GE Monogram ZKD910BF User instructions

Specification Revised 1/08
130714
Monogram.
™
ZKD910BF/SF/WF – GE Monogram 27" Warming Drawer
For answers to your Monogram,
®GE Profile™or
GE appliance questions, visit our website at
GEAppliances.com or call
GE Answer Center®service, 800.626.2000.
Listed by
Underwriters
Laboratories
298Dia12
26"
Including Handle
23-1/4"
26-3/4"
10-1/2"
9"
1"
Drawer
Open
27"
Warming Drawer Dimensions (in inches)
298Dia14
1" Min. Above Toekick or Adjust
to Oven Installation Height
25-1/2"
2" Min.
Allow 5/8"
Overlap on
All Sides
26-3/4"
10-1/2"
23-1/4"
23-1/2" Min.
Inside
Oven
Cutout
9-1/4"
2x2 or 2x4
Anti-Tip Block
Against Rear
Wall, 9" From
Floor to
Bottom of
Block
9"
Single Oven Installation (in inches)
298Dia13
25-1/2"
2" Min.
Allow 5/8"
Overlap on
All Sides
26-3/4"
10-1/2"
23-1/4"
23-1/2" Min.
Inside
1" Min. Above Toekick
Oven
Cutout
2x2 or 2x4
Anti-Tip Block
Against Rear
Wall, 9" From
Floor to
Bottom of
Block
9"
9-1/4"
Double Oven Installation (in inches)
Note: Additional clearance between cutouts may be required.
Check to be sure that oven supports above the Warming
Drawer location do not obstruct the required interior 23-1/2”
depth and 9-1/4” height.
9"
2x4 or 2x2
Runners or Solid Bottom
Install
2x4 or 2x2
Anti-Tip Block
Against Rear
Cabinet Wall
9" From Floor
to Bottom
of Block
298Dia16

Specification Revised 1/08
130714
Monogram.
™
ZKD910BF/SF/WF – GE Monogram 27" Warming Drawer
For answers to your Monogram,
®GE Profile™or
GE appliance questions, visit our website at
GEAppliances.com or call
GE Answer Center®service, 800.626.2000.
Undercounter Installation (in inches)
Note: When installing warming drawer with a cooktop,
allow a 2" minimum from cooktop burner box bottom to
top of cut-out.
Important Installation Note:
Must provide anti-tip brace at the back of the cabinet and
at the top of the cutout.
Optional Accessories:
ZXD27B – 3/4" wood panel trim kit
*Note: When installing the warming drawer below a
cooktop, a solid barrier must be installed at 1” from the
lowest point of the bottom of cooktop burner box to the
top of cutout. Use any solid material such as 1/4” thick
plywood. Allow at least 1/4” air gap between the barrier
and the top of the warming drawer. See label on top of the
warming drawer for approved cooktop models.
Electrical
Outlet 16" Max.
From Left Side
Installation Below
a Drawer
23-1/2 Min.
Solid Barrier
1/4
Air Gap
25
1-1/2 Cabinet Top
36
Countertop
Height
1 Min.*
28-1/2
9-1/4
Electrical Outlet 42" Max.
From Right Side
Install a Solid Barrier
Below a Cooktop
See Note
Electrical Outlet
Flush With Side
of Cabinet 7" Max.
9
Install
2x4 or 2x2
Anti-Tip Block
Against Rear
Cabinet Wall
9" From Floor
to Bottom
of Block 7
Install a Solid Barrier
and a 1/4" Air Gap
Above Warming Drawer
• When installed, the front face of the drawer will be nearly flush
with adjacent cabinetry doors.
• Drawer overlaps will conceal cut edges on all sides of the opening.
The rough opening for the drawer must be:
–Depth 23-1/2" min. from inside back to front of cabinet frame.
–Width 25-1/2" for 27" wide models, 28-1/2" for 30" wide models.
–Height 9-1/4"
• 5" min. above floor or 1" above toekick. 23-1/4" from floor to bottom
of cutout is recommended for under countertop installation.
Installation below a cooktop:
Warming drawers are approved for installation below only certain
specified cooktop models. See the label attached to the top of the
warming drawer for approved models. A solid barrier and air gap
between cooktop and warming drawer is required. See Note above.
Installation below a cabinet drawer:
The warming drawer may be installed beneath a cabinet drawer. In
this installation, a solid barrier should be installed above the warming
drawer to block access. Use any solid material such as 1/4" thick
plywood. Allow at least 1/4" air gap between the barrier and the
top of the warming drawer. Observe the 5" min. above the floor or 1"
above the toekick minimum installation height.
Note: If you are installing in frameless cabinets, it may be necessary
to install 1/2" wide cleats to accept drawer mounting screws. See
drawer to find exact locations of mounting screws.
Side to Side Installation:
Install two warming drawers in separate cutouts. Allow 2" min.
between cutouts.
2
Min.
Side to Side Installation
Listed by
Underwriters
Laboratories

Specification Revised 1/08
130714
Monogram.
™
ZKD910BF/SF/WF – GE Monogram 27" Warming Drawer
ZKD910WB
Features and Benefits
• 1.92 cu. ft. Capacity
• Variable Temperature Control – Proof (80)/
Low (140)/Med (170)/High (210)
• Variable Humidity Control – Crisp to Moist
• Half Rack
• “On” Signal Light
• On/Off Rocker Switch
• Removable Stainless Steel Pan
• Full Extension Ball Bearing Glides
• Hidden Controls Provide Flush Installation
Appearance
• Variable Installation Options
• Pan Set Included
• Model ZKD910WFWW – White on white
• Model ZKD910BFBB – Black on black
• Model ZKD910SFSS – Stainless steel