GE WWA8995S User manual

Washer
Safe~ instructions ....................3, 4
Operating Instructions, Tips
Bleach Dispenser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Control Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..........6
CycleDescriptions.........................................5
Cycle Times . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..7
EndCycleSignal........................................6,7
Energy-SavingTips........................................8
Fabric Softener Dispenser ...........................8
Handwash” System . . . . . . . . 10
Operating the Washer ...........................6–l O
Suggested Fabric and Cycle Settings .......9
Care and Cleaning
Storage and Vacation Tips ........................2 1
User Maintenance Instructions ...............21
Problem solver ......................17-21
More questions ?...call
GE Answer Center
a
80~626.2000
Preparation
Detergents and Additives ...............,.. 13, 14
Hard Water . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Loading the Washer...............................7, 12
Sorting
Clothes........................................7, 11
Stains . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Stain Removal Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Consumer Services ..................23
Appliance Registration .................................2
Important Phone Numbers .......................23
Model and Serial Numbers .....................,....2
Repair Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .........Back Cover
I
Model
WA8995S
GE Apphances

~LP US ~LP YOU...
Read this book carefully.
It is intended to help you
operate and maintain your
new washer properly.
Keep it handy for answers to
your questions.
If you don’t understand something
or need more help, write (include
your phone number):
Save time and money.
Before you request service . . .
check the Problem Solver
section. It lists causes of minor
operating problems that you can
correct yourself.
If you received a
damaged washer...
Consumer Affairs Immediately contact the dealer (or
GE Appliances, Appliance Park
builder) that sold you the washer.
Louisville. KY 40225
To obtain a Spanish language Para
obtener la versi6n en
version of this book, call
espafiol de este manual, name a
GE Answer
Center@
GE Answer Center@, servicio de
800.626.2000
information para el consumidor,
consumer information service.
te16fono 800.626.2000.
Write down the model
and serial numbers.
You’ll find them on a label on
the lower left side near the front.
These numbers are also on the
Consumer Product Ownership
Registration Card that came with
your washer. Before sending in
this card, please write these
numbers here:
Model Number
Serial Number
Use these numbers in any
correspondence or service
calls concerning your washer.
WARNING: For your safety the information in this manu~ must be fo~owed to minimim
the risk of fire or explosion or to prevent property damage, personal injury or loss of life.
—Do not store or use gasoline or other
● Immediately cd your gas supplier from a
flammable vapors and liquids in the
neighbor’s phone. Fotiow the gas suppfier’s
vicinity of M or any other app~nce.
instructions.
—-T TO DO ~ YOU SWLL GAS
● If you cannot reach your gas supplier,
. Do not try to tight any apptiance. ca~
the tire department.
● Do not touch any electrid switch;
—hstilation and service must be performed
do not use any phone
in your btiding.
by a qualified instiler, service agency or
the gas supplier.
s Clear the room, building or area of au
occupants*
All washing instruction terms in this book conform to the Care
Labeling Rule established by the Federal Trade Commission, January 1984.
If You Need Service
To obtain service, see the Consumer Services page NEXT, if you are still not pleased, write all the
in the back of this book.
details—including your phone number—to:
We’re proud of our service and want you to be
Manager, Consumer Relations
pleased. If for some reason you are not happy with the GE Appliances, Appliance Park
service you receive, here are three steps to follow for
Louisville, KY 40225
further help. FINALLY, if your problem is still not resolved, write:
FIRST, contact the people who serviced your Major Appliance Consumer Action Panel
appliance. Explain why you are not pleased.
In
20 North Wacker Drive
most cases, this will solve the problem. Chicago, IL 60606
2

A
WARNING-To reduce the risk
of fire, electric shock, or injury to
persons when using your apptiance,
follow basic precautions, including the following:
. Use this appliance only for its intended purpose
as described in this Use and Care Book.
o
$,
● This washer must be properly
‘Q_\+i $
=*$
installed and located in accordance
with the Installation Instructions
before it is used.
If you did not receive an
Installation Instructions sheet with your
washer, you can obtain one by calling, toll
free, the GE Answer Center! 8W.626.2~.
—Properly ground to conform with all
governing codes and ordinances. Follow
details in Installation Instructions.
—Install or store where it will not be exposed
to temperatures below freezing or exposed
to the weather.
<onnect to a properly rated, protected and sized
power supply circuit to avoid electrical overload.
<onnect to adequate plumbing and drain
facilities as described in the Installation
Instructions.
● Turn off water faucets when the washer is not in
use to relieve pressure on hoses and valves, and
to minimize leakage if a hose or valve should
break or rupture.
w
● When disconnecting this appliance
~ pull by the plug rather than the cord to
avoid damage to the cord or junction of
cord and plug. Make sure that the cord
is located so that it will not be stepped on, tripped
over or otherwise subjected to damage or stress.
&
● Do not repair or replace any part
of the appliance or attempt any
servicing unless specifically
recommended in this Use and Care Book or
in published user-repair instructions that you
understand and have the skills to carry out.
To minimize the possibility of injury:
d
● Do not mix chlorine bleach with
ammonia or acids such as vinegar andor
rust remover. Mixing can produce a
mcv
toxic gas which may cause deati.
4 ‘~
h
● Do not wash or dry articles that
have been cleaned in, washed in,
~ / soaked in, orspotted with
combustible or explosive substances
(such as wax, paint, gasoline, degreasers, dry-
cleaning solvents, kerosene, etc.) which may
ignite or explode. Do not add these substances
to the wash water. Do not use these substances
around your washer antior dryer during
operation.
A
WARNING—HYDROGEN GAS
is produced by the chemical action
within your water heater and the gas
can accumulate in the water heater andor water
pipes if hot water has not been used for a period
of two weeks or longer. HYDROGEN GAS
CAN BE EXPLOSIVE UNDER THESE
CIRCUMSTANCES. So to prevent the
possibility of damage or injury, if you have not
used hot water for two weeks or more, or move
into a residence in which the hot water system
may not have been used for some time, turn on
al} hot water faucets and allow them to run for
several minutes before using any electrical
appliance which is connected to the hot water
system. This will allow any hydrogen gas to
escape. Since the gas is flammable, do not
smoke or use an open flame or appliance
during this process.
● Never reach into washer while it is
moving. Before loading, unloading
or adding clothes, push in the Cycle
Selector knob to OFF position, then
wait until the machine has completely stopped
before opening the lid.
● Close supervision is necessary if
this appliance is used by or near
children. Do not allow children
to play inside, on, or with this
appliance or any discarded
appliance.
Di;pose of discarded appliances and
shipping or packing materials properly. Before
discarding a washer, or removing from service,
remove the washer lid.
(continued next page)
3

WORTANT SAFEW ~STRUCmONS
(continued)
m
● Keep all laundry aids (such as
detergents, bleaches, fabric softeners,
‘ etc.) out of the reach of children,
m
preferably in a locked cabinet,
Observe all warnings on container
labels to avoid personal injury.
&
. Keep the area around and underneath
your appliances free from the
accumulation of combustible materials,
‘. -such as lint, paper, rags, chemicals, etc.
Q Keep the floor around your appliances clean and
dry to reduce the possibility of slipping.
s To minimize the possibility of electric
shock, unplug this appliance from the
power supply before attempting any
maintenance or cleaning (except the
removal and cleaning of the lint filter).
*
NOTE: Turning the Cycle Selector
~ knob to an 0~ position does NOT
disconnect the appliance from the
power supply.
● Do not tamper Mth controls.
s Do not operate this appliance if it is damaged,
malfunctioning, partially disassembled, or has
missing or broken parts, including a damaged
cord or plug.
● Never climb on or stand on the washer top.
● Do not wash fiberglass articles in your washer.
Skin irritation could result from the remaining
particles that may be picked up by clothing
during subsequent washer use.
● The laundry process can reduce
h
I 4 ‘\ the flarneretardancy of fabrics.
IT o avoid such a result, the garment
manufacturer’s care instructions
should be followed very carefully.
For washer operation
● Do not leave washer lid up during cycle.
This will stop the wash and spin action and
prevent completion of the cycle.
SAVE T~SE
~STRUCTIONS
4

Regular Cycles—
Permanent Press Cycles—
For most cottons, linens, work and play clothes. For loads of synthetics, blends
andor delicate fabrics.
Longer wash times plus deep rinse, spray rinse and A
cold water cool down helps prevent set-in wrinkles
spin provide thorough washing and detergent removal. in permanent press shirts, blouses, dresses and similar
apparel with normal soil.
Handwash System— Spotscrubber
System—
Saves time and energy when washing small loads The Spotscrubber cycle uses a special wash cycle and
of lightly soiled clothes. A special agitator concealed
a highly concentrated detergent solution in a small
under the regular agitator washes small and delicate amount of water in the Mini-Basket tub.
loads gently but effectively. The Handwash System Rinse water carries away soils and detergent suds and
uses up to
24Y0 less water than the regular low water
level selection.
automatic extra rinse assures complete removal of
detergent.
Optional Extra Rinse Cycle—
PreWash Cycle—
The option of an extra rinse helps assure complete For use when clothes are excessively soiled.
bleach and detergent removal when extra detergent Provides an agitated soak, and a soak without
was used or where unusual skin sensitivity to
agitation, followed by agitation and spin. Washer
detergent is a concern.
must be reset for desired wash cycle.
Knits Cycle—
Extra Cleaning Cycle—
A shorter cycle specially-designed for today’s knits.
For modern fabrics with heavy or oily soil. Agitation
An early and long spray rinse cools down fabrics for a longer time loosens stubborn soils.
before the washer reaches maximum spin speed to
help prevent wrinkle setting.
Soak Cycle—
Auto Soak Cycle—
Clothes activate in a soaking agent for a short time, This will add additional wash time on cycles to allow
then the water spins out. Washer turns off at end of the detergent to break down excessive soils. After the
Soak Cycle—must be reset for desired wash cycle. Auto Soak is complete, it will automatically move
through the selected cycle.
Delicate Cycle— Washable Woolens Cycle—
For lingerie and fabrics requiring special care, this This cycle
helps to reduce the need to wash these
cycle has a gentle wash and a slow spin.
fabrics by hand.
Washable Silks Cycl*
Mini-Basket System—
For fine washable silks. Check manufacturers’ care Uses the Mini-Basket feature. Provides a complete
labels for special instructions.
wash, rinse and spin cycle.
5

HOW TO OPERATE YOUR CLOTHES WASHER
Features and appearances may vary slightly
WARNING—To reduce the risk of fire, electric shock, or injury to persons when using your
appliance, read the IMPORTANT SAFETY INSTRUCTIONS before operating this appliance.
Em
uRGE ~E~E,
.- D-*
UROE./
t\
T
@
MEO*
\. 4
~m
Mno
WASH
SMLL
load Size
Programmed Twelve Cvcle Washer with HandWash
e
Setting the Controls
Use the Suggested Fabric and Cycle Settings
guide to help you make the proper selections.
~Select an automatic Fabric Care Program
OR customize a Fabric Care Program
● To use the automatic Fabric Care Programs, select
one of the following.
Choose desired For these Set Matching
For these
Fahric Care Was~inse
Cycle Selection WasMSpin
Selection Temperatures (On Dial) Speeds
Cottons Colofiast
HoVCold
Cottons, Regular Normal/Fast
Cottons Non-Colotiast
Cold/Cold Cottons. Reeular NormalEast
Permanent Press-Knits *WardCold
Permanent Press Normal/Slow
& Knits
1
I
Delicates-Wmh. Silk Cold/Cold Delicates Gentle/Slow
1
Washahle Woolens
*Warm~arm Delicates Gentle/Slow
*GGW(,rrrl W,aI’,r i,$ Op[)ro.ritn(t(el). YOOE to IIO”E (hc~nd cornfc]riuble).
● To customize a Fabric Care Program.
The automatic Fabric Care Program is programmed
for the majority of laundry you will wash. Customizing
your washer to your specific needs is easy.
For example: You want to wash a load of clothes at
warm wash, cold rinse, normal wash speed and fast spin
speed. To do that simply press Permanent Press-Knits
pad (for the warm wash and cold rinse) and set the
Cycle Selector knob at
Normal on the Cottons, Regular
cycle (for Normal Wash Speed and Fast Spin Speed).
Conons,
o“-
EnMm.’,
Regular
JF
PERMMESS
( TF ‘KNms ‘em”nentp’ess ‘ ,.
‘x”ac’e*ning7fi%-T’
—
I
..--., -“., --.. ---.
=--”r--.., —
~ Select Water Level.
SMALL: Washer is less than 1/3 full of clothes.
MEDIUM: Between 1/3 and 1/2 full.
LARGE: Between 1/2 and 2/3 full.
EXTRA LARGE: Over 2/3 full.
HANDWASH: Not used for regular loads. See How to
Use the Handwash System section.
If you wish to increase the water level after you’ve made
a selection, turn knob to reset and select new level.
Select Cold Wash if desired, this option
will cancel the wash temp. in the Fabric Care
Selections.
Select Extra Rinse, if desired. Pressing pad will
provide a second deep rinse with
Spotscrubber,
Cottons and Regular, or Permanent Press and
Knits cycles. Press the Reset pad to cancel
selection.
@ End Cycle Signal. Select this signal to remind
you to remove clothes from the washer when the
cycle ends. Signal will sound and then stop.
~ The Reset Options pad will allow you to cancel
a selected Option.
~ Push Cycle Selector knob in and turn clockwise to
your selected wash setting.
@ Pull Cycle Selector knob
@ START
out to start the washer. If
you wish to change setting
after washer has started, push
P
. \ ‘
STOP @
Cycle Selector knob into stop
the washer and reset to the new
position. Setting can be changed at any time.
6

Sorting and Loading
● Sort clothes carefully by fabric type, weight, color
● See Bleach and Fabric Softener Dispenser sections
and amount of soil, according to instructions in How for instructions in their uses.
to Sort Clothes section.
● For information on how to use bleaches and fabric
● Add measured amount of detergent. See Detergents
softeners, see Other Laundry Products section.
section for information on detergents and other
laundry additives.
● Close the lid. Washer will fill but not agitate or spin
with the lid open.
● Load clothes into wash basket, being careful not
to overload. See How to Load Your Washer section.
Cycle Times —
Total Cycle Times (Approximate Minutes)
NOTES:
● Total time includes pauses between each phase of the cycle.
● Total time does not include water fill times. Fill times vary
depending on household water pressure and your selected water level.
Perm Press & Knits Delicates PreWash
Extra Cleaning and Cotton Regular
I I
20
10
I
9*
I
34
I
* Total Cycle Minutes do not include the auto soak cycle you have chosen.
Optional Extra Rinse cycles are approximately 15 minutes.
End Cycle Signal (operates with any cycle.)
The signal will sound just before the end of the cycle To stop the signal while sounding, press the Reset
to remind you to remove the clothes to avoid excess Options pad or advance the Cycle Selector to OFF.
wrinkling before drying.
How to Use the Bleach Dispenser
Use this dispenser with
liquid bleach only.
If you prefer to
/
● Measure bleach carefully.
See manufacturer’s instructions.
use powdered
● Pour measured amount of liquid bleach directly
d.-
bleach, pour it
into the wash
basket along with
your detergent. Do
%%
into bleach dispenser.
● Do not ovetilll or allow dispenser to overflow.
Avoid splashing. Undiluted bleach can cause
fabric damage.
hot pour p;wdered bleach ● Never pour undiluted
liquid bleach directly
into the bleach dispenser.
onto clothes or into the wash basket.
(Cc]ntinued next page)
7

OPERAT~G mSTRUCTIONS
(continued)
How to Use the Fabric Softener Dispenser
● Position the Fabric Softener ● Do not stop the washer during the first spin.
Dispenser on the agitator.
. Pour manufacturer’s
recommended amount
of fabric softener into
a one cup (240 ml)
measuring cup.
\&
This will cause the dispenser to empty too soon.
d.
● Do not use the Fabric Softener Dispenser with
the Soak or PreWash cycle.
Q
● If the dispenser gets clogged, soak it in a
solution of one cup (240 ml) water and one
cup (240 ml) alcohol.
● Add enough water to fill
the cup 1/2 full.
● Pour the diluted softener into the dispenser.
● The fabric softener will automatically be dispensed
at the proper time.
How to Use the Auto Soak Cycle
In the Auto Soak cycle the washer fills, agitates and ● PreWash with Auto Soak: Set the Cycle Selector
soaks for the time you selected. It automatically knob for soak time desired in the PreWash cycle.
advances into the next cycle. Start the washer. The washer will agitate, soak and
automatically advance into PreWash.
ENERGY-SAVING T~S
If your clothes and household items don’t look clean
and fresh after washing, you will probably rewash
them.. and that means you’ll waste energy.
Remember to sort your clothes carefully, and load
them properly, select correct cycles, use enough
detergent and choose a water temperature warm
enough to release and get rid of soil.
● Try to wash less often. Save articles of the same
type of fabric until you have a full load.
● If you must wash smaller loads, adjust the amount
of water. Small loads should have lower water levels.
● Always rinse in cold water. The temperature
of the rinse does not affect cleaning.
● Wash in off-peak utility hours. Your local utility
can tell you which are the off-peak hours.
● Use your washer’s Normal Spin. This will remove
more water during spin, which will shorten drying
cycle to save more energy.
8

Cycle Suggested
Permanent Press & Knits
Delicates
Regular
Extra Cleaning & Auto Soak
Special Instructions
*Down-filled garments
**Pillows
***Blankets
For Clothes Loa~abrics such as:
● Synthetics
● Permanent press, treated cottons,
blends with cottons
● Down-filled garments, if machine
washing is recommended*
● Pillows**
● Baby clothes (delicate)
c Lingerie
● Cottons and linens
● Denims
● Blankets***
● Baby clothes (sturdy)
● Work clothes with heavy soil
WasMSpin Speed
NormaVSlow
Gentle/Slow
Gentle/Slow
Normal/Fast
Normal/Fast
Wash frequently to fluff up the down and retain the garment’s warmth.
WASH SEPARATELY. Wet down gives off an odor which may be absorbed
by other garments. Odor disappears when garment is dry. Treat heavily soiled
areas with liquid detergent or a paste made of water and powdered detergent.
Close zippers. Wash 2 or 3 garments at a time or add towels to balance.
GARMENT MUST BE TUMBLE DRIED.
Pillows are made of different materials—dacron, foam, polyester, natural feather,
and down. MANUFACTURER’ S CARE LABELS MUST BE FOLLOWED
CAREFULLY. If washing is recommended, check pillows for weak seams or
holes and mend, to prevent escape of the filling. Fill washer, add detergent
and agitate for several minutes. Add two pillows at a time to balance load.
Use largest water level.
Fill washer with water; add detergent and allow to dissolve. Add blanket.
WASH ONLY ONE BLANKET AT A TIME. On electric blanket, sew a strong
piece of cloth over plug to protect blanket and washer from damage. Pretreat
heavily soiled spots with
liquid detergent.
9

HOW TO USE THE HA~WASH SYSTEM
~pical HANDWASH System Wash Loads
● Small loads of regular fabrics ● Delicate loads such as lingerie, panty hose, girdles,
(up to 2 pounds) (.9 kg). blouses, sweaters, socks, shirts, baby clothes and
other small, delicate
hand-washables.
How to Wash a Small Load of Regular Fabrics or Delicate Hand-Washables
● Remove HEAVY
DUTY agitator as
follows:
—Push switches to
UNLOCK.
—Lift out HEAVY
DUTY agitator
leaving smaller
HANDWASH agitator in place.
● Put measured detergent in the wash basket. See
detergent manufacturer’s instructions.
● Load clothes in the wash basket.
● See How to Use Bleach and Fabric Softener
Dispenser sections.
● Close lid and set controls as follows:
—Set Water Level to HANDWASH position.
—Select desired
WasMSpin speed and Wash/Rinse
temperature or your Fabric Care Selection
according to the fabrics you are washing.
—Push the Cycle Selector knob in and turn to the
desired setting.
● When washing stockings, panty hose and other
easily tangled items, always handle separately. To
minimize tangling, we recommend the use of a net
laundry bag.
● To replace the HEAVY DUTY agitator:
—Position outer agitator over HANDWASH agitator
and rotate until agitator falls easily into place. DO
NOT FORCE.
—Press gently on HEAVY DUTY agitator until
it is seated securely.
—Push switches to lock HEAVY DUTY agitator
in place.
BE SURE HEAVY DUTY AGITATOR IS
SECURELY IN PLACE BEFORE WASHING
REGULAR LOADS OF CLOTHES.
NOTE: HANDWASH agitator cannot be removed.
—Pull out Cycle Selector knob to start washer.
10

Sort by Surface Texture
Separate
(
m
m
Lint a
%wProducers
from
LA
me
.
~
Lint u
%~Collectors
LJ
LINT PRODUCERS—such as terry toweling and
chenille—give up lint.
LINT COLLECTORS—such as man-made fibers and
napped fabrics like velveteen and corduroy—attract
lint. These must be washed separately.
For more information on lint control, see The
Problem Solver section.
Sort by Fabric
‘eparate mfro’efromBfro’m
In addition to sorting to
reduce lint collection,
it is recommended
that fabrics of similar
construction be
washed together
whenever possible.
Sort by Color
Separate
For instructions
on different fabrics
and loads, see the
Fabric and Cycle
Settings guide.
It pays to check and prepare
clothes for washing.
● Empty pockets, brush out cuffs,
zip zippers, and fasten snaps,
hooks and buttons.
● Do any necessary mending—rips,
hems, tears.
● Check all items for areas of heavy
soil or stain.
● Remove stains. See Stain
Removal Guide.
● Turn poly knits inside-out to
minimize fabric surface damage.
EXTRA CLEANING
(See Tips to Help You Select
Settings section for instructions.)
See Stain Removal Guide.
See Fabric and Cycle
Settings guide.
See The Problem Solver section.
Soaking and Pretreating-a good
way to loosen deep soils and stains.
A thorough soaking with detergent
or special soaking agent is another
way to remove heavy
soils,
embedded dirt and even some stains.
Soaking can be either a completely
separate washing step or a
preliminary step to a complete wash
cycle. For detailed information on
how to soak in your washer, see
How to Use the Soak Cycle.
FOR INFOWATION ON
SOAKING AGENTS, see Other
Laundry Products Guide.
● Pretreat heavy soil by rubbing
in a small amount of liquid
detergent or a paste made of water
and powdered detergent or soap.
For best results, wait 1/2 hour
before washing.

HOW TO LOAD YOUR WAS~R
This illustration, with clothes just
reaching the Clothes Retaining
Ring, shows a proper load. Clothes
have ample room to move because
they are not packed down, nor
wrapped around the agitator.
Clothes are loaded dry since wet
items are likely to pack down
which encourages overloading.
This size load requires a full
water fill.
What is the best size load of
clothes—large, medium, or
small? Save time, energy and
detergent by avoiding extra use of
the washer. Try to wash a full load
of clothes. If you can it is better to
save clothes until you have a full
load. If you must wash smaller
loads, save water, energy and
detergent by adjusting the water
level for the size of the load. See
Operating Instructions.
● Load clothes dry.
● Take a properly sorted group of
clothes and drop them loosely in
the wash basket in this order:
~ Large items–like sheets. Do
not wrap around the agitator.
~ Small items–like
washcloths.
~ Medium size items–like
towels.
DO NOT OVERLOAD YOUR
WASHER.
● Try to mix large and small items
in each machine load for better
washing action.
s Wash large items (blankets, bed
spreads, mattress pads, etc.)
separately.
● If machine is overloaded, you
may experience
oversudsing or
out of balance conditions.
To Add Items After the Washer Has Started
● Turn off the washer by pushing in the Cycle NOTE: When washing stockings, panty hose and
Selector knob. other easily tangled items, always handle separately.
● Add any additional articles by submerging them next To minimize tangling, we recommend the use of a net
to the agitator. laundry bag.
Special Recommendations for Washing Permanent Press If You Do Not Have a Dryer
If you are machine-washing permanent press clothes ● Be careful not to overload washer. Permanent press
that you plan to line dry or drip-dry, use extra care to clothes must have ample room to move freely. A
minimize wrinkling in the wash process: medium size permanent press load is the largest
● Remove clothes promptly as soon as washer stops
that should be washed.
and hang immediately.
“ If you can select a water level, use more water than
you would for a regular load. Use a medium water
level for a small load. Use an extra large water
level
for a medium load.
12

The use of a sufficient amount of detergent is one of the most
important things you can do to make sure your wash comes out clean.
Always follow the detergent manufacturer’s recommended amount.
Amount required varies
according to:
1.
Water hardness
2. Amount of soil
3. Size of load
4. Type of detergent
5. Wash temperature
Use more detergent if
you have...
1. Hard water
2. Large loads
3. Greasy or oily soils
4. Lower wash temperature
5. Low phosphate detergent
If the recommended amount of How to use detergent—
detergent produces too many suds,
granular, powdered or liquid:
switch to a lower sudsing detergent
brand, and follow instructions For best results, add detergent to
the wash basket before loading
on package.
clothes. If you load your clothes
Using too little
detergent is a
common cause
of laundry
e
first, add detergent next to the
agitator.
-
=
problems. Always ~
measure detergent —
in a standard measuring cup.
~RD WATER—DO YOU WW IT?
Before you can decide what to do about hard
water, you need to know if you have it and, if so,
how hard it is.
“ If you live in a municipal area, contact your
water company.
s If you live in a rural area, or in some suburban areas,
contact your county agent.
The answer will be “you have ‘so many grains’ per
gallon (3.8 liters).” This means:
O to 3.5 grains per gallon (3.8 liters)—SOFT
3.6 to 7 grains—HARD
7.1 to 10.5 grains—VERY HARD
10.6 grains and over—EXTREMELY HARD
If your water is SOFT, you have no problem. You
can use soap or detergent as you prefer and forget all
about hard water. If you have HARD water—less than
10 grains—and you use phosphate detergent, you also
have no problem.
But, if you have more than 10 grains, you will need
to soften your water with either...
1. An installed water softener in your home, or
2. The use of a packaged water softener.
For information on water softeners, see the
manufacturer’s recommendations.
13

OT~R LA~RY PRODUCTS
Laundry
Product and
~pe
BLEACH
Chlorine liquid
such as Clorox brand
Non-chlorine such as
Clorox 2 brand
FABRIC SOFTENERS
Rinse additive such as
Downy brand
SANITIZER
Chlorine bleach
such as
Clorox brand
WATER SOFTENER
Non-precipitating
such as
Calgon brand
Precipitating such as
Borax brand
SOAK AGENT
Such as
Biz brand
PRE-TREATING, STAIN
AND SPOT REMOVERS
Such as
Spray’n Wash
and
K2R brands
TINTS AND DYES
Powdered such as
Rit
and Tintex brands
How to Use It
Use your bleach dispenser.
See How to Use Your Bleach
Dispenser section.
If you do not have a bleach dispenser,
pour diluted bleach next to the agitator.
Follow package directions.
Put bleach into washer with detergent.
Follow package directions
for diluting softeners.
Use in case of infection
and contagious disease.
See under Bleach above.
Follow package directions.
Add at start of wash cycle.
Follow package directions.
Add at start of wash cycle.
Follow package directions,
Follow package directions. Treat only
heavily soiled areas. Check garments’
care labels for instructions.
Follow package directions.
NOTE: Tinted garments may
not be colorfast, Wash separately.
Special Instructions
1) Dilute bleach before using on any fabric. Do not pour
undiluted liquid chlorine bleach directly into washer
or on dry clothes.
2) Some of today’s washable fabrics should not be chlorine
bleached such as: silk, wool,
spandex, or non-fast colors.
3) Check manufacturers’ care labels for special instructions.
1) Maybe used on most fabrics. Test fabric first.
1) Helps make clothes fluffy and soft.
2) Reduces static electricity.
3) Use the following manufacturer’s direction. Too much
may cause a hard, rough feeling on some clothes.
4) Do not pour directly on clothes.
Guards against infection by killing most bacteria and viruses.
Suspends hardness minerals in solution, keeping
water clear.
Combines with water hardness minerals to form precipitate
which gives cloudy or milky appearance to water.
For best results, soak garments a minimum of 30 minutes.
CAUTION: Washer and dryer control panels and finishes may
be damaged by some laundry pretreatment soil and stain
remover products if such products are sprayed on or have
direct contact with the washer.
Apply these pretreatment
products away from washer. The fabric may then be washed
normally. Damage to your washer caused by pretreatment
products is not covered by your warranty.
Clean washer to avoid discoloration of next load. Go
through complete cycle using hot water, 1/2 cup (120 ml)
detergent,
I cup (240 ml) bleach. Wipe exterior parts.
CAUTION: Tinting may discolor plastic in washer.
Subsequent washings will reduce discoloration but may never
eliminate it.
14

1. Try to remove stains as soon as possible.
● Test stain removal product on a hidden
The fresher the stain, the easier it is to remove. inside seam or on a sample of the material.
2. Before attempting to remove any stain, take ● Avoid use of hot water on unknown stains.
these steps: It can set some stains.
● Find the fabric in the chart on the next page, 3. Follow stain removal with a thorough rinsing.
and use only recommended methods. 4. Wash with recommended amount of soap
● Check the care label instructions that came with
or detergent.
the garment.
Stiin Removal Hint—Using Chlorine Bleach for White and Bleachable Fabrics
Mix 1/4 cup (60 ml) chlorine bleach with one gallon (3.8 liters) of cool
water—approximately 80°F. (27°C.)—in a sink or pan. Soak stained area
for 5 minutes and launder in washer.
The Case of the “Invisible” Stiin
Food or cooking oils on your synthetic garments If these stains are not completely removed in the wash,
may cause stains which are virtually invisible and the oily spots may pick up dirt from the wash water,
which you may not notice as you put your clothes Then they
will become very visible and you may think
into the washer. they were caused by the wash cycle itself.
Once These Spok Become Visible, How Can You Remove Them?
● Rub in undiluted liquid detergent and let stand 30 minutes.
● Rewash using hottest water the fabric can stand.
How Can You Prevent These “After-You-Wash” Shins?
● Increase the amount of detergent normally used.
● Increase water temperature where fabric will permit.
● Wash synthetic garments more often.
15

STAIN ~MOVAL GU~E
Stain
White and Bleachable Fabrics
See Controls Setting Guide. Other Washable Fabrics
Adhesives
(Chewing Gum, etc.) Rub with ice or immerse in very cold water. Use
du/1 to[~l to
carefilly scrape off as much adhesive or gum as possible. Sponge
with a safe dry cleaning fluid, *rinse well, then wash as usual.
Same as white and bleachable fabrics
Antiperspirants,
Deodorants
Apply undiluted liquid detergent. Rinse. If stain remains, bleach
according to the Stain Removal Hint; launder. If color has changed,
you may be able to restore it by sponging with ammonia.**
Rinse thoroughly,
Same as white and bleachable fabrics
except use non-chlorine bleach.
Blood Soak in cold water, then launder in warm water. If stain remains,
bleach according to the Stain Removal Hint; launder.
Soak in cold water. Treat stain with a safe dry cleaning fluid,*
rinse well, then wash as usual. Bleach according to the Stain
Removal Hint.
Sponge or soak in cool water, then
launder.
Chocolate, Cream,
Ice Cream and
Milk
Soak in cold water. Sponge with a safe
cleaning fluid, * rinse well, then wash
as usual.
Coffee and Tea
Without cream: Bleach according to the Stain Removal Hint;
launder. With cream: Follow guide directions for cream.
Sponge with warm water. If stain remains,
apply warm glycerine, let stand 30
minutes and rinse well, or sponge with
a safe dry cleaning fluid, * rinse well,
then wash as usual.
Treat stain with safe dry cleaning fluid,* rinse well, then wash
as usual. Bleach according to the Stain Removal Hint. Sponge with a safe dry cleaning
tluid,*
rinse well, then wash as usual.
Cosmetics: Eye Shadow,
Lipstick, Mascara, Liquid
or Pancake Makeup, Rouge,
Powder; Crayon; Grease,
Oil, Tar, Cod Liver Oil
Sponge with warm water. Bleach remaining
stain with non-chlorine bleach.
Sponge with warm water. Apply
undiluted
/iquid detergent. Bleach remaining stain
with non-chlorine bleach, then launder.
Old mildew stains can seldom be
removed. Scorch can seldom
be removed.
Fresh Fruit, Fruit Juices,
Wine, Vegetables or Food
Coloring
Soak stain in cool water. If stain remains, bleach according to
the Stain Removal Hint; launder.
Grass, Foliage, Flowers,
Mildew,Scorch Apply undiluted liquid detergent. Launder. (Treat mildew spots
while they are fresh, before mold has a chance to weaken fabric.)
If either type stain remains, bleach according to the Stain Removal
Hint; launder. (Severe scorch cannot be removed.)
Ink, Ballpoint
Fresh stains: Place stain face down on an absorbent towel and
use a spray cleaner or sponge with dry cleaning fluid, * rinse well,
then wash as usual. Old stains: Bleach according to the Stain
Removal Hint; launder.
Same as white and bleachable fabrics
except launder using non-chlorine bleach.
Perspiration
Apply undiluted liquid detergent and launder in warm water.
If color has changed you maybe able to restore it by treating
with ammonia or vinegar.** If any stain remains, treat with safe
dry cleaning fluid,* rinse well, then wash as usual.
Launder in warm water. Rinse well. Bleach
with non-chlorine bleach.
Apply rust remover,** using manufacturer’s directions. Rinse
and launder.
Same as white and bleachable fabrics
Rust
A
*CAUTION: Because cleaning fluids tend to be toxic, k sure
**DO not mix ~hl”rine bleach with ammonia or acids such dS
you are in a well ventilated mom when using them. No
vinegar and/or rust remover. Mixing can produce a toxic gas
cleanine fluid should be used unless user is familiar with the
which may cause death.
limitations and
r;quired cautions (usually printed on label). Use extreme
caution with flammable compounds. Save and refer to garment manufacturer’s care labels.
Under no circumstances should fabrics containing flammable materials
(waxes, cleaning fluids, etc.) be washed in washer.
16

PROBLEM
LINT OR RESIDUE
ON CLOTHES
GREASY OR OILY
STAINS ON
LAUNDERED
GARMENTS
GRAYED CLO~S
QUESTIONS?
USE THIS PROBLEM SOLVER
POSSIBLE CAUSE
● Incorrect sorting of clothes. Separate lint producers (such as terry towels and
chenille) from lint receivers (such as man-made fabrics, velveteen, corduroy).
● Washing too long, especially for smaller loads. For normal soil, wash one minute
per pound of dry clothes.
● Use of non-phosphate detergents which combine with hardness minerals to form a
precipitate which can be mistaken for lint. Use a phosphate or liquid detergent; use
warmer wash water or soften water with an installed mechanical softener or a
packagd water softener.
● Powdery residue from granular detergent may appear to be lint. Predissolve granular
detergent in hot water before adding to washer; make sure detergent is completely
dissolved before adding clothes; switch to liquid or cold water detergent or use
warmer wash water. See Detergent section.
● Overloading will cause abrasion which creates excessive lint. Wash fewer items
with correct water level.
● Too much bleach. Use correct amount of bleach according to package directions.
● Not enough detergent to hold lint in suspension during wash cycle. Increase amount
of detergent. See Detergent section.
● Incorrect use of fabric softener. If used in wash cycle, softeners may react with
detergent to create a white deposit. Use softeners in rinse cycle only unless package
specifies adding to wash cycle. See Other Laundry Products section.
● Pilling usually on polyester-cotton blends is caused by normal wear and may look
like lint.
~rning clothes inside-out may provide some help.
● Static electricity caused by overdying will cause attraction. Use fabric softener in
rinse cycle.
These are sometimes called “Invisible Stains” because you may not notice them before
washing clothes. However, if oily soils are not completely removed in wash cycle,
the oily spots may pick up dirt from the wash water. The spots will then be very visible.
They are
not caused by the washer. Wash synthetic garments as soon as possible after
wearing. Use more detergent than normal and hottest water fabric can stand. If spots
appear, rub in undiluted liquid detergent, let stand 30 minutes and rewash with extra
detergent using hottest water fabric can stand.
● Insufficient detergent. You may need to increase amount of detergent used if load is
larger than
norrnd, if soils are oily or heavier than average, if water level is large or if
water is Hard to Extremely Hard.
● Water not hot enough for type of load. Be sure water heater is set to deliver hot water to
the washer at 120°F.-1500F. (45°C.+50C.). Do not wash when other hot water needs—
such as dishwashing or family baths-are heavy.
● Poor or inferior detergent. Change to phosphate detergent, if possible. Follow these steps:
1. Use water conditioner (such as Calgon brand).
2. Pretreat stains,
3. Use the hottest water possible.
4. Use bleach where possible.
5. Use preso~ aids.
6.
Instil water softener.
● Washer overloaded. Clothes cannot move freely to loosen and remove soil, causing
gray appearance. Follow correct loading procedures for size of load.
(cc~ntinued next page)
17

T~ PROBLEM SOLmR
(continued)
PROBLEM
GRAYED CLOTHES
(continued)
YELLO~D
CLOTHES ‘
BLUE OR GRAY
COLOR STAINS
SHRW~GE,
GENERM
POSSIBLE CAUSE
● bproper soaking with insufficient detergent. Usually a 30-minute soak is sufficient.
However, when using extended soaks for heavily soiled garments, you may need to use
twice the recommended amount of detergent.
● Use of soap in hard water. Switch to a phosphate detergent, or follow six steps at
bottom of opposite page.
● Washing too long may result in increased soil deposition, Use shorter wash times for
smaller loads.
* Detergent dissolves too slowly. Detergent must be present in the wash solution at the
start of agitation.
See Detergent and Additives section.
● To restore grayed clothes, follow one of these procedures:
1. ~t clothes in washer, Fill with HOT water. Check garment manufacturer’s care
labels to determine if hot water is suitable for garment.
● Add a non-precipitating type of water softener such as Cdgon brand.
Use 2M times as much as you need for normal water softening.
. Do not use detergent or soap.
● Allow clothes to go through complete cycle.
● Repeat, if necessary.
2. If you prefer to use the Soak cycle, see How to Use the Soak Cycle section. Use
the water softener
in place of soak agent or prewash detergent and allow clothes
to soak for about 20 minutes.
3. Use an extra cleaning cycle, see Tips to Help You Select Settings section.
● Incomplete removal of soil due to constant use of insufficient detergent. Check hem
of T-shirt or pillow case. If they are white and center is yellow, it contains body oil.
Restore whiteness following procedures in Grayed Clothes, above.
Q Chlorine bleach may yellow some fabrics with resin finishes. Use oxygen bleach (such
as Clorox 2 brand). Refer to garment manufacturer’s care instructions. Restore color
using color remover (such as
Rit or Tintex brands), following package directions.
● kn or manganese in water may cause overall yellowing or yellow spots.
1.
2.
3.
4.
Use extra detergent plus anon-precipitating water softener dissolved in water before
adding clothes. Use non-chlorine bleach.
Have a special filter installed in your home to remove iron and manganese
from water.
Run hot water for a few minutes to clean iron residue buildup in lines; drain water
heater occasionally.
To remove spots: Spread stained portion over pan of boiling water and squeeze
lemon juice through stain. To remove overali yellow, use a commercially available
rust scale remover, following package instructions. If porcelain damage can occur,
do not use in the washer; use a plastic container,
hproper use of fabric softener. Never pour fabric softener directly on clothes; always
dilute before adding to rinse water. See Other Laundry Products section. Also, do not
lift lid during spin. This may cause improper dispensing, resulting in stains.
To remove
shins: Dampen stained area and rub with undiluted liquid detergent. Rewash, using
chlorine bleach if safe for fabric.
Some fabrics will shrink whether washed in a washer or by hand; others maybe safely
washed but will shrink in a dryer. Follow garment manufacturer’s care instructions
exactly. If in doubt, do not machine wash or dry.
18

PROBLEM
SHRINWGE,
~ITS
WRIN~ING N
PERMANENT P~SS
AND “NO-IRON”
ITEMS
SNAGS, HOLES,
TEARS, RIPS OR
EXCESSIVE WEAR
POSSIBLE CAUSE
Q Relaxation shrinkage can occur in knit fabrics that have been improperly stretched
and elongated by the manufacturer. When this occurs, garment maybe pressed back
into shape
&er each wash and dry cycle.
● Progressive or delayed shrinkage is caused when starch or sizing (in some fabrics)
is gradually removed by laundering. This may also be noticed in older garments that
have been washed many times without previous shrinkage. Treat as for relaxation
shrinkage above.
● Shrinkage caused by overheating occurs in certain knit fabrics that have been heat-
shaped. When washing, drying or ironing temperatures exceed the temperatures used
to shape set, shrinkage may occur. This cannot be corrected, but it can be prevented
by washing in cool or warm water and drying on low or delicate heat.
c having clothes in dryer after tumbling stops. Remove and hang clothes immediately.
● Too many clothes in dryer. Dry only one washer load at a time. Do not combine loads,
● Improper loads. Avoid laundering heavy permanent press items, such as work clothes,
with lighter permanent press items such as shirts or blouses. Do not wash permanent
press items with regular laundry.
● Too many clothes in washer. Permanent press loads should always be smaller than
regular loads,.
.no more than medium loads to give clothes room to move freely.
● Incorrect wash and dry cycles. Use Permanent Press Wash cycle which provides
a
cooldown rinse to minimize wrinkling. Also use Permanent Press Dry cycle.
● Incorrect water level. Use larger water level for medium load, medium level for
small load.
Q Repeated washing in too hot water. Wash in cold or warm water with plenty of
detergent.
● Failure to use fabric softener. Proper use will minimize wrinkling.
To remove wrinkles:
● Retumble on Permanent Press setting in your dryer.
● Rerinse and dry on Permanent Press setting.
● If unsuccessful, retumble on high heat for 10 to 12 minutes and hang immediately.
● Send to dry cleaners for pressing.
● Some wrinties may remain which cannot be removed.
● Pins on garments or sharp objects left in pockets. Check to make sure dl such objects
are removed. Also check wash tub.
Snaps, hooks, sharp buttons, belt buckles, zippers. Fasten hooks, zippers and buttons.
Remove sharp buttons and belt buckles. This is especially important in washing knits
which snag easily. Turn knits inside out.
Holes with random square shapes with yellow discoloration may be caused by
improper use of chlorine bleach. Use only correct amount of bleach. See Other
Laundry Products section. Never add undiluted bleach to wash tub or allow clothes
to come into contact with undiluted bleach. Do not wipe up bleach spills with clothes.
Small, unnoticed tears may enlarge during washing process. Check garments before
washing and mend all rips and tears.
(c[]nlinued next pu,ye)
19

THE PROBLEM SOL~R
(continued)
PROBLEM
SNAGS, HOLES,
TEARS, RWS OR
EXCESSIVE
WAR
(continued)
HEAVILY SOILED
AREAS such as
collars and cuffs
WASHER WON’T
OPERATE
WATER
TEMPERATURE
IS INCORRECT
WATER WON’T
DRAIN
POSSIBLE CAUSE
@ Chemicals such as hair bleach, dye, permanent wave solutions, battery acids and
toilet bowl cleaners may cause fabric holes. Rinse all towels and other articles that
came
in contact with these chemicals before putting them in wash. Do not
contaminate clothing articles with these chemicals.
● As permanent press garments age, they may show fraying at collars and cuffs. This
is normal due to weakening of fibers by the permanent press process. It is not caused
by washer. You can slow this process by washing small permanent press loads with
a medium water level. Do not wash heavy items such as towels with permanent press.
Remove collar stays, when possible.
● May be caused by the use of Regular cycles for de~icate articles. Use Permanent
Press cycle. Refer to garment manufacturer’s care labels.
● Garments weakened by age, sun or atmosphere. This is inevitable and is not caused
by washer.
s Over loading or under loading washer for selected water level. Load washer only with
number of items that will move freely. Select correct water level.
Pretreat with liquid detergent. See Other Laundry Products section.
@@@@
● Make sure cord is plugged into outlet.
● Make sure both hot and cold faucets are turned on.
● Make sure controls are set and Cycle Selector knob is pulled out to ON position.
● Make sure lid is closed. Washer will fill but will not spin or agitate with lid open.
● Check house fuses or circuit breakers. If another appliance is sharing the electrical
outlet, remove it. Washer should have separate outlet.
s Make sure temperature selector controls are correctly set.
* Make sure hot and cold faucets are turned on and
regulated correctly.
● Make sure hoses are connected to correct faucets...
hot to hot, cold to cold.
Q Water valve screens may be stopped up. Remove inlet
o
+
$?
hoses from water valve. Clean the screens and reinstall hoses.
● Check house water heater to make sure it is delivering water at
120°F.–1500F. (45°C.–650C.).
● Make sure drain hose is not kinked.
● Top of drain outlet should be less than 8 ft. (2.4 m) above floor.
20