Gefen EXT-WHD-1080P-LR-TX User manual

EXT-WHD-1080P-LR-TX
EXT-WHD-1080P-LR-RX
User Manual
Wireless for HDMI 5 GHz
w/ Dual Inputs and Local Output
Release A2
*Preferred

ii
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this product near water.
6. Clean only with a dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s
instructions.
8. Do not install or place this product near any heat sources such as radiators, heat
registers, stoves, or other apparatus (including ampliers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized
plug has two blades with one wider than the other. A grounding type plug has two
blades and a third grounding prong. The wide blade or the third prong are provided for
your safety. If the provided plug does not t into your outlet, consult an electrician for
replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
11. Only use attachments/accessories specied by the manufacturer.
12. To reduce the risk of electric shock and/or damage to this product, never handle or
touch this unit or power cord if your hands are wet or damp. Do not expose this
product to rain or moisture.
13. Unplug this apparatus during lightning storms or when unused for long periods of time.
14. Refer all servicing to qualied service personnel. Servicing is required when the
apparatus has been damaged in any way, such as power-supply cord or plug is
damaged, liquid has been spilled or objects have fallen into the apparatus,
the apparatus has been exposed to rain or moisture, does not operate normally,
or has been dropped.
15. Batteries that may be included with this product and/or accessories should never be
exposed to open ame or excessive heat. Always dispose of used batteries
according to the instructions.
Important Safety Instructions

iii
This device complies with part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a
class B digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and if
not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and Receiver unit
• Connect the equipment into an outlet on a circuit different from that to which the
Receiver unit is connected
• Consult the dealer or an experienced radio/TV technician for assistance.
In order to maintain compliance with FCC regulations, shielded cables must be used with
this equipment. Operation with non-approved equipment or this equipment. Operation with
non-approved equipment or unshielded cables is likely result in interference to radio and
TV reception. The user is cautioned that changes and modications made to the equipment
without the approval of the manufacturer could void the user’s authority to operate this
equipment.
FCC Statement

iv
Technical Support
[phone] [phone]
8:00 AM to 5:00 PM Monday - Friday, Pacic Time
Fax
[phone]
Email
[email protected]
Web
http://www.gefen.com
Mailing Address
Gefen, LLC
c/o Customer Service
20600 Nordhoff St.
Chatsworth, CA 91311
Product Registration
Register your product here: http://www.gefen.com/kvm/Registry/Registration.jsp
Contacting Gefen Technical Support

vv
• The Gefen Syner-G Software Suite is a free downloadable application from Gefen
that provides rmware upgrades for this product. Always make sure that the Wireless
for HDMI 5 GHz w/ Dual Inputs and Local Output is running the latest rmware.
• Obstructions such as walls and furniture and RF interference could reduce reception
distance.
• This product operates in the 5 GHz RF region, and features a specic number of
channels. Other 5 GHz transmitters, including WiFi routers, may be occupying the
same channels and may cause reception issues.
• Due to different transmission power levels, using this product with the Wireless for
HDMI 5 GHz (Gefen part no. EXT-WHD-1080P-SR) is not recommended.
• Using multiple Sender and Receiver units:
► US Models: Up to 8 Sender units can be registered per Receiver unit. Up
to 4 Sender/Receiver systems can be operated in the same environment,
simultaneously.
► EU Models: Up to 8 Sender units can be registered per Receiver unit. Up
to 2 Sender/Receiver systems can be operated in the same environment,
simultaneously.
► Each Sender and Receiver unit must placed at least 1 meter apart for optimum
performance. If additional Sender / Receiver pairs are to be used, each set of
units must be placed beyond the reception range (100 feet / 30 meters) of the
other Sender / Receiver pairs in order to prevent interference.
• This product is not compatible with the Wireless for HDMI Extender LR (Gefen part
no. GTV-WHD-1080P-LR) or the Wireless for HDMI Extender SR (Gefen part no.
GTV-WHD-1080P-SR).
Wireless for HDMI 5 GHz w/ Dual Inputs and Local Output is a trademark of Gefen, LLC.
© 2015 Gefen, LLC. All Rights Reserved. All trademarks are the property of their respective owners.
Gefen, LLC reserves the right to make changes in the hardware, packaging, and any accompanying documentation
without prior written notice.
Operating Notes
This product uses UL listed power supplies.
Pb

vi
Features and Packing List
Features
• Wireless extension of HDMI up to 100 feet (30 meters)
• Supports resolutions up to 1080p Full HD, up to 7.1 channels of LPCM digital audio,
and up to 5.1 channels of Dolby® and DTS® formats
• Transmits through obstacles - does not require line-of-sight
• Long Range performance makes it ideal for multi-room use
• IR Back Channel for source control with carrier frequency selector
• HDMI Features Supported
►CEC
►12-bit Deep Color
►3DTV pass-through
►HDCP pass-through
► Lip Sync
• Uncompressed High Denition A/V from source to display
• Less than 1 frame latency
• AES 128 Encryption
• Compatible with legacy DVI displays
• Sender Unit
►2 HDMI Inputs
►Local HDMI “Mirrored” Output
►IR Output port and included Emitter Array for source control
► Ideal for use with 2 sources in a xed home theater type installation
►Flexible mounting options: ¼-20 thread, wall mounting, shelf placement
• Receiver Unit
►IR Extender module included for hidden installations
► Small and compact form factor - can be installed behind the TV
►Flexible mounting options: ¼”-20 thread, wall mounting, shelf placement
• Handheld IR remote for easy setup and operation
• Firmware update via Mini-USB port using Gefen Syner-G™ software
• WHDI 1.0, FCC Part 15, IC, and ETSI-compliant
• Additional Sender units (Gefen part no. EXT-WHD-1080P-LR-TX) available separately

vii
Packing List
The Wireless for HDMI 5 GHz w/ Dual Inputs and Local Output ships with the items listed
below. The packing contents for each product are listed below. If any of these items are
not present in the box when you rst open it, immediately contact your dealer or Gefen.
EXT-WHD-1080P-LR
• 1 x Wireless for HDMI 5 GHz LR Sender Unit
• 1 x Wireless for HDMI 5 GHz LR Receiver Unit
• 2 x 5 ft. HDMI Cables (M-M)
• 1 x 5 ft. USB to Mini USB Cable
• 1 x 3 ft. USB to DC plug Cable
• 2 x 5V DC Power Supplies with changeable AC plugs
• 1 x IR Remote Control
• 1 x IR Emitter Array Cable
• 1 x IR Extender Module
• 4 x Screws and Wall Anchors - for wall-mounting the Sender and Receiver
• 1 x Quick-Start Guide
EXT-WHD-1080P-LR-TX
• 1 x Wireless for HDMI 5 GHz LR Sender Unit
• 1 x 5 ft. HDMI Cable (M-M)
• 1 x 3 ft. USB to DC plug Cable
• 1 x 5V DC Power Supply with changeable AC plugs
• 1 x IR Emitter Array Cable
• 2 x Screws and Wall Anchors - for wall-mounting the Sender
• 1 x Quick-Start Guide
Features and Packing List
1080P
®
HDCP
Deep Color Support
Up to 8
Senders

viii
Table of Contents
1 Getting Started
Introduction............................................................................................................ 2
Sender Unit ................................................................................................... 2
Receiver Unit................................................................................................. 5
IR Remote Control ........................................................................................ 7
Installing the Batteries................................................................................... 8
Installation ............................................................................................................. 9
Connection Instructions................................................................................. 9
Sample Wiring Diagram .............................................................................. 10
2 Basic Operation
The Linking Process............................................................................................ 14
Switching Sources............................................................................................... 16
Getting Source Information ................................................................................. 18
Setting the IR Frequency..................................................................................... 20
Using Multiple Sender Units................................................................................ 21
Registering Sender Units ............................................................................ 21
Selecting a Sender Unit .............................................................................. 26
Changing the Name of a Sender Unit ......................................................... 28
Removing Sender Units .............................................................................. 31
3 Appendix
Surface-mounting Instructions............................................................................. 36
LED Indicator Messages ..................................................................................... 37
Icon Messages .................................................................................................... 39
Supported Resolutions........................................................................................ 40
Specications ...................................................................................................... 41
Index.................................................................................................................... 43

ix

Wireless for HDMI 5 GHz
w/ Dual Inputs and Local Output
1 Getting Started

page | 2
Page Title
Sender Unit
®
Wireless for HDMI 5 GHz S
w/ Dual Inputs and Local Output
Input1 2 Info
DC 5V
IR OUT
SERVICE
HDMI 1 HDMI 2 HDMI OUT
Input1 2 Info
®
Wireless for HDMI 5 GHz S
w/ Dual Inputs and Local Output
Input1 2 Info
DC 5V
IR OUT
SERVICE
HDMI 1 HDMI 2 HDMI OUT
Input1 2 Info
®
Wireless for HDMI 5 GHz S
w/ Dual Inputs and Local Output
Input1 2 Info
DC 5V
IR OUT
SERVICE
HDMI 1 HDMI 2 HDMI OUT
Input1 2 Info
Introduction
Getting Started Getting Started
2 31
7
9
4 5 6 8

page | 3
Page Title
ID Name Description
1 1, 2 These LED indicators will glow solid blue to
indicate the currently selected input.
2 Input Press and release this button to select the
desired input.
3 Info Press this button to display the info screen
on the connected display. The LED indicator
indicates the current state of the Sender unit.
See LED Indicator Messages (page 37)for
more information on LED messages.
4 DC 5V Connect the included power supply from
available AC outlet to this power connector.
5 HDMI 1, HDMI 2 Connect the included HDMI cables from each
HD source to these HDMI inputs.
6 HDMI Out Connect an HDMI cable from this connector
to a local HD display. The local display
allows monitoring of the HD source at the
Sender unit.
®
Wireless for HDMI 5 GHz S
w/ Dual Inputs and Local Output
Input1 2 Info
DC 5V
IR OUT
SERVICE
HDMI 1 HDMI 2 HDMI OUT
Input1 2 Info
Introduction
Getting Started
10

page | 4
Page Title
ID Name Description
7 IR Out Connect the included IR emitter array from
this jack to the HD sources to control the
source from the viewing location.
8SERVICE This mini-B USB port is used for rmware
upgrades using Gefen Syner-G™.
9 IR sensor This IR sensor receives signals from the
included IR remote control.
10 Tripod connector This 1/4” 20-thread hole can be used to
connect the Sender unit to a camera tripod.
Introduction
Getting Started Getting Started

page | 5
Introduction
Getting Started
Receiver Unit
®
Input
Info
1
2
Wireless for HDMI 5 GHz R
HDMI IR IN
®
Input
Info
1
2
Wireless for HDMI 5 GHz R
HDMI IR IN
®
Input
Info
1
2
Wireless for HDMI 5 GHz R
HDMI IR IN
1
2
3
4 5
9
6 7
8

page | 6
Introduction
Getting Started
ID Name Description
1 Info Press this button to display the info screen
on the connected display. The LED
indicator indicates the current state of the
Receiver unit. See LED Indicator Messages
(page 37)for more information on LED
messages.
2 Input Press and release this button to select the
desired input.
3 1, 2 These LED indicators will glow solid blue to
indicate the selected input on the Sender unit.
4Mini-B USB port Connect the included power supply with the
mini-B USB connector to this port.
5USB port This port is factory use only.
6 HDMI Connect an HDMI cable from this connector
to an HD display.
7 IR In Connect the included IR Extender to this port,
if required.
8 Tripod connector This 1/4” 20-thread hole can be used to
connect the Receiver unit to a camera tripod.
9 IR sensor This IR sensor receives IR signals. See
Connection Instructions (page 9).
®
Input
Info
1
2
Wireless for HDMI 5 GHz R
HDMI IR IN
8
Getting Started

page | 7
IR Remote Control
ID Name Description
1 IR Press this button to set the IR frequency
required by the source device to use the IR
emitter array. See Setting the IR Frequency
(page 20)for more information.
2 Input Press this button to select the desired input
on the active Sender unit.
3▲, ▼, ◄, ► Press these buttons to select the desired
option in the Information Window.
4 OK Press this button to accept the current
change within the OSD.
5Sender Press this button to add, delete, or edit
Sender units. See Using Multiple Sender
Units (page 21)for more information.
6 Battery cover See Installing the Batteries (page 8) for
more information.
Input
RMT-WHD-1080P
OK
SenderIR
*Preferred
®
+
-
+
-
Input
RMT-WHD-1080P
OK
SenderIR
*Preferred
®
+
-
+
-
Introduction
Getting Started
6
4
1 5
2
3

page | 8
Introduction
Getting Started
Installing the Batteries
1. Push and pull-up the tab at bottom of the IR remote to remove the battery cover.
2. Make sure that the batteries are installed with the correct polarity, as shown in the
illustration, below. Always use two 1.5V AAA-type batteries.
3. Replace the battery cover. Push the battery cover down until the tab snaps in place.
Warning!
Risk of explosion if battery is replaced by an incorrect type. Dispose of used
batteries according to the instructions.
Input
RMT-WHD-1080P
OK
SenderIR
*Preferred
®
+
-
+
-
Input
RMT-WHD-1080P
OK
SenderIR
*Preferred
®
+
-
+
-
Battery cover tab
Battery cover
Getting Started

page | 9
Connection Instructions
►Video
1. Connect one of the included HDMI cables from the HD source to the HDMI 1 port on
the Sender unit.
2. Connect the other (included) HDMI cable from a second HD source to the
HDMI 2 port.
3. Connect an HDMI cable from the HDMI Out port on the Sender unit to a local HD
display. This display will allow monitoring of the HD source.
For best results, the local display should be identical, or have the same capabilities
as the main display in terms of resolution and features (e.g. CEC, 3D, 1080p).
►IR Control - see Sample Wiring Diagram (page 10)
4. Connect the included IR emitter array from the IR Out port on the Sender unit to the
HD sources. This will allow the sources to be controlled from the viewing location.
5. Connect the included IR Extender to the IR In port on the Receiver unit.
►Power
6. Connect the included power supplies:
• Connect the power supply with the round power connector to the Sender unit.
• Connect the power supply with the mini-B USB connector to the Receiver unit.
Installation
Getting Started
Information
Once the IR extender is connected to the Receiver unit, the IR sensor on
the Receiver unit will be disabled.

page | 10
Sample Wiring Diagram
Getting Started
Installation
HDMI Display
at Remote
Viewing Location
IR Extender
IR Emitter
Array
EXT-WHD-1080P-LR
Receiver unit
EXT-WHD-1080P-LR
Sender unit
Local HDMI Display
HDMI Source 1
HDMI Source 2
(Up to 100 feet)
HDMI CABLE
EXT-WHD-1080P-LR
IR IN
IR OUT