GE 21008 User manual

1
We bring good things to life.
2.4 GHz Dual Cordless Handset
Call Waiting Caller ID Phone System
User’s Guide
21008

2
IMPORTANT INFORMATION
NOTICE:This product meets the applicable Industry Canada technical specifications.
The equipment must be installed using an acceptable method of connection.The customer
should be aware that compliance with the above conditions may not prevent degradation of
service in some situations.
Repairs to certified equipment should be made by an authorized Canadian maintenance
facility designated by the supplier. Any repairs or alterations made by the user to this
equipment, or equipment malfunctions, may give the telecommunications company cause to
request the user to disconnect the equipment.
Users should ensure for their own protection that the electrical ground connections of the
power utility, telephone lines and internal metallic water pipe systems, if present, are
connected together.This precaution may be particularly important in rural areas.
CAUTION: Users should not attempt to make such connections themselves, but should
contact the appropriate electric inspection authority, or electrician, as appropriate.
NOTES: This equipment may not be used on coin service provided by the telephone
company.
INTERFERENCE INFORMATION
This equipment generates and uses radio frequency energy which may interfere with
residential radio and television reception if not properly installed and used in accordance
with instructions contained in this manual. Reasonable protection against such interference
is ensured, although there is no guarantee this will not occur in a given installation. If
interference is suspected and verified by switching this equipment on and off, the user is
encouraged to try to correct the interference by one or more of the following measures:
Reorient the radio/television receiver’s antenna, relocate the equipment with respect to the
receiver, plug the equipment and receiver into separate circuit outlets.The user may also
wish to consult a qualified radio/television technician for additional suggestions.This
equipment has been fully tested and complies with all limits for Class B computing devices
pursuant to part 15 FCC Rules and Regulations.This device complies with RSS-210 of
Industry Canada. Operation is subject to the following two conditions: (1)This device may
not cause interference, and (2)This device must accept any interference, including
interference that may cause undesired operation of the device.
HEARING AID COMPATIBILITY (HAC)
This telephone system meets FCC/Industry Canada standards for Hearing Aid Compatibility.
REN NUMBER IS LOCATED ONTHE CABINET BOTTOM

3
TABLE OF CONTENTS
IMPORTANT INFORMATION ....................... 2
INTERFERENCE INFORMATION ................... 2
HEARING AID COMPATIBILITY (HAC) ........ 2
FCC RF RADIATION EXPOSURE
STATEMENT .................................. 5
INTRODUCTION ..................................... 5
HANDSET LAYOUT ................................. 7
BASE LAYOUT ...................................... 8
HANDSET CHARGE CRADLE LAYOUT ......... 8
PARTS CHECKLIST ................................. 9
TELEPHONE JACK REQUIREMENTS ........ 9
INSTALLATION ..................................... 10
INSTALLATION GUIDELINES ................ 10
INSTALLING THE PHONE ..................... 11
CONNECTING THE AC (ELECTRICAL)
POWER ........................................... 11
CONNECTING THET ELEPHONE LINE ...... 11
INSTALLING THE HANDSET BATTERY .... 12
WALL MOUNTING THE BASE ............. 12
PROGRAMMING THET ELEPHONE ............. 13
STANDBY SCREEN ........................... 13
PROGRAMMABLE FUNCTIONS ............. 13
LANGUAGE ............................. 13
HANDSET NAME ...................... 13
AREA CODE ............................ 14
RINGER T ONE .......................... 14
TONE/PULSE ........................... 14
REGISTRATION ......................... 15
DE-REGISTRATION .................... 16
GLOBAL DE-REGISTRATION ......... 16
DEFAULT SETTING .................... 17
TELEPHONE OPERATION ....................... 17
CHARGE INDICATOR ......................... 17
MAKING CALLS .............................. 17
ANSWERING CALLS ......................... 18
CALLT IMER .................................... 18
AUTO STANDBY .............................. 18
RINGER ON/OFF ............................. 18
FLASH/CALL WAITING ...................... 19
LAST NUMBER REDIAL ..................... 19
EXIT ............................................. 19
PAGE ............................................ 20
HANDSET TO HANDSET PAGING .. 20
PAGING FROM THE BASE/GROUP
PAGE ................................. 20
MUTE ........................................... 20
TEMPORARY T ONE DIALING ............... 20
RECEIVER VOLUME CONTROL ............. 21
INTERCOM OPERATION ......................... 21
MAKING AN INTERCOM CALL ..... 21
RECEIVING AN INTERCOM CALL ... 22
ADVANCED INTERCOM FEATURES ........ 22
RECEIVING AN INCOMING
TELEPHONE CALL DURING
AN INTERCOM CALL .............. 22
SEE MARKING ON BOTTOM / BACK OF PRODUCT
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING:TO
PREVENT FIRE OR
ELECTRICAL SHOCK
HAZARD, DO NOT
EXPOSETHIS
PRODUCT TO RAIN
OR MOISTURE.
THE LIGHTNING
FLASH AND ARROW
HEAD WITHIN THE
TRIANGLE IS A
WARNING SIGN
ALERTING YOU OF
“DANGEROUS
VOLTAGE” INSIDE
THE PRODUCT.
CAUTION: TO REDUCE THE
RISK OF ELECTRIC SHOCK, DO
NOT REMOVE COVER (OR
BACK). NO USER
SERVICEABLE PARTS INSIDE.
REFER SERVICING TO
QUALIFIED SERVICE
PERSONNEL.
THE EXCLAMATION
POINT WITHIN THE
TRIANGLE IS A
WARNING SIGN
ALERTING YOU OF
IMPORTANT
INSTRUCTIONS
ACCOMPANYING
THE PRODUCT.
CAUTION:

4
SAVE THESE INSTRUCTIONS
USING INTERCOM WITH
EXTERNALT ELEPHONE CALLS .22
TWO-WAY CALLING ........................ 22
THREE-WAY CALLING ...................... 23
TRANSFERRING EXTERNAL CALLS TO
OTHER HANDSETS .......................... 23
MEMORY ........................................... 23
STORING ANAME AND NUMBER IN
MEMORY ....................................... 24
STORING THE LAST NUMBER DIALED .. 24
INSERTING APAUSE IN THE DIALING
SEQUENCE (OF ASTORED NUMBER)... 25
REVIEWING RECORDS STORED
IN MEMORY ................................... 25
CHANGING RECORDS STORED
IN MEMORY ................................... 25
DELETING RECORDS STORED
IN MEMORY ................................... 25
DIALING ANUMBER FROM MEMORY ... 26
CHAIN DIALING FROM MEMORY ......... 26
CALLER ID (CID) ............................... 27
CID ERROR CODES ......................... 27
RECEIVING CID RECORDS ................. 27
STORING CID RECORDS (INCALLER ID
MEMORY) ...................................... 28
REVIEWING CID RECORDS ................ 28
STORING CID RECORDS IN INTERNAL
MEMORY ....................................... 28
DIALING ACID NUMBER .................. 29
DELETING ACID RECORD ................ 30
DELETING ALL CID RECORDS ........... 30
CHANGING THE BATTERY ...................... 31
BATTERY SAFETY PRECAUTIONS ......... 31
BELT CLIP AND OPTIONAL HEADSET ....... 32
CONNECTING THE BELT CLIP .............. 32
CONNECTING AN OPTIONAL
HEADSET TO THE HANDSET ................ 32
DISPLAY MESSAGES ............................ 33
HANDSET SOUND SIGNALS .................. 34
TROUBLESHOOTING GUIDE ................... 35
GENERAL PRODUCT CARE .................... 38
CAUSES OF POOR RECEPTION ............... 38
TELEPHONE NETWORK INFORMATION ...... 39
REN NUMBER ................................... 39
INDEX ............................................... 40
SERVICE ............................................ 42
ACCESSORY ORDER FORM ................... 43

5
FCC RF RADIATION EXPOSURE STATEMENT
This equipment complies with FCC RF radiation exposure limits set forth
for an uncontrolled environment.This equipment should be installed and
operated with a mininum distance of 20 centimeters between the radiator
and your body.This transmitter must not be co-located or operated in
conjunction with any other antenna or transmitter.
For body worn operation, this phone has been tested and meets the FCC
RF exposure guidelines when used with the belt clip supplied with this
product. Use of other accessories may not ensure compliance with FCC RF
exposure guidelines.
INTRODUCTION
CAUTION: When using telephone equipment, there are basic safety
instructions that should always be followed. Refer to the IMPORTANT
SAFETY INSTRUCTIONS provided with this product and save them for
future reference.
Congratulations on purchasing the GE Dual Cordless HandsetTelephone
System.This system operates in the 2.4 GHz frequency range, and is unique
to conventional cordless telephones. When the base is connected to electrical
power and a telephone line, you can place a fully-featured cordless handset
anywhere electrical power is available.
Features:
•2.4 GHz digital technology
•Handset to handset Intercom
•2-way and 3-way Conference/CallTransfer
•Call Waiting and Caller ID Compatible
•Tone/Pulse Dialing
•Up to 50 Name and Number Memory Dialing
This telephone has been designed to be simple to use, however, you can
reach its full potential more quickly by taking a few minutes to read this
Instruction Book.This telephone is a multifunction product for use with Call
Waiting and Caller ID services available from your local telephone company.

6
Your Caller ID Call Waiting phone allows you to:
•View the name and telephone number of a caller (Call Waiting Caller ID)
while you are on the phone.
•Identify callers before you answer the phone.
•View the time and date of each incoming call.
•Record up to 40 Caller ID messages sequentially.
•Know who called while you are on the other line or when you were away.
•Screen unwanted calls, eliminate harassment from annoying calls, or to
get prepared before answering a call.
IMPORTANT: Because cordless phones operate on electricity, you should
have at least one phone in your home that isn’t cordless, in case the power in
your home goes out.
IMPORTANT: In order to use all of the features of this telephone, you must
subscribe to two separate services available from your local telephone
company: the standard Name/Number Caller ID Service to know who is
calling when the phone rings and Call Waiting Caller ID Service to know who
is calling while you are on the phone.

7
I
N
T
9
wxyz
6
mno
3
def
8
tuv
5
jkl
2
abc
7
pqrs
4
ghi
1
0
oper
#
pause
*
tone
v
v
RINGER
PAGE
FLASH
REDIAL
talk
format
c
o
n
f
e
r
e
n
c
e
c
a
l
l
b
a
c
k
c
i
d
/
v
o
l
MUTE
program
MEM EXIT
D
E
L
E
T
E
talk/callback button
display
format/conference button
cid/vol (up or down
arrow) buttons
REDIAL button
PAGE/INT button
RINGER button
FLASH/DELETE button
*tone button #pause button
HANDSET LAYOUT
EXIT button
MUTE/program button
MEM button

8
BASE LAYOUT
HANDSET CHARGE CRADLE LAYOUT
in use/
page
charge
page
page button/indicator
in use/page indicator
charge indicator
Back Side
charge
charge indicator
AC power supply

9
PARTS CHECKLIST
Make sure your package includes the items shown here.
TELEPHONE JACK REQUIREMENTS
To use this phone, you need an RJ11C (CA11A) type
modular phone telephone jack, which might look like the
one pictured here, installed in your home. If you don’t
have a modular jack, call your local phone company to
find out how to get one installed.
Base Dual Handsets Belt clips Mounting
pedestal
AC power supply Telephone line
cord
I
N
T
9
wxyz
6
mno
3
def
8
tuv
5
jkl
2
abc
7
pqrs
4
ghi
1
0
oper
#
pause
*
tone
v
v
RINGER
PAGE
FLASH
REDIAL
talk
format
c
o
n
f
e
r
e
n
c
e
c
a
l
l
b
a
c
k
c
i
d
/
v
o
l
MUTE
program
MEM EXIT
D
E
L
E
T
E
I
N
T
9
wxyz
6
mno
3
def
8
tuv
5
jkl
2
abc
7
pqrs
4
ghi
1
0
oper
#
pause
*
tone
v
v
RINGER
PAGE
FLASH
REDIAL
talk
format
c
o
n
f
e
r
e
n
c
e
c
a
l
l
b
a
c
k
c
i
d
/
v
o
l
MUTE
program
MEM EXIT
D
E
L
E
T
E
charge
in use/
page
charge
page
Handset Charge Cradle
Modular
telephone
line jack
Wall plate

10
INSTALLATION
INSTALLATION NOTE: Some cordless telephones operate at frequencies that
may cause interference to nearby TVs, microwave ovens, and VCRs. To minimize
or prevent such interference, the base of the cordless telephone should not be
placed near or on top of a TV, microwave ovens, or VCR. If such interference
continues, move the cordless telephone farther away from these appliances.
Certain other communications devices may also use the 2.4 GHz frequency for
communication, and, if not properly set, these devices may interfere with each
other and/or your new telephone. Typical devices that may use the 2.4 GHz
frequency for communication include wireless audio/video senders, wireless
computer networks, multi-handset cordless telephone systems, and some long-
range cordless telephone systems.
•Never install telephone wiring during a lightning storm.
•Never install telephone jacks in wet locations unless the jack is
specifically designed for wet locations.
•Never touch non-insulated telephone wires or terminals, unless the
telephone line has been disconnected at the network interface.
•Use caution when installing or modifying telephone lines.
•Temporarily disconnect any equipment connected to the phone such as
faxes, other phones, or modems.
INSTALLATION GUIDELINES
•Install telephone near both a telephone (modular) jack and an electrical
power outlet.
•Avoid sources of noise, such as a window by a busy street, and electrical
noise, such motors, microwave ovens, and fluorescent lighting.
•Avoid heat sources, such as heating air ducts, heating appliances,
radiators, and direct sunlight.
•Avoid areas of excessive moisture or extremely low temperature.
•Avoid dusty locations.
•Avoid other cordless telephones or personal computers.

11
INSTALLING THE PHONE
Choose the best location to install your base and handset charge cradle.
Your base and handset charge cradle should be placed on a level surface
such as a desk or table top, or you may mount the base on a wall.
CONNECTING THE AC (ELECTRICAL) POWER
1. On the base, plug one end of the power supply cord into the power jack
on the back of the base and the other end into an electrical outlet.
CAUTION: Use only the ATLINKS USA, Inc. power supply 5-2509
(white) or 5-2512 (black) that came with this unit. Using other power
supplies may damage the unit.
2. Plug the handset charge cradle into an electrical outlet.
NOTE: The charge indicator on the base and the charge indicator on the
handset charge cradle turns on to indicate the handset battery is charging.
CONNECTING THE TELEPHONE LINE
On the base, plug the one end of the telephone line cord into the jack on
the back of the base and the other end into a modular wall phone jack.
charge

12
INSTALLING THE HANDSET BATTERY
NOTE: You must connect the handset battery before use.
1. Push down on the top of the battery compartment cover (located on the
back of each handset) and remove the cover.
2. Lift the battery pack and connect it's plug to the jack inside the
compartment.
NOTE: It is important to maintain the polarity (black and red wires) to the
jack inside the compartment as shown in the illustration.
3. Close the battery compartment by pushing the cover up until it snaps
into place.
4. Place the handsets in the charging cradles.
Allow handsets to charge for 16 hours prior to first use. If you don’t
properly charge the handsets, battery performance is compromised.
WALL MOUNTING THE BASE
NOTE: For best results, leave the base on a flat surface during initial charging
before you hang it on the wall.
1. Turn the base over.
2. Attach the wall mounting pedestal by first inserting the tabs on the open
edge of the pedestal into the slots on the lower portion of the bottom of
the base.Then push down and snap the pedestal into place.
3. Slip the mounting holes (on the back of the pedestal) over the wall plate
posts and slide the unit down into place. (Wall plate not included.)
BLACK WIRE
RED WIRE
BATTERY
PRESS DOWN
FIRMLY

13
PROGRAMMING THE TELEPHONE
STANDBY SCREEN
The handset displays the handset number and user name.
PROGRAMMABLE FUNCTIONS
There are eight programmable menus available:
Language, Handset Name, Area Code, RingerTone,Tone/Pulse,
Registration, Deregistration, and Default Setting.
LANGUAGE
1. Make sure your phone is OFF (not in talk mode).
2. Press the MUTE/program button to go to the SET LANGUAGE menu.
3. Use the touch tone pad on the handset to select 1ENG, 2FRA, 3ESP, or
use the cid/ vol (up or down arrow) button to scroll to the desired
language. (English is the default setting).
4. Press the MUTE/program button to save your selection.You will hear a
confirmation tone.
NOTE: Press the EXIT button once to keep the previous setting and return to
the standby screen.
HANDSET NAME
1. Press the MUTE/program button to go to the HANDSET NAME menu.
2. Use the touch-tone pad to enter a name (up to 15 characters). More than
one letter is stored in each of the number keys. For example, to enter Bill
Smith, press the 2 key twice for the letter B. Press the 4 key 3 times for the
letter I. Press the 5 key 3 times for the letter L. Press the 5 key 3 times for
the second letter L, and press the 1 key to insert a space between the first
and last name. Press the 7 key 4 times for the letter S; press the 6 key once
for the letter M; press the 4 key 3 times for the letter I; press the 8 key for
the letterT; press the 4 key twice for the letter H.
USER NAME
HANDSET X

14
NOTE: If you make a mistake, use the delete/flash button to backspace and
delete one character at a time.
3. Press the MUTE/program button to save your name.You will hear a
confirmation tone.
AREA CODE
1. Press the MUTE/program button to go to the SET AREA CODE menu.
The default is - - -.
2. Use the touch-tone pad to enter your 3 digit area code.
3. Press the MUTE/program button to save your selection.You will hear a
confirmation tone.
NOTE: Press the EXIT button once to keep the previous setting and return to
the standby screen.
RINGER TONE
You may choose from six different ringer tones.
1. Make sure the ringer is turned on. See Ringer On/Off section.
2. Press the MUTE/program button to go to SET RINGERTONE menu.
3. The default ringer tone is set to ringer tone 1.
4. Use the touch-tone pad to enter a ringer tone number (1 through 6) , or use
the cid/vol (up or down arrow) button to scroll to the desired setting.You
will hear a sample of the ringer tone you select.
5. Press the MUTE/program button to save your selection.You will hear a
confirmation tone.
NOTE: Press the EXIT button once to keep the previous setting and return to
the standby screen.
TONE/PULSE
Most telephone systems use tone dialing, however, some may still use
pulse dialing.This system is pre-set to tone dialing. Depending on your
service type, set the dialing mode as follows:

15
1. Press the MUTE/program button to go to SETTONE/PULSE menu.
2.The default dialing mode is set toTONE.
3. Use the touch-tone pad to select 1 forTONE dialing or 2 for PULSE
dialing, or use the cid/vol (up and down arrow) button to scroll to
1TONE or 2PULSE dialing.
4. Press the MUTE/program button to save your selection.You will hear a
confirmation tone.
NOTE: Press the EXIT button once to keep the previous setting and return to
the standby screen.
If you aren't sure which dialing system you have, set the telephone to tone
dialing and make a test call. If the call connects, the setting is correct. If the
call does not connect, set the telephone to pulse dialing.
REGISTRATION
This setting may be made with the handsets only.Your dual handsets are
pre-registered and ready to use. It is not recommended that handset be
registered again unless absolutely necessary.
1. If necessary, press the MUTE/program button to go to the
REGISTRATION menu.The default is 2 NO.
2. Use the touch-tone pad to select 1 for YES or 2 for NO. Or use the cid/
vol (up and down arrow) button to scroll to 1 YES or 2 NO.
3. If you select 1YES, press the MUTE/program button to confirm your
selection. HOLD BASE PAGE WAIT FOR BEEP shows in the display.
4. Press and hold the page button on the base unit until you hear a long
tone at the handset. HANDSET X REGISTERED shows in the handset
display, where X is the handset name.You will hear a confirmation tone.
NOTE: Press the EXIT button once to keep the previous setting and return to the
standby screen. Or press and hold the EXIT button to return to standby mode.
NOTE: After you register a unit, HANDSET NAME menu automatically shows
in the display and prompts you to enter the handset name. For more
information, please refer to HANDSET NAME section of this manual.

16
DE-REGISTRATION
This setting may be made with the handsets only. Deregistration cancels
registration. During the de-registration process, keep the handset near
the base.
1. If necessary, press the MUTE/program button to go to the
DEREGISTRATION menu.The default is 2 NO.
2. Use the touch-tone pad to select 1 for YES or 2 for NO. Or use the cid/
vol (up and down arrow) button to scroll to 1YES or 2 NO.
WARNING: It is not recommended that a handset be de-registered unless
absolutely necessary because once a handset is de-registered, that handset's
telephone features cannot be used until the handset is re-registered.
3. Select NO, if you do not want to deregister.
4. If you select 1YES, press the MUTE/program button and MOVE NEAR
TO BASE displays for 2 seconds, then CONFIRM? 1YES 2 NO appears in
the display.
NOTE: Press the EXIT button once to keep the previous setting and return to
the standby screen.
5. Press the touch-tone pad to select 1YES or 2 NO, or use the cid/vol (up
and down arrow) button to scroll to 1YES or 2 NO.
6. If you selectYES, press the mute/program button to confirm. DE-
REGISTER ..... shows in the display followed by a confirmation tone.
Then HANDSET X DEREGISTERED shows in the display to confirm the
handset is deregistered.
NOTE: When you complete the deregistration process, HANDSET NEEDS
REGISTRATION shows in the display. To use the handset, you must register
the handset.
GLOBAL DE-REGISTRATION
If one or more handsets becomes lost, you should de-register all handsets
to ensure proper system operation. Follow the steps below to deregister
both handsets at the same time.

17
WARNING: It is not recommended that a handset be de-registered unless
absolutely necessary because once a handset is de-registered, that handset's
telephone features cannot be used until the handset is re-registered.
1. Press and hold the page button on the base until the IN USE/PAGE
indicator on the base flashes.
2. Press and hold the page button on the base again until the IN USE/PAGE
indicator on the base flashes rapidly.
3. Press and release the page button on the base once. All handsets are de-
registered and HANDSET NEEDS REGISTRATION shows in the display.
DEFAULT SETTING
As you become familiar with this system, you may prefer to use the
system’s original settings. Follow the steps below to return to the factory
default settings.
1. Press the MUTE/program button to go to the DEFAULT SETTING menu.
The default setting is 2 NO.
2. Use the touch-tone pad to select 1YES or 2 NO, or use the cid/vol (up or
down arrow) button to move the cursor to 1YES or 2 NO.
NOTE: If you choose “YES” all the settings in the programmable menu are
returned to factory default setting.
3. Press the MUTE/program button to save your selection.
NOTE: Press the EXIT key once to keep the previous setting and return to the
standby screen.
TELEPHONE OPERATION
CHARGE INDICATOR
When the charge indicator is lit, the handset is correctly seated in the cradle
and is charging.
MAKING CALLS
1. Pick up the handset, and press the talk/callback button. Listen for a
dial tone.

18
2. Dial the number you want to call, or dial the number first then press the
talk/callback button.
3. When finished, press the talk/callback button to hang up.
ANSWERING CALLS
1. When the phone rings, pick up the handset, and press the talk/callback
button.
2. When finished, press talk/callback to hang up.
NOTE: Adjust the handset volume by pressing the cid/vol (up or down arrow)
button during a call.
CALL TIMER
After you press the talk/callback button on the handset, the built-in call timer
shows on the display and counts the length of time of the call in minutes
and seconds.
PRE-DIALING
1. Make sure the phone is OFF (not in talk mode).
2. Enter the telephone number you want to call.The telephone number
shows in the handset display.
3. Press the talk/callback button on the handset, and the number
automatically dials.
NOTE: You may enter up to 32 pre-dial digits.
NOTE: If you want to delete the pre-dial number you entered, press the
FLASH/DELETE button until all of the digits are erased.
AUTO STANDBY
If you place the handset in the cradle while the handset is off the hook
(during a call), the call is automatically disconnected.
RINGER ON/OFF
The handset ringer toggle button is pre-set to ON.

19
1. Press the ringer button on the handset and RINGER ON 1ON 2 OFF
shows in the display (if the original ringer setting is ON).
2. Use the touch-tone pad to select 1ON or 2 OFF, or use the cid/vol (up or
down arrow) button to select 1ON or 2 OFF
3. Press the MUTE/program button to save your selection, or press the
EXIT key to retain the original setting.
NOTE: When the handset is set to RINGER OFF, the ringer off icon displays
continuously until the ringer is turned on.
FLASH/CALL WAITING
If you subscribe to the combined Call Waiting Caller ID service from your
local telephone company, you will receive Caller ID information (if available)
on Call Waiting calls. During a phone call, you will hear a beep to indicate
another call is waiting on the line and Caller ID information for the waiting
call shows on the handset display.
•To connect to the waiting call, press the flash button on the handset,
and your original call is put on hold.
•To switch between the two calls, press the flash button.
TIP: Don’t press the talk/callback button on the cordless handset to activate a
custom calling service, such as call waiting, or you’ll hang up the phone.
LAST NUMBER REDIAL
To quickly redial the last number you dialed:
1. Press the talk/callback button.
2. Press the REDIAL button.
-OR-
3. Press the REDIAL button first, then press the talk/callback button. If you
get a busy signal and want to keep dialing the number, press the
REDIAL button to quickly redial the number.
EXIT
Press the EXIT button to exit a menu function and return to the
standby screen.

20
PAGE
The page feature helps you locate a misplaced handset.To send and receive
pages, all handsets must be registered. If your handset is not registered,
follow the instructions in the Registration section of this manual.
HANDSET TO HANDSET PAGING
Dual handsets are respectively named as Handset 1 and Handset 2.
1. Make sure the phone is OFF (not in talk mode).
2. Press and release the PAGE/INT button on a handset. PAGING
EXTENSION? shows in the display.
3. Use the touch-tone pad to enter the handset number you want to page.
4. To cancel the page, press the EXIT button, or press the PAGE/INT button.
Or you may press talk/callback on the receiving handset.
PAGING FROM THE BASE/GROUP PAGE
Use the base-only to page both registered handsets at the same time.
1. Press the page button on the base. Both handsets beep for two minutes,
and PAGING FROM BASE shows on each handset’s display.
2. To cancel the page, press the page button on the base, or press the talk/
callback button on each handset.
MUTE
To have a private, off-line conversation, use the MUTE feature.The party
on the telephone line cannot hear you, but you can hear them.
1. Press the MUTE/program button.The handset display shows MUTE ON.
2. Press the MUTE/program button to cancel and return to your phone
conversation.
TEMPORARY TONE DIALING
This feature is useful only if you have pulse dialing service.Temporary
Tone Dialing enables pulse (rotary) service phone users to access touch-
tone services offered by banks, credit card companies, etc. For example,