GE Spacemaker WSLP1100D User guide

WSLP1100D – GE Spacemaker®Portable Washer
Dimensions (in inches)
Washer Note: Washer wall outlet must be located within 36" of service cord
entry. Wall outlet must not be located behind dryer.
Specification Revised 8/03
360436
For answers to your Monogram,®GE Profile™or
GE®appliance questions, visit our website at
GEAppliances.com or call
GE Answer Center®service, 800.626.2000.
R
Listed by
Underwriters
Laboratories
GE Appliances
38
23-5/8
26
SpacemakerDryer
PREWASH
NORMAL
WASH
RINSEONLY
SPINONLY
PREWASH
NORMAL
WASH
RINSEONLY
SPINONLY
COLORS
WHITES
DELICATES
QUICKWASH
LOADRINSING
HOT/COLD
WARM/COLD
COLD/COLD
TIME
REMAINING
MIN
CLOTHESCARECYCLESELECTION
WASH
OPTIONSLOAD
SIZEWASH
CYCLETEMP
WASSH/RINSE
START
PAUSE
POWER
ON/OFF

GE Appliances
WSLP1100D –GE Spacemaker®Portable Washer
Specification Revised 8/03
360436
20" Max.
Opening
120V 20Aor
208-240V 30A
3-3/4
3
3
Rear
Exhaust
5-1/8
8
74-1/8
78 74-1/8
Service
Cord
Entry at
Bank of
Appliances
R.H
EXH
5-1/8
4" Dia.
Exhaust
3-1/8
Both
Sides
33-1/4
38
79-1/4
32
2 x 4
2 x 4
624-1/2
DSKS433
DSKS333
WSLP1100
WSLS1100
Standpipe
33" Minimum
If Less Than 33"
Use Syphon
Break Kit
WH49X228
26
28
23-7/8
6
120V
15 or 20A
1-1/2
23-5/8
Standpipe
& Faucets
33" Min.
46
20" Max.
Opening
120V 20Aor
208-240V 30A
3-3/4
3
3
Rear
Exhaust
5-1/8
8
68-1/8
72 68-1/8
Service
Cord
Entry at
Bank of
Appliances
R.H
EXH
5-1/8
4" Dia.
Exhaust
3-1/8
Both
Sides
33-1/4
38
73-1/4
32
2 x 4
2 x 4
624-1/2
DSKS433
DSKS333
WSLP1100
Standpipe
33" Minimum
If Less Than 33"
Use Syphon
Break Kit
WH49X228
26
28
23-7/8
6
120V
15 or 20A
1-1/2
23-5/8
Standpipe
& Faucets
33" Min.
40
For answers to your Monogram,®GE Profile™or
GE®appliance questions, visit our website at
GEAppliances.com or call
GE Answer Center®service, 800.626.2000.
R
Listed by
Underwriters
Laboratories
Use this drawing when space will not allow for opening of
washer lid. Washer must be rolled forward for use.
Use this drawing when space allows for standard installation
with room for washer lid opening.

GE Appliances
WSLP1100D –GE Spacemaker®Portable Washer
Specification Revised 8/03
360436
WALL BRACKET
REAR VIEW FRONT VIEW
2 x 4
figure 1
figure 2
1/8" MAX
This kit consists of the following:
1 Wall mounting bracket
2 Bottom Brackets
6-1/4 x 3 inch wood screws
7-1/4 x 1-1/2 inch wood screws
12 washers
Dryer Requirements
Carefully read and follow individual
dryer installation instructions for
exhausting requirements.
GENERAL INFORMATION:
The back of the dryer is not accessible for service or maintenance after dryer mounting installation is
complete. It is recommended that the dryer be checked and electrical installation completed prior to
mounting. For service or maintenance requiring rear access, the dryer must be removed from the wall.
CAUTION: DISCONNECT ELECTRICAL CURRENT BEFORE INSTALLING OR SERVICING DRYER.
The electrical outlet must be located above the dryer, or beside the dryer if adequate dryer-to-wall clearance
is available. The outlet must be within three feet on a 240 volt dryer or a 120 volt dryer from the service cord
entry on the rear of the dryer.
DRYER MOUNTING POSITION
These instructions explain two mounting positions for your 24 inch dryer.
INSTALLATION PROCEDURE:
1. Obtain two pieces of 2x4 long enough to span at least two wall studs and the width of the dryer.
2. Locate wall stud center lines. Mark wall stud center lines on two pieces of 2x4 in relationship to
position dryer is to be mounted.
3. Referring to dimensional drawing, draw a horizontal reference line (78") from the floor to locate upper
2x4 support.
4. Position, level and secure upper 2x4 with four 1/4 x 3 inch wood screws. The bottom of the 2x4 should
be positioned on reference line.
5. Referring todimensional drawing,draw ahorizontalreferenceline 32"down from thebottom ofthe upper
2x4support.
6. Position, level and secure lower 2x4 with two 1/4 x 3 inch wood screws. The center line of the 2x4
should be positioned on reference line.
7. Referring to figure 1, mount the metal wall bracket 1/8 inch from the bottom of the upper 2x4 support
with five 1-1/2 inch wood screws.
8. Referring to figure 2, remove one screw from each lower rear corner of dryer and, using same screws,
secure lower brackets (supplied) as shown.
9. Dryer is supplied with exhaust at the top, locate and install outside exhaust duct referring to the
dimensional drawing. For other optional exhaust directions as shown in dimensional drawing
(rear and sides) refer to dryer installation instruction sheet.
10. Position the dryer on the wall mounting bracket and check that the dryer is plumbed.
11. If the dryer needs plumbing, use some of the twelve washers supplied with the kit as spacers behind
lower brackets of figure 2 and secure the dryer to the lower 2x4 support using the remaining 1-1/2 inch
wood screws.
WMK-35 Wall Kit Installation
CAUTION
The 120 volt receptacle on the back of the
240 volt dryer must not be used with this
wall mount kit.
Figure 1
Figure 2

Specification Revised 8/03
360436
WSLP1100D –GE Spacemaker®Portable Washer
Features and Benefits
•Electronic one-touch controls with LED read-out –Simplify cycle selection and provide
accurate cycle times.
•One-touch loading sensing –Eliminates guesswork and helps reduce water waste.
•Multiple wash cycles –Delivers optimal cleaning results.
•Three wash/rinse temperatures –Offer better wash results and longer fabric life.
•Multiple wash/spin speeds –Matches wash action to fabric type for better cleaning
and clothes care.
•Four water levels –Offers water and energy savings.
•Stainless steel basket –It resists rust and won’t chip, peel or snag clothes.
•Model WSLP1100DWH –White
•Model WSLP1100DWW –White on white
SpacemakerDryer
PREWASH
NORMAL
WASH
RINSEONLY
SPINONLY
PREWASH
NORMAL
WASH
RINSEONLY
SPINONLY
COLORS
WHITES
DELICATES
QUICKWASH
LOADRINSING
HOT/COLD
WARM/COLD
COLD/COLD
TIME
REMAINING
MIN
CLOTHESCARE CYCLESELECTION
WASH
OPTIONSLOAD
SIZEWASH
CYCLETEMP
WASSH/RINSE
START
PAUSE
POWER
ON/OFF
GE Appliances