Gearwrench 83169 User manual

User’s Manual
42 in. 11-Drawer Industrial Rolling Cabinet
Model # 83169
1
www. .com [e-mail]1.800.561.8187

2
Safety Information
1. Do not pull this cabinet, push it when moving.
2. Use the brakes when this product is not being
moved. This prevents the product from rolling.
3.
4
5.
6.
7.
8.
. Before locking the cabinet, ensure the drawers are completely
closed in order for the lock mechanism to work properly.
Do not alter this product in any manner or it will void the
warranty.
9. Extension cord
Follow all manufacturers' Warnings and Operating
Instructions for your extension cord.
Only use a three-wire extension cord with all three prongs
intact. Never remove the round grounding prong.
Check the insulation and plugs of extension cord before
using. Do NOT use cord if it is worn or damaged.
□
□
□
□
Extension cord must be connected to a 125 Volt GFCI
protected outlet with proper ground. If GFCI outlet is not
available, use an extension cord with GFCI protection
built in.
□
□
□
Do NOT overload extension cord.
Do NOT run over extension cord.
Only use an extension cord that is rated for outdoor use.
□Do NOT connect extension cord to outlet that also sup-
plies critical safety equipment with power.
10. Electrical Shock Hazard
□ Do not plug cord into outlet with wet hands.
□ Do not use this cabinet near a bathtub, a shower, or a
swimming pool.
□ Cabinet plugs must match the outlet.
□ Never modify the plug in any way.
□ Do not use any adapter plugs with earth (grounded)
cabinet power strips.
This unit has one power supply cord. Make sure
the cord is unplugged before any servicing or cleaning.
NOTE : This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation. This
equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there
is no guarantee that interference will not occur in
a particular installation.
If this equipment does cause harmful interference to
radio or television reception, which can be determined
by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or
more of the following measures:
□Reorient or relocate the receiving antenna.
□Increase the separation between the equipment and
receiver.
□Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
□Consult the dealer or an experienced radio/TV
technician for help.
NOTE : This device complies with Part 15 of the FCC
Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful
interference, and
(2) this device must accept any interference received,
including interference that may cause undesired
operation.
Do not attach or mount this product to a vehicle or mobile
trailers. This may cause personal injury or product damage.
Mounting this product to any vehicle or mobile trailers in any
manner will void warranty.
Be careful when opening more than one drawer. The product
may become unstable and tip, which may cause personal injury
orproduct damage.
Keep the product on level surfaces. The product may become
unstable and tip if stored or moved on an unlevel surface,
which may cause personal injury or product damage.
Lock the drawers before moving this product. The drawers
could come open and make the product unstable and tip,
which may cause personal injury or product damage.
NOTE:
Specifications
Drawer load capacity 100 lbs
Bottom deep drawers load capacity 200 lbs
Heavy duty storage hook load capacity 35 lbs
Total weight capacity 2,500 lbs
www. .com [e-mail]1.800.561.8187

3
Tools Required
*14 mm wrench or socket (not included)Hex key (included)
A
AA
BBB
C
CC
E
D
Parts
F
G
H
C
J
J
I
K
L
DD
EE
Part Description Quantity Part Description Quantity
A
Side Handle
1
J
Barrel Locks and Keys
2
BCord Storage Brackets 2K Swivel Caster 2
C
Heavy Duty Hooks
5
L
Rigid Caster
2
D
Shelf
1
AA Screws M6x16mm 6
E
Shelf Clips
4
BB
Screws M4x12mm
4
FParts Tray 1
CC
Nut M8
3
G
Storage Tray
1
DD
Bolts M8x25mm
16
H
Peg Hooks
4
EE
W
ashers 19x8.5x2mm 16
I
Drawer Slides
13 pair
www. .com [e-mail]1.800.561.8187

4
Assembly
Attaching the Side Handle
□ Position the side handle (A) on the holes in the right
of cabinet.
□ Attach handle (A) with 6 screws (AA) and tighten
with supplied hex key. Be careful not to over tighten.
Note: The holes in the cabinet are tapped and do not
require nuts.
Installing the Cord Storage
Brackets
□ Attach the brackets (B) to the back of the cabinet
with two screws (BB) per bracket.
□ Orient the brackets (B) with one pointed up and
one pointed down so that the power outlet cord can be
wrapped around the brackets (B) for storage.
Installing the Heavy Duty
Storage Hooks
□ Attach the nuts (CC) onto the hook (C) and then
insert the hooks in the holes as shown.
□ Be sure the hooks (C) are pointing upwards for
installation, then hand-tighten the nuts (CC).
□ Securely tighten the nuts (CC) with a 14mm wrench
(not included). Be careful not to over tighten.
Installing the Shelf
□ Put the 4 shelf clips (E) into the slots on the interior
of the side cabinet as shown, installing two shelf clips (E)
on each side of the interior.
□ Be sure that all 4 shelf clips (E) are at the same level
before installing the shelf (D). Shelf can be installed at
desired level as long as the shelf clips are aligned
correctly.
A
AA
B
BB
D
E
Back
Side
www. .com [e-mail]1.800.561.8187

5
Operation
Fully extend the empty drawer.
□
□
elihwrevelesaelerenoehtpuhsuP pulling
down on the other release lever.
□Pull the drawer outward until it is released from
the drawer slide.
Extend the drawer slides.
□
□
Insert the brackets on each side of the drawer into
the slots in the slides, being careful that they are
properly positioned.
□Once properly inserted, completely close the drawer
to set the slides in their proper positions.
Installing Two Storage Trays
□ To install parts tray (F) and storage tray (G), insert the
hooks on the box into the desired holes on the left side
panel of the cabinet. Be sure that the selected holes are
aligned so that the box is level.
Installing Power Cord
□ Untie power cord located inside drawer.
□ Gently pull cord plug through grommet.
Removing the drawers Re-inserting the drawers
www. .com [e-mail]1.800.561.8187

6
□Periodically clean the drawer fronts, drawer trim, and other surfaces with a mild detergent and water.
□
Maintenance
□Grease the casters annually using high-quality
bearing grease.
□Lu
bearing grease.
bricate the slides semi-annually with high-quality
Warranty
Caster maintenance Drawer maintenance
mild cleaning detergent.
GearWrench® tool storage cabinets are warranted for 5 years from the date of purchase to be free of defects in material and
workmanship.
Apex warrants to each original Customer of Products sold by Apex that such Products are, at the time of delivery to the Customer,
free of material and workmanship defects, provided that no warranty is made with respect to:
(a) any Product which has been modified, disassembled and/or reassembled or altered in any way or improperly installed;
(b) any Product which has, in Apex’s judgment, been subject to negligence, misuse, abuse, accident, improper storage or damage
during shipment;
(c) any Product which has not been operated and maintained in accordance with normal practice and in conformity with
recommendations and published specifications of Apex; and
(d) any Products which have been serviced or repaired by anyone other than an Authorized Repair Center of Apex or modified by
anyone other than Apex. Normal wear and tear is also excluded.
These warranties set forth herein are the sole warranties applicable to Products and is in lieu of all other warranties, whether
express, implied or statutory. The implied warranties of merchantability and fitness for a particular purpose are specifically
excluded.
Remedies: Customer’s sole and exclusive remedy for breach of this Warranty is, at the option of Apex, repair or replacement of
the defective product.
The Apex Tool Group is not responsible for personal injury or damage resulting from improper tool usage, product modification,
abuse or usage beyond expected product life.
GEARWRENCH® is a registered trademark of Apex Brands, Inc., a Division of Apex Tool Group, LLC
www. .com [e-mail]1.800.561.8187