GE Monogram ZTD910SFSS User instructions

OVERALL DIMENSIONS
FRONT VIEW (SHOWING CUTOUT OVERLAP)
TOP VIEW
SIDE VIEW
1 3/32"
(2.8)
25 19/32" (65)
handle width
28 1/2" (72.4)
cutout width
30" (76.2)
10 1/2"
(26.7)
5/8"
(1.6)
9 1/4"
(23.5)
cutout height
9"
(22.9)
26" (66.0)
including handle
23 1/4" (59.0)22" (55.9)
27 15/16" (71.0)
23 1/4"
(59.0)
29/32"
(2.4)
2"
(5.1)
Dimensions in parentheses
are in centimeters unless
otherwise noted. Actual
product dimensions may
vary due to manufacturing
tolerances.
For more details refer to the installation instructions
for this product.
Product Specification Created 8/14
GE Monogram®30" Warming Drawer
SPECIFICATIONS
Overall Width 30" (76.2 cm)
Overall Height 10 1/2" (26.7 cm)
Overall Depth 23 1/4" (59.0 cm)
Drawer Capacity 1.90 cu. ft. (53.8 l)
Cut-out Width 28 1/2" (72.4 cm)
Cut-out Height 9 1/4" (23.5 cm)
Cut-out Depth 23 1/2" (59.7 cm)
Power Cord Length 56" (142.2 cm)
Electrical Rating 450W @ 120V/60Hz
Total Amps 15 Amps
Net Weight 59 lbs. (26.8 kg)
Approx. Shipping Weight 65 lbs. (29.6 kg)
OPTIONAL ACCESSORIES
Custom Panel Kit ZXD30B
Professional Panel Kit ZXD30P
ZTD910SFSS
ATTENTION ELECTRICIAN:
This appliance is supplied with a 56" (142.2 cm)
long electrical cord equipped with a 3-prong
(grounding) plug that mates to a standard
3-prong grounding wall outlet.
The electrical power cord is located on the right
side of the warming drawer. Locate the wall
outlet within easy reach of the electrical cord in
an adjacent cabinet, within 42" (106.7 cm) of the
right side or 16" (40.6 cm) from the left side of the
cut-out. A recessed outlet can be installed on the
right side of the cut-out, 7" (17.8 cm) max. from
the rear of the cabinet.
DO NOT USE AN EXTENSION CORD
WITH THIS PRODUCT.

NOTES
AWarming drawers
are approved for
installation below
only certain specified
wall oven and cooktop
models. See the label
attached to the top of
the warming drawer for
approved combinations.
BAdditional clearance
between cut-outs may
be required. Check to be
sure that oven supports
above the warming
drawer location do not
obstruct the required
interior 23-1/2" depth
and 9-1/4" height.
CIf you are installing in
frameless cabinets,
it may be necessary
to install 1/2" wide
cleats to accept drawer
mounting screws. See
drawer for mounting
screw locations.
DInstall a 2"x2" or 2"x4"
Anti-tip block against
rear wall, 9" from floor
of cutout to bottom
of block. The anti-tip
block must be installed
to prevent the drawer
from tipping forward
when opened and
loaded. Failure to add
the anti-tip block could
result in personal injury.
EWhen installing the
warming drawer
below a cooktop, a
solid barrier must be
installed at least 1"
from the lowest point of
the bottom of cooktop
burner box to the top
of the cut-out. Use any
solid material such as
1/4" thick plywood.
Allow at least 1/4"
air gap between the
barrier and the top of
the warming drawer.
For more details refer
to the installation
instructions for this
product.
INSTALLATION BELOW SINGLE OR DOUBLE WALL OVEN
INSTALLATION BELOW COOKTOP
Product Specification Created 8/14
GE Monogram®30" Warming Drawer ZTD910SFSS
SIDE VIEW FRONT VIEW
SIDE VIEW FRONT VIEW
28 1/2" (72.4)
min. cutout width
28 1/2" (72.4)
min. cutout width
2" (5.1)
min.
23 1/2" (59.7)
min. cutout depth
1" (2.5) min.
above toe-kick
or adjust to
oven height
9 1/4"
(23.5)
cutout height
TOP VIEW
Side cleats
23 1/2" (59.7)
min. cutout depth
5 1/2"
(14.0)
min.
From top of countertop
to top of warming
drawer cutout
1" (2.5) min.
above toe-kick
or adjust to
cooktop height
9 1/4"
(23.5)
cutout height
ZDT910SFSS
SIDE VIEW FRONT VIEW
SIDE VIEW FRONT VIEW
28 1/2" (72.4)
min. cutout width
28 1/2" (72.4)
min. cutout width
2" (5.1)
min.
23 1/2" (59.7)
min. cutout depth
1" (2.5) min.
above toe-kick
or adjust to
oven height
9 1/4"
(23.5)
cutout height
TOP VIEW
Side cleats
23 1/2" (59.7)
min. cutout depth
5 1/2"
(14.0)
min.
From top of countertop
to top of warming
drawer cutout
1" (2.5) min.
above toe-kick
or adjust to
cooktop height
9 1/4"
(23.5)
cutout height
ZDT910SFSS
A
C
C
C
BD
D
E

NOTES
AIf you are installing in
frameless cabinets,
it may be necessary
to install 1/2" wide
cleats to accept drawer
mounting screws. See
drawer for mounting
screw locations.
BInstall a 2"x2" or 2"x4"
anti-tip block against
rear wall, 9" from floor
of cutout to bottom
of block. The anti-tip
block must be installed
to prevent the drawer
from tipping forward
when opened and
loaded. Failure to add
the anti-tip block could
result in personal injury.
CWhen installing the
warming drawer below
a cabinet drawer, a
solid barrier must be
installed at least above
the warming drawer
to block access. Use
any solid material such
as 1/4" thick plywood.
Allow at least 1/4"
air gap between the
barrier and the top of
the warming drawer.
Observe the 5" min.
above the floor or 1"
min. above the toe kick
installation height.
DWhen installing two
warming drawers side
by side, install them
in separate cut-outs
and allow a 2" min. gap
between each cut-out.
EThe warming drawer
may be supported by
either a solid bottom or
2"x2" or 2"x4" runners.
The support must
be level and rigidly
mounted, flush with
the bottom edge of the
cut-out (there is no way
to level the drawer once
it has been installed,
so make sure that the
supports are level). The
floor or runners must be
capable of supporting
at least 150 lbs.
For more details refer
to the installation
instructions for this
product.
INSTALLATION BELOW A CABINET DRAWER
PROVIDING CABINET SUPPORT INSTALLING ANTI-TIP BLOCKS
SIDE BY SIDE INSTALLATION
Product Specification Created 8/14
GE Monogram®30" Warming Drawer ZTD910SFSS
SIDE VIEW FRONT VIEW
TOP VIEW
28 1/2" (72.4)
min. cutout width
23 1/2" (59.7)
min. cutout width
1/4"
(.6)
min.
1"
(2.5)
min.
Above
toe-kick
2" (5.1) min.
Between cut-outs
2" (5.1) x 4" (10.2)
or Equivalent Runners
Install
2" (5.1) x 4" (10.2)
or
2" (5.1) x 2" (5.1)
Anti-tip Block against
rear cabinet wall 9" from
floor to bottom of block
Side cleats
9 1/4"
(23.5)
Cut-out
height
30" (76.2)
25" (63.5)
23 1/2"
(59.7)
2" (5.1) x 4" (10.2)
or
2" (5.1) x 2" (5.1)
Runners or Solid Bottom
ZDT910SFSS
SIDE VIEW FRONT VIEW
TOP VIEW
28 1/2" (72.4)
min. cutout width
23 1/2" (59.7)
min. cutout width
1/4"
(.6)
min.
1"
(2.5)
min.
Above
toe-kick
2" (5.1) min.
Between cut-outs
2" (5.1) x 4" (10.2)
or Equivalent Runners
Install
2" (5.1) x 4" (10.2)
or
2" (5.1) x 2" (5.1)
Anti-tip Block against
rear cabinet wall 9" from
floor to bottom of block
Side cleats
9 1/4"
(23.5)
Cut-out
height
30" (76.2)
25" (63.5)
23 1/2"
(59.7)
2" (5.1) x 4" (10.2)
or
2" (5.1) x 2" (5.1)
Runners or Solid Bottom
ZDT910SFSS
SIDE VIEW FRONT VIEW
TOP VIEW
28 1/2" (72.4)
min. cutout width
23 1/2" (59.7)
min. cutout width
1/4"
(.6)
min.
1"
(2.5)
min.
Above
toe-kick
2" (5.1) min.
Between cut-outs
2" (5.1) x 4" (10.2)
or Equivalent Runners
Install
2" (5.1) x 4" (10.2)
or
2" (5.1) x 2" (5.1)
Anti-tip Block against
rear cabinet wall 9" from
floor to bottom of block
Side cleats
9 1/4"
(23.5)
Cut-out
height
30" (76.2)
25" (63.5)
23 1/2"
(59.7)
2" (5.1) x 4" (10.2)
or
2" (5.1) x 2" (5.1)
Runners or Solid Bottom
ZDT910SFSS
A
A
D
E
B
B
C

NOTES
This kit contains a
mounting panel to support
a trim-less custom drawer
front up to 3/4" thick. The
original tubular handle
can be reinstalled onto the
custom panel with longer
screws (not provided) or
can be replaced with a
custom handle of your
choice (also not provided).
For more details refer
to the installation
instructions for this
product.
INSTALLATION WITH CUSTOM PANEL KIT - ZXD27B
Product Specification Created 8/14
GE Monogram®30" Warming Drawer ZTD910SFSS
SIDE VIEW
CUSTOM PANEL PREPARATION
FRONT VIEW CUSTOM PANEL PREPARATION
SIDE VIEW
9"
(22.9)
23 5/16" (59.2)
including handle
Excluding
custom panel
Drawer
open
Excluding
custom panel
23 1/4" (59.0)24" (61.0)
10 1/2"
(26.7)
Drill
5/16" (0.8)
through custom
panel for lamp jewel
30" (76.2)
1 13/16" (4.6)
1 3/4" (4.5)
3/4" (1.9) max.

NOTES
This kit contains a
mounting panel to support
a trim-less custom drawer
front up to 3/4" thick. The
original tubular handle
can be reinstalled onto the
custom panel with longer
screws (not provided) or
can be replaced with a
custom handle of your
choice (also not provided).
For more details refer
to the installation
instructions for this
product.
INSTALLATION WITH PROFESSIONAL STYLE PANEL KIT - ZXD30P
Product Specification Created 8/14
GE Monogram®30" Warming Drawer ZTD910SFSS
FRONT VIEW (SHOWING CUT-OUT OVERLAP)
TOP VIEW
SIDE VIEW
10 1/2"
(26.7)
9"
(22.9)
9 1/4"
(23.5)
Cutou-out height
5/8"
(1.6)
2 1/4"
(5.7)
1 3/4"
(4.5)
2 13/16"
(7.1)
30" (76.2)
27 15/16" (71.0)
26" (66.0)
Handle width
28 5/16" (72.0)
Including Handle
28 1/2" (72.4)
Cut-out width
28 1/2" (72.4) 23 1/4" (59.0)
23 1/4"
(59.0)

FEATURES AND BENEFITS
R
Infinite Setting Temperature Control –
75 Degrees to 230 Degrees
Variable Humidity Control – Crisp to Moist
Removable Half Rack
1.9 cu. ft capacity
Accepts 3/4" trimless custom panel and custom
handle with trim kit
Full extension drawer on ball bearing glides
"On" indicator light
Accepts Optional Professional Panel Kit
Removable Stainless Steel Pan
Variable Installation Options
Hidden Controls Provide Flush Installation
Appearance
On/Off Rocker Switch
Product Specification Created 8/14
GE Monogram®30" Warming Drawer ZTD910SFSS