)rward tmtil _(*rillesnaps into place.
I
14

Installation Instructions
DOOR ALIGNMENT
_Mter leveling, make sure that doo_3 are even at tile top.
To make the doors even, a(!just tile reflJgerator dooi;
0 Using a 5f] 6" socket wI'ench, ttlI'II tile door a(!jHsting
screw to tile right to raise tile doo_; to tile left to lower
it. (A nylon plug, embedded in tile threads of tile pin,
prevents tile pin fl'om turning mfless a wrench is
used.)
@ _Mter one or two turns of tile wrench, open and close
tile refl_igerator compartment door and check tile
aligmnent at the top of the dome,
5/16"Socket
Wrench
Toremovetbebase
grille,openthedoors
andthenpullthe
grillestraightout.
15

Installation instructions
iNSTALLiNG THE WATER LiNE
BEFORE YOU BEGIN
P.econ/mended copper water supply kits are WXSX2,
WX8X3 or WX8X4, depending on the amount of
tubing you need. Approved plastic water supply lines
are GE SmartConnect'" Refl'igerator Tubing
(WX08X10002, WX08X10006, WX08X10015 and
WX08X10025).
When connecting yore" refl'igerator to a GE Reverse
()smosis _'_ater S}_stem, the only approved installation
is with a GE RVKit. For other revelse osmosis water
systems, follow the mansffhctm'er's recmmnendations.
If the water sui)i)ly to the iefl'igerator is ti'om a P,everse
()smosis _'LJter Filtration System AND the reii'igerator
also has a water filtei, use the refl'igerator's filter bypass
plug. Llsing the refl'igerator's water filtration cartridge
ill col_jsmction with the RO filter can result in hollow
ice cubes and slower water flow fl'om the water
dispenser.
This water lisle installation is not warranted by the
refl'igerator or icemaker mansffhcturer. Follow these
instructions carefully to minimize the risk of expensive
water damage.
_'Laer lmmmer (water banging in the pipes) ill house
plmnbing can cause damage to refl'igerator parts and
lead to water leakage or flooding. (;all a qualified
plmnber to correct water lmmmer beflwe installing
the water supply lisle to the refi'igerator.
To prevent burns and product damage, do slot hook
up the water line to the hot water lisle.
If you use votlr refl'igerator bet/re connecting the
water line, make sure the icemaker power switch is in
the 0(off) position.
Do not install tile icemaker robing in areas where
temperatures fhll below fl'eezing.
When using ally electrical device (such as a power
drill) dm'ing installation, be sure the device is double
insulated or grotmded in a maxmer to pievent the
hazard of electric shock, or is battery powered.
All installations must be in accordance with local
phm/bing code requirements.
WARNING - Connect to potable
water supply only.
WHAT YOU WILL NEED
//
• Copper or GE SmartConnect" Refrigerator Tubing
kit, l/4" outer dialneter to connect the reli'igerator
to the water supply, If using copper, be sure both ends
of the tubing are cut square.
To deteiinine how inuch tubing you need: nleasure
tile distance ti'oln the water valve on the back of the
reli'igerator to the water supply pipe. Then add 8'
(2.4 I/l). Be sure there is sufficient extra tubing (about
8' [2.4 Ill] coiled into 3 turns of about 10" [25 cm]
diameter) to allow the reli'igerator to move otlt ti'oIll
the wall atier installation.
GE SnmrtConnect'" Refl'igerator Tubing lZdts are
awfilable in the fi_llowing lengths:
2' (0.6 Ill) -- _4_X08X10002
6' (1.8 Ill) -- WX08X10006
15' (4.6 Ill) -- WX08X10015
25' (7.6 I/l) -- WX08X10025
Be sure that the kit vou select allows at least 8' (2.4 I/l)
as described above.
NOTE: The only GE approved plastic tubing is that
supplied in GE SmartCmmect'" Refrigerator Tubing
kits. Do not use any other plastic water supply line
because the line is under pressure at all times. Certain
types of plastic will crack or rupture with age mid cause
water damage to your home.
16

Installation instructions
WHAT YOU WILL NEED (CONT.)
• A GE water supply kit (containing tubing, shutoff
wflve and fittings listed below) is awfilable at extra
cost flxm_ vour dealer or fl'om Parts and Accessories,
800.626.2009.
•A cold water supply. The water pressure must be
between 20 and 190 p.s.i. (1.4-8.2 bar) on models
without a water filter and between 40 and 190 p.s.i.
(2.8-8.2 bar) on models with a water filter.
•Power drill.
• 1/2" or adjustable wrench.
• Straight mad Phillips blade screwdriver.
• Two 1/4" outer diameter compression nuts and
2 ferrules (sleeves)--to connect the COl)per tubing
to the shutoff valve and the refrigerator
water walve.
OR
• If wm are using a GE Slnart(_olmect _'_Refl'igerator
Tubing kit, the necessa_ y fittings are preassembled to
the tubing.
• If wmr existing COl)per water line has a flared fitting
at the end, you will need an adapter (available at
plumbing supply stores) to connect the water line to
the refl'igerator OR you can cut off the flared fitting
with a tube cutter and then use a compression fitting.
Do not cut formed end from GE SnlartConnect'"
Refl'igerator tubing.
•Shutoff valve to connect to the cold water line.
The shutoff wflve should have a water inlet with a
minimum inside diameter of 5/32" at the point of
connection to the COLD WATER LINE. Saddle-type
shutoffvalves are included in many water supply kits.
Betore imrchasing, make sure a saddle-type valve
complies with vom" local plumbing codes.
Install the shutoff valve on the nearest frequently used
drinking water line.
[] SHUT OFF THE MAiN WATER
SUPPLY
Turn on the nearest taucet long enouoh_ to clear
the line of water.
[] CHOOSE THE VALVE LOCATION
Choose a location fl_r the valve that is easily
accessible. It is best to connect into the side of a
vertical water pipe. When it is necessary to connect
into a horizontal water pipe, make the connection
to the top or side, rather than at the bottom,
to awfid drawing off anv sediment from the
water pipe.
[] DRILL THE HOLE FOR THE VALVE
Drill a 1/4" hole in the water pipe (even it using a
sell:piercing wflve) using a sharp bit. Remove any
burI_ resulting fl'oin drilling the hole in the pipe.
Take care not to allow water to drain into the drill,
Faihu'e to drill a 1/4" hole may result in reduced
ice production or smaller cubes.
17

Installation Instructions
INSTALLING THE WATER LINE (cont.)
[] FASTEN THE SHUTOFF VALVE
Fasten the shutoff _al_e to the cold water pipe with
the pipe clamp.
PipeClamp --_
Saddle-Type J -VerticalCold
ShutoffValve WaterPipe
NOTE: Commonwealth of Massachusetts Plmnbing
Codes 248CMR shall be adhered to. Saddle wflves
are illegal and use is not permitted in Massachusetts.
Consult with wmr licensed i)lmnber.
[] TIGHTEN THE PIPE CLAMP
Tighten tile clamp screws until tile sealing washer
begins to swell.
NOTE: Do not overtighten or you mav c_ush tile
tubing. Washer
PipeClamp__
! J
ClampScrew--
[] ROUTE THE TUBING
Route tile tubing between tile cold water line and
tile refl'igera tot.
Route tile tubing through a hole drilled in tile wall
or floor (behind tile refrigerator or a@_cent base
cabinet) as close to the wall as possible,
NOTE: Be sm'e there is sufficient extra tubing
(about 8' [2.4 m] coiled into 3 tm'ns of about 10"
[25 cm] diameter) to allow tile refl'igerator to move
out fi'om the wall after installation.
[] CONNECT THE TUBING
TO THE VALVE
Place the compression nut and teHule (sleexe) for
coI)per tubing onto tile end of tile tubing and
connect it to tile shutoff xalxe.
Make sure tile tubing is flflly inserted into tile valve.
Tighten the compression nut secm'elv.
For plastic tubing fl'om a GE Sn/art(_onnect TM
Refl'igerator Tubing kit, insert tile molded end
of the tubing into the shutoff wflve and tighten
compression nut tmtil it is hand tight, then tighten
one additional turn with a wrench. Overtightening
Ill}IV Ca/ISe leaks.
,ressi0nNut
Saddle-Type
ShutoffValve SmartC0nnect_
Tubing
PackingNut --
Outlet Valve -- -- Ferrule (sleeve}
NOTE: Commonwealth of Massachusetts Phtml)ing
Codes 248CMR shall be adhered to. Saddle wdves
are illegal and use is not permitted in Massachusetts.
Consult with yore" licensed l_lmnl)e_:
[] FLUSH OUT THE TUBING
Turn tile main water supply on and flush out tile
tubing tmtil tile water is clear.
Shut tile water off at tile water valve after about
one quart (l liter) of water has been flushed
through tile tubing.
18

Installation Instructions
[] CONNECT THE TUBING TO THE
REFRIGERATOR
NOTES:
•geti)re making tile connection to tile reti'igerator,
be sure tile refl'igerator power cord is not
I)lugged into tile wall outlet,
•If your refl'igerator does not have a water filte_,
we reconlnlend installing one if w)ur water sui)ply
has sand or particles that could clog tile screen of
tile refl'igerator's water valve. Install it in tile
water line near tile refl'igerator. If using a GE
SmartConnect '_ I).efrigerator Tubing kit, you
will need an additional tube (WXOSX10009)
to connect tile filter. Do not cut plastic tube
to install filter.
Some models have tile refl'igerator connection at
tile end of tubing located outside tile compressor
compartment access cover. On other models, tile
COIlll)I'eSSOI" COIIll)_lI'tIIlent access cover II/tlS[ be
removed in order to access the refrigerator
connection at tile watei" wllve.
On models using tile refrigeration connection at
tile water xalxe, remoxe tile plastic flexible cap.
©
Place tile compression nut and ferr/fle (sleeve)
onto the end of the tubing as shown. On a GE
Smarteonnect Refl'igerator Tubing kit, tile nuts
are ah'eadv assembled to tile tubing.
[] CONNECT THE TUBING TO THE
REFRIGERATOR (CONT.)
Insert tile end of tile tubing into tile reli'igerator
connection as far as possible. While holding tile
tubing, tighten tile fitting.
For plastic tubing fl'om a GE SmartConnect
Refl'igerator Tubing kit, insert the molded end of
tile tubing into tile refl'igerator connection and
tighten the compression nut until it is hand tight,
then tighten one additional turn with a wrench.
Overtightening may cause leaks.
Fasten the tubing into the clamp provided as
shown to kee I) it in position. You may need to pry
open tile clamp.
One of the illustrations bdow will look like the
com_ection on your refrigerator.
1/4"
Tubing
Clamp Tubing
Nut
Ferrule
(sleeve)
Refrk
Connection
cTU'°b2
Ferrule _ _222__
{sleeve)_
Refrigerator/_'_ _l_i_
Connection
SmartConnect_
Tubing
1/4" 1/4"
Tubing
SmartConnect_
Tubing
[] TURN THE WATER ON AT THE
SHUTOFF VALVE
Tighten any connections that leak.
Reattach tile access cover.
19

Installation Instructions
INSTALLING THE WATER LINE (cont.)
[] PLUG IN THE REFRIGERATOR
__rranoe the coil of tubing so that it does not xibrate
against the back of the refrigerator or against the
wall. Push the refrigerator back to the wall.
START THE ICEMAKER
Set the icemaker power switch to the I (on)position.
The icemaker will not begin to operate until it
reaches its operating temperature of 15°F (-9°C)
or below. It will then begin operation automaticallv
if the icemaker power switch is in the I (oil)position.
NOTE: In lower water pressure conditions, the
water xalxe may turn on up to 3 times to delixer
enotwh water to the icemake_:
2O