GE VG4241 User manual

VCR User’s Guide
VG4241
We bring good things to life.

IMPORTANT INFORMATION
To reduce the risk of electric shock, do
not remove cover (or back). No user
serviceable parts inside. Refer servicing to
qualified service personnel.
This symbol indicates
"dangerous voltage"
inside the product that
presents a risk of electric
shock or personal injury.
This symbol indicates
important instructions
accompanying the
product.
WARNING
RISK OF ELECTRIC SHOCK
DO NOT OPEN
Caution: To reduce the risk of electric shock, match
wide blade of plug to wide slot, fully insert.
Attention: Pour éviter les chocs électriques,
introduire la lame la plus large de la fiche dans la
borne correspondante de la prise et pousser jusqú
au␣ fond.
Refer to the identification/rating label located on the back panel of your
product for its proper operating voltage.
FCC Regulations state that unauthorized changes or modifications to this
equipment may void the user’s authority to operate it.
Cable TV Installer: This reminder is provided to call your attention to
Article 820-40 of the National Electrical Code (Section 54 of the Canadian
Electrical Code, Part 1) which provides guidelines for proper grounding
and, in particular, specifies that the cable ground shall be connected to
the grounding system of the building as close to the point of cable entry
as practical.
WARNING
To reduce the risk of fire or
shock hazard, do not expose
this product to rain or moisture.
Product Registration
Please fill out the product registration card and return it immediately.
Returning this card allows us to contact you if needed.
Keep your sales receipt to obtain warranty parts and service and for
proof of purchase. Attach it here and record the serial and model
numbers in case you need them. The numbers are located on the back
of the product.
Model No.
Serial No.
Purchase Date:
Dealer/Address/Phone:
VG4241

TABLE OF CONTENTS
1
7
First Things First ..................................................3
Setting Up the VCR..............................................7
Using the Menu to Set Up Features....................................... 8
Language ...........................................................................8
Cable Box Setup ................................................................ 8
To Auto Channel Search .................................................. 10
To Change the SignalType .............................................. 11
To ADD or REMOVE Channels ........................................ 11
Time and Date ....................................................................... 12
Set Daylight-SavingTime ................................................ 12
Set theTime and Date ..................................................... 13
Additional Set-up Features In the Preferences Menu ......... 14
Remote VCR1/VCR2 Option ............................................. 14
Auto Play .......................................................................... 15
AutoTV/VCR ..................................................................... 15
EnergySaverTM ................................................................. 16
Tape Speed....................................................................... 16
VCR Basics ........................................................ 17
Remote Buttons ..................................................................... 18
Playing aTape ........................................................................ 19
Automatic Rewind ................................................................. 20
Tape Eject ............................................................................... 20
Recording ............................................................................... 20
Check the SafetyTab ........................................................20
Recording .......................................................... 21
Recording Features ............................................................... 22
Express Recording........................................................... 22
Timer Recording .............................................................. 23
Stopping aTimer Recording ..................................... 24
Review and Clearing Programs ................................ 24
Recording Broadcast StereoTV or SAP ............................... 25
Recording Audio Only ..................................................... 25
Playing Back Audio Only ................................................. 26
UsingTwoVCRs for Copying and EditingTapes.................. 26

TABLE OF CONTENTS
2
Other Features ................................................... 27
Picture Search Options .........................................................28
Forward and Reverse Search.......................................... 28
Slow Motion ....................................................................28
Commercial Scan (Search Button) .................................28
Frame Advance ................................................................29
Index Search .................................................................... 29
Zero Search ......................................................................30
Pro-Tect PlusTM Locking Feature ........................................... 30
Time Counter .........................................................................31
On-Screen Displays ...............................................................31
Tracking ..................................................................................32
Audio Set-up Features .......................................................... 32
Reception .........................................................................33
Tape Playback .................................................................. 33
Connections ....................................................... 35
ConnectingYour VCR .............................................................36
Jacks and Cables .............................................................36
RF Jacks and Antenna Cables (F-type) ...........................36
Audio/Video Jacks and Cables (RCA-type) ....................36
Choosing a VCR Connection ..........................................37
Advantages of Audio/Video Cable Connections ...........37
Don’t Forget About the AutoTV/VCR Feature................ 37
TV With RF Jack Only ............................................................ 38
TV With Audio/Video Jacks ................................................... 39
TV With Audio/Video Jacks and Cable Box
to Unscramble Pay Channels Only ................................ 40
References......................................................... 41
Front Panel .............................................................................42
Back Panel ..............................................................................43
Indicator Panel .......................................................................43
TroubleshootingTips ............................................................. 44
Specifications ........................................................................47
Cleaning the VCR ...................................................................47
Limited Warranty ...................................................................48
Index .......................................................................................49

FIRST THINGS FIRST
3
Hi, my name is Roger...
and I wrote this User’s Guide. It’s my job to see that
you have a rewarding user manual experience. You’ll
find that I’ve arranged this manual to clearly explain
all your VCR’s features.
Read the First Three Sections
The first three sections of the manual introduce you to
your VCR, and show you how to set the VCR up and
use the on-screen menus. Reading these sections
gives you the basic information you need to use your
VCR.
What’s Left?
The rest of the book highlights playback and recording
information, contains a detailed connections section,
and a reference section that includes troubleshooting
tips, limited warranty, and index. 5
READ ME!
These note boxes give you tips for
your new video cassette recorder.
➣➣
SETTING UP THE VCR
2
FIRST THINGS FIRST
1
➣
RECORDING
3VCR BASICS
4
➣
OTHER FEATURES
6
5
7
CONNECTIONS
➣

FIRST THINGS FIRST
4
STEP 1: Unpack What’s in the Box
The following items come packed in the box:
•VCR
• Remote control
• RF antenna cable
STEP 2: Install Batteries in the
Remote Control
Follow these steps whenever you need to install or change the
batteries in your VCR remote.
1. Remove the cover of the battery compartment.
2. Place batteries in remote, matching the + and – ends of each
battery to the diagram inside the compartment.
3. Replace the cover.
STEP 3: Connect Your VCR
If you connect your VCR to your home antenna or cable system
and then to your TV, use the VCR’s IN FROM ANT. and OUT TO TV
jacks for a good signal as shown.
If you have a TV with AUDIO/VIDEO jacks, use these jacks for a
better connection. In order to hear stereo and hi-fi sound from
the VCR, the audio/video jacks must be used. Refer to the
Connections section, toward the back of the manual.
STEP 4: Plug In the VCR
Match the wide blade of the plug with the wide slot in the outlet.
Be sure to insert the plug completely.
VCR
TV
CABLE/
ANTENNA
CABLE, CABLE BOX, OR ANTENNA
3 CH. 4
IN FROM
ANT.
VIDEO
OUT
R-AUDIO-L
OUT TO TV
VHF/UHF
MONO
IN 1

FIRST THINGS FIRST
5
VCR Viewing Channel
When using the ANTENNA jacks to
connect your VCR, tune your TV to
channel 3 or 4.
When using the audio/video jacks to
connect your VCR, tune your TV to the
TV’s video input channel.
STEP 5: Tune the TV
Tune the TV to the VCR viewing channel. The VCR viewing
channel is channel 3 or 4 or the TV’s video input.
• If you connect yourVCR using the ANTENNA connectors
with RF coaxial cable, set the 3CH.4 switch to channel 3 or
channel 4—the channel you want to use on yourTV.
• If you connect yourVCR using the AUDIO/VIDEO jacks with
audio/video cables, select theTV’s video input to see the
signal. See the TV Owner’s Manual .
STEP 6: Turn On the VCR
Press POWER to turn on the VCR.
STEP 7: Interactive Setup
The first time the VCR is turned on, Interactive Setup—a brief
series of on-screen menus—appears.These menus assist in
setting up several of the VCR’s features. Use the remote’s
number buttons to select options.
1. Press 1 for English, 2 for Español (Spanish), or 3 for Français
(French).
Select a language.
Seleccione un idioma.
Choisissez une langue.
1>English
2 Espanol
3 Francais
˜
˜
The remaining Interactive Setup menus will appear in the
language you choose. Follow the on-screen instructions to
complete the process.

FIRST THINGS FIRST
6
STEP 8: Access the Menus
When you’ve completed Interactive Setup, try out the VCR’s
regular on-screen menus.The MENU and number buttons let you
access, select, and change menu items. For example, to change
the Auto Play setting, you would do the following:
1. Press MENU to bring up the VCR MAIN MENU.
VCR MAIN MENU
1 Timer Recordings
2 Time
3 Channels
4 Preferences
5 Audio
6 Language
0 Exit
2. Press 4 to display the PREFERENCES menu .
PREFERENCES
1 Remote Control: VCR1
2 Auto Play: ON
3 Auto TV/VCR ON
4 EnergySaver: 2:00
5 Tape Speed: SLP
0 Exit
3. Press 2 to switch AUTO PLAY to ON or OFF.
PREFERENCES
1 Remote Control: VCR1
2 Auto Play: OFF
3 Auto TV/VCR ON
4 EnergySaver: 2:00
5 Tape Speed: SLP
0 Exit
See Setting Up the VCR for detailed information about the
Auto Play feature. Once you understand how to use the
menus, move on to the next section.

7
SETTING UP THE VCR
➣➣
SETTING UP THE VCR
FIRST THINGS FIRST
1
➣
RECORDING
3VCR BASICS
4
➣
CONNECTIONS
6
SPECIAL FEATURES
5
➣
Set-up Features
Below is a list of features that you can customize using
the on-screen menus.
• Select a language
• Set up VCR channel list (AUTO CHANNEL
SEARCH)
• Set up for a cable box
• Set automatic daylight-saving time
• Set the time and date
• Set the REMOTE VCR1/VCR2 feature
• Set the AUTO PLAY feature
• Set the AUTOTV/VCR feature
• Set the EnergySaverTM feature
• Set the preferredTape Speed
2

8
SETTING UP THE VCR
Using the Menu to Set Up Features
You can change the setup of the VCR’s features using the menu
system. Each feature is explained in this section.
Language
Select your preferred language, and the on-screen displays will
appear in that language.
1. Press MENU to display the VCR MAIN MENU.
VCR MAIN MENU
1 Timer Recordings
2 Time
3 Channels
4 Preferences
5 Audio
6 Language
0 Exit
2. Press 6 to select and display the LANGUAGE menu.
LANGUAGE
Select a language.
1>English
2 Espanol
3 Francais
Press MENU to contiune
˜
˜
3. Select English, Español (Spanish), or Français (French).
Cable Box Setup
This setup applies only when all channels are received through
the cable box. The VCR will automatically enter the output
channel of the cable box when programming your VCR for timer
recordings.
On-screen Menus
Not all the VCR screens are shown
in this manual when explaining
the features.

9
SETTING UP THE VCR
1. Press MENU to display theVCR MAIN MENU.
VCR MAIN MENU
1 Timer Recordings
2 Time
3 Channels
4 Preferences
5 Audio
6 Language
0 Exit
2. Press 3 to display the CHANNELS menu.
CHANNELS
1 Auto Channel Search
2 Add/Remove Channels
3 Signal Type: CABLE
4 Cable Box Setup
0 Exit
3. Press 4 to display CABLE BOX SETUP.Then select one of the
three choices.
CABLE BOX SETUP
Do you use your cable
box to receive ALL
channels or only SOME
channels.
1 ALL channels
2 Only SOME channels
3 Cancel setup
4. If you select ALL CHANNELS, enter the output channel of
your cable box, usually 03, 04, or video line input and
press␣ MENU.
CABLE BOX SETUP
On what channel does
the VCR receive signals
from the cable box?
(usually 3, 4, or Video)
04
Enter 01-13 or INPUT
Press MENU to cancel
Once you complete the setup, the VCR confirms that Cable
Box Setup is complete.
The VCR begins scanning for the available channels—this
VCR CHANNELS LIST
All Channels
If you do not use a cable box for ALL
channels, then you will want to use a
channel list (Auto Channel Search).
CABLE BOX SETUP
The VCR will now
receive all signals
from the cable box
on channel 04.
Press MENU to continue
Cable Box Setup
ALL CHANNELS: enter two numbers
for output channel of your cable box or
press INPUT.
ONLY SOME CHANNELS: If you only
use the cable box to tune premium
channels.
CANCEL SETUP: select to cancel.

10
SETTING UP THE VCR
VCR Channel List
Your VCR may come with a channel list preset at the factory.
Even though your VCR may come with a list, it’s possible that
you may want to add or eliminate some channels depending on
whether they are active.
To AUTO CHANNEL SEARCH
1. Press MENU to display theVCR MAIN MENU.
VCR MAIN MENU
1 Timer Recordings
2 Time
3 Channels
4 Preferences
5 Audio
6 Language
0 Exit
2. Press 3 to display the CHANNELS menu.
CHANNELS
1 Auto Channel Search
2 Add/Remove Channels
3 Signal Type: CABLE
4 Cable Box Setup
0 Exit
3. Press 1 to display the AUTO CHANNEL SEARCH menu.
AUTO CHANNEL SEARCH
What type of signal
are you using?
1 Cable TV
2 Antenna
3>Detect Automatically
0 Cancel
4. Select one of the three AUTO CHANNEL SEARCH options.
Choices one and two are self-explanatory. If you choose
DETECT AUTOMATICALLY, the VCR automatically detects
which signal system you have attached to your VCR.
Detect Automatically
A strong cable or antenna signal in
your area may cause Auto Detect to
mis-detect. If this should happen,
select 1 or 2 for the system you have.
Auto Channel Search
Use the Auto Channel Search feature
to place all available channels in
memory.
If you ever change cable or antenna
signals, you may need to Auto
Channel Search again.

11
SETTING UP THE VCR
AUTO CHANNEL SEARCH
Now scanning channel 14
Press any key to cancel
The VCR begins scanning for the available channels—this
takes about one to two minutes.The lowest channel is tuned
once the search is complete. Now, pressing CHANNEL up or
down should only select the active channels.
To Change the Signal Type
1. Press MENU to display theVCR MAIN MENU.
2. Press 3 to display the CHANNELS menu.
3. Press 3 to change the SIGNALTYPE between CABLE and
ANTENNA.
To ADD or REMOVE Channels
You may want to add or remove channels after you AUTO
CHANNEL SEARCH, especially if some of the channels have weak
signals or you don’t want to watch them.
1. Press MENU to display theVCR MAIN MENU.
2. Press 3 to display the CHANNELS menu.
3. Press 2 to display the ADD/REMOVE CHANNELS screen. Use
CHANNEL up or down or number buttons to go to the
channels you want to remove or add.
ADD/REMOVE CHANNELS
Channel 115
is presently ADDED
Press CLEAR to remove
Press MENU to exit
Selecting Channels
The CHANNEL up and down buttons
access those channels active in your
VCR channel list.
You can still access channels not in
the channel list by using the number
buttons on the remote control.
ADD/REMOVE CHANNELS
Channel 115
is presently REMOVED
Press INFO to add
Press MENU to exit

12
SETTING UP THE VCR
Spring forward; Fall backward
In the Spring, daylight-saving time
begins on the first Sunday in April.
Because the clock automatically
changes from 2:00 AM to 3:00 AM
(forward one hour), remember to
include the extra hour for timer
recording that falls within this time
frame.
In the Autumn, daylight-saving time
ends on the last Sunday in October.
The VCR clock automatically changes
from 2:00 AM to 1:00 AM (back one
hour).Therefore, it can affect your
recording length.
Time and Date
Before you set the time and date, set the AUTO DST (Daylight-
Saving Time) feature to ON or OFF for your area.
Set Daylight-Saving Time
1. Press MENU to display theVCR MAIN MENU.
VCR MAIN MENU
1 Timer Recordings
2 Time
3 Channels
4 Preferences
5 Audio
6 Language
0 Exit
2. Press 2 to display theTIME menu.
TIME
1 Set Time and Date
2 Auto DST: ON
0 Exit
3. Press 2 to turn AUTO DST: ON or OFF.
• Select ON if you want the VCR’s clock to automatically adjust
for daylight-saving time.
• Select OFF if you do not want the VCR’s clock to adjust for
daylight-saving time.

13
SETTING UP THE VCR
Set the Time and Date
1. Press MENU to display theVCR MAIN MENU.
VCR MAIN MENU
1 Timer Recordings
2 Time
3 Channels
4 Preferences
5 Audio
6 Language
0 Exit
2. Press 2 to displayTIME menu.
TIME
1 Set Time and Date
2 Auto DST: ON
0 Exit
3. Press 1 to display the SET TIME AND DATE screen.
SET TIME AND DATE
Time --:--
(hh:mm)
Date --/--/--
Press MENU to cancel
4. Enter the data using the number buttons. Press 0 before
single-digit numbers and follow the on-screen directions.
SET TIME AND DATE
Time 12:34 PM
Date 10/24/98 Friday
Press CLEAR to correct
Press MENU to set
Time/Date Display
Pressing INFO on the remote
displays the time and date on the
TV screen.
Time and Date
The time and date must be set
before a timer recording can be
programmed.

14
SETTING UP THE VCR
What’s Next—Additional Set-up
Features In the Preferences Menu
The features in this section are all accessed through the
PREFERENCES menu.
1. Press MENU to display the VCR MAIN MENU.
VCR MAIN MENU
1 Timer Recordings
2 Time
3 Channels
4 Preferences
5 Audio
6 Language
0 Exit
2. Press 4 to display the PREFERENCES menu.
PREFERENCES
1 Remote Control: VCR1
2 Auto Play: ON
3 Auto TV/VCR OFF
4 EnergySaver: 2:00
5 Tape Speed: SLP
0 Exit
Now you are ready to select an item from the menu to set up.
Remote VCR1/VCR2 Option
If you own a compatible RCA, GE, or ProScan remote that has a
VCR2, VCR2•LD, or DVD•VCR2 button, this feature allows you to
set this VCR to respond to that button.
Press 1 to select the REMOTE CONTROL item. Then press the
VCR2, VCR2•LD, or DVD•VCR2 button to change.
PREFERENCES
1 Remote Control: VCR1
2 Auto Play: ON
3 Auto TV/VCR OFF
4 EnergySaver: 2:00
5 Tape Speed: SLP
0 Exit
PREFERENCES
1 Remote Control: VCR2
2 Auto Play: ON
3 Auto TV/VCR OFF
4 EnergySaver: 2:00
5 Tape Speed: SLP
0 Exit
Remote Control Option
Changing the Remote Control option
to VCR2 disables the remote that
came with your VCR.

15
SETTING UP THE VCR
Auto TV/VCR
PressingTV•VCR on the remote
will still switch between the VCR
and TV mode.
VCR mode:VCR indicator in the
display panel lights.
TV mode: VCR indicator turns off.
The VCR will only respond to the compatible remote’s VCR2,
VCR2•LD, or DVD•VCR2 button. If you change the remote setting
to VCR2, the remote that came with your VCR will no longer
control the VCR.
Use the compatible remote to change the remote setting back to
VCR1. Display the PREFERENCES menu, press 1, and then press
VCR1.Then the remote that came with the VCR will be able to
control it again.
Auto Play
This feature allows the VCR to automatically start playing when
you insert a tape with the safety tab removed. Press 2 to switch
between ON or OFF.
• Select ON if you want a tape with its safety tab removed to
start playing automatically when the tape is inserted.
• Select OFF if you do not want a tape with its safety tab
removed to start playing automatically.
Auto TV/VCR
This feature controls whether theTV/VCR switch changes
automatically to the VCR mode when the VCR is turned on. Press
3 to switch between ON and OFF.
• Select ON if you want the VCR to switch to the VCR mode
when the VCR is turned on or a cassette is inserted. This
only applies if you connect the IN FROM ANT. and OUTTOTV
jacks of your VCR andTV and watch your VCR on channel 3 or
4 of yourTV .
• Select OFF if you want the VCR to remain in theTV mode.
This is useful if you watch your VCR on theTV’s video input
and you don’t want your antenna/cable signal interrupted by
the VCR.

16
SETTING UP THE VCR
EnergySaverTM
By default, this VCR automatically turns off after two hours of
inactivity. Press 4 to change the time delay, or to disable the
feature.
• OFF: The VCR will remain turned on until you shut it off.
• 1:00, 2:00, or 3:00:The VCR turns off after one, two, or three
hours of inactivity.
Thirty seconds before shutting off, the VCR will warn you with a
screen reading, “The VCR will turn off in 30 seconds. Press any
key to cancel.”
If you use the VCR’s tuner instead of your TV to tune channels,
you may want to turn this feature off.
Tape Speed
You can select a preferred tape speed for recording.The speed
you select appears in the timer recording menu.The default
factory setting is SLP. Press 5 to switch between SP and SLP.
When making a recording, you can override the preferred tape
speed.
• Press the SPEED button on the remote.
• Set the tape speed in the timer or VCR Plus+ recording
menu.
When you turn off the VCR, the tape speed reverts to the one
you have selected.
Tape Speeds
SP (Standard Play)
Gives the best quality recording,
but fewer programs can be
recorded on the tape. Special
effects such as pause, slow
motion, picture search, and frame
advance work well when you play
back tapes recorded in this␣ speed.
LP (Long Play)
Your VCR is capable of playing
back tapes recorded in LP.You
cannot record in the LP speed.
SLP (Super Long Play)
Gives three times the recording
time of tapes recorded in SP.
Special effects such as pause, slow
motion, picture search, and frame
advance work well when you play
back tapes recorded in this speed.
Recording Time
Cassette SP SLP
T-120 2Hr 6Hr
T-160 2Hr 8Hr
40Min

17
VCR BASICS
Learn the Basics To Get
You Started
These VCR basics should be enough for you to
begin enjoying your VCR. Learning the remote
control functions, playing a recorded tape, and
recording a program should do just that.
However, there are other features that enhance the
enjoyment of your VCR, but they aren’t necessary
to get you started. If you want to learn more about
your VCR, just keep reading.
VCR Basics tells you what you
need to know in order to watch a
movie or tape your favorite show.
➣➣
SETTING UP THE VCR
2
FIRST THINGS FIRST
1
➣
RECORDING
3VCR BASICS
4
➣
OTHER FEATURES
6
5
7
CONNECTIONS
➣

18
VCR BASICS
Remote Buttons
CHAN Up or Down Selects next higher or lower channel in the
VCR’s channel memory.
CLEAR Resets time counter to 0:00:00. Allows you to change
entries when setting the clock or a timer recording.
F.ADV Lets you view one frame with each press of the button
when tape is in pause.
FWD Fast forwards the tape when theVCR is stopped. Searches
forward through a tape during playback. Increases speed of slow-
motion playback.
GO BACK Switches between two channels. Select one channel
and then select another using the number buttons. Press GO
BACK to switch between the two channels.
INFO Shows the status displays on theTV screen.
INPUT Selects between the line input andVCR’s tuner. Line input
refers to the signal coming from the component connected to the
audio/video input jacks on the back of the VCR.
MENU Brings up VCR MAIN MENU on theTV screen. Used to
select a menu item or exit a menu.
Numbers (0 through 9) Select a channel up to 99 by pressing
two numbers. Select a cable channel over 99 by pressing and
holding 1 until 1 – – appears on the screen.Then press the other
two numbers.
PAUSE Pauses playback or recording. Press PAUSE again to
return to playback or recording.
PLAY Plays a tape. Starts playback again from pause mode.
POWER Turns the VCR on and off.
RECORD Starts VCR recording. Also used for express recording.
REV Rewinds the tape when the VCR is stopped. Searches
backward through a tape during playback. Decreases slow-motion
playback.
SEARCH Displays INDEX and ZERO SEARCH menus onTV
screen when VCR is stopped. Advances the tape 30 seconds of
recorded material during playback.
SLOW Starts slow-motion playback.
SPEED Selects a recording speed (SP or SLP).
CLEAR
MENU
SPEED
INPUT
F.ADV
TRACKING
STOP
PLAY
123
546
79
8
0
PAUSE
SLOW SEARCH
RECORD
FWD
REV
POWER
INFO
TV•VCR GO BACK
CHAN
4
3
4
3