Gefen ex-tend-it 4x4 HDTV Matrix User manual

4x4 HDTV
Matrix
USER MANUAL
www.gefen.com

Technical Support:
Telephone [phone]
[phone]
Fax [phone]
Technical Support Hours:
8:00 AM to 5:00 PM Monday through Friday.
Write To:
Gefen Inc.
C/O Customer Service
6265 Variel Ave.
Woodland Hills, CA91367-9897
Notice
Gefen Inc. reserves the right to make changes in the hardware, packaging and any
accompanying documentation without prior written notice.
The 4x4 HDTV Matrix is a trademark of Gefen Inc.
© 2006 Gefen Inc., All Rights Reserved
ASKING FOR ASSISTANCE

TABLE OF CONTENTS
Introduction / Operation Notes
Features
Panel Layout
Using the 4x4 HDTV Matrix
RMT16-IR Installation
Dip Switch Guidelines
IR Codes
RS-232 Interface
4x4 HDTV Matrix Rack Mount Diagram
Specifications
Terminology
Warranty
1
2
3
4
5
6
7
8
9
10
11
12

INTRODUCTION
Thank you for purchasing the 4x4 HDTV Matrix.
The 4x4 HDTV Matrix switches four HDTV sources to any four DVI displays.
The 4x4 HDTV Matrix switcher has four DVI inputs and four DVI outputs. Matrix input #1
and the DVI port of HDTV source #1 connects using a male to male DVI cable. The DVI
port of HDTV source #2 connects to DVI input #2. The DVI port of HDTV source #3 con-
nects to DVI input #3. The DVI port of HDTV source #4 connects to DVI input #4. There
are four (4) DVI outputs connecting to four (4) different displays.
Note: The switching is done by using either the the RMT-16-IR remote control or through
the RS232 port. The 4x4 HDTV Matrix is rack mountable.
1
OPERATION NOTES
READ THESE NOTES BEFORE INSTALLING
OR OPERATING THE 4X4 HDTV MATRIX
• The 4x4 HDTV Matrix is housed in a metal box for better RF shielding.
• The 4x4 HDTV Matrix works with all DVI and HDMI displays.
• The 4x4 HDTV Matrix supports both AUDIO and VIDEO signals.
• The 4x4 HDTV Matrix is fully HDCP compliant.

2
FEATURES
Features
• Allows any HDTV display to view any source at any time
• Allows any source to be displayed on multiple displays at the same time
• Maintains resolutions up to 1080p, 2K, and 1920x1200
• Maintains highest HDTV single link video resolution
• Maintains highest HDTV digital audio signal
• Supports HDCP compliant devices
• DVI or HDMI to DVI cables are used to connect the inputs and outputs of the matrix
• Each display's inputs can be switched with the IR remote control or through RS232
Includes:
(1) 4x4 HDTV Matrix
(4) DVI 6ft Male to Male Cables
(1) 24VDC Power Supply
(1) User Manual
(1) RMT-16IR Remote Control
(1) Rack Ears

PANEL LAYOUT
3
Display 1 LED
Indicator
Front Panel
RS232 Controller Port
Display 2 LED
Indicator Display 3 LED
Indicator Display 4 LED
Indicator
IR Sensor
IR Extender Eye Port Power Indicator
Back Panel
Connects to 24VDC
Power Supply
DVI Inputs DVI Outputs

Connect all the sources to the DVI inputs on the 4x4 HDTV Matrix, using the
supplied cables.
Connect the HDMI/DVI displays to the outputs on the 4x4 HDTV Matrix.
Connect the 24VDC powersupply to the 4x4 HDTV Matrix
Controlling the 4x4 HDTV Matrix using the RMT16-IR:
Pressing Buttons... Switches...
1-4 Display 1 to view Source 1, 2, 3, or 4
5-8 Display 2 to view Source 1, 2, 3, or 4
9-12 Display 3 to view Source 1, 2, 3, or 4
13-16 Display 4 to view Source 1, 2, 3, or 4
*Note for computers connected to the HDTV Matrix - When your computer
boots up, it looks for an EDID (extended display identification data) from the dis-
play to tell it what monitor is connected and what resolution to output. During boot
up of the computer you should have ONLY one output selected to one input at a
time so that the computer gets the EDID of the display that is selected. If you have
multiple outputs selected to one computer, the computer will read the EDID of the
last output selected to it. If all your displays are the same, or all displays are ca-
pable of running at the same resolution then this step does not matter.
You can also use a DVI Detective to illiminate the need to have that matrix selected
to the computer during bootup.
USING THE 4X4 HDTV MATRIX
1
2
3
4
4

5
RMT16-IR Installation
1. Remove battery cover from the back of the RMT16-IR remote.
2. Verify that dip switches 1 & 2 are in the down (OFF) position.
3. Insert the battery, hold the battery so that you can see the positive side facing up. The
side that is not marked must be facing down.
4. Test the RMT16-IR remote by pressing ONLY one button at a time. The indicator light
on the remote will flash once each time you press a button. WARNING: Do not press
multiple buttons simultaneously and do NOT press buttons rapidly. These actions will
cause the remote to reset and steps 1-4 will have to be repeated.
Note: The RMT16-IR ships with two batteries. One battery is required for operation, the
second battery is complimentary.

6
DIP SWITCH GUIDELINES
Inside the 4x4 HDTV Matrix is a bank of Dip Switches. Below is a table describing their
functions. By default, all switches are set to the Off position.
Dip Switch # Name Description
1 Switching Delay Adds a 3 second delay to switching
2 On Board EDID Feeds a Generic HDMI EDID (720p/1080i)
to all Inputs
3 IR Code Dip Switch Corresponds to Dip Switch 1 on RMT16-IR
4 IR Code Dip Switch Corresponds to Dip Switch 2 on RMT16-IR
5 Unused
6 Unused
7 Unused
8 Edge Select +Edge Pixels
How to open the 4x4 HDTV Matrix:
To access the dip switches, first remove the 18 hex nuts on the back of the unit (16
located above each DVI port and 2 adjacent to the RS232 port). Remove the 5 Philips
screws under the unit and the 4 screws on each side of the unit. Now carefully remove
the cover of the 4x4 HDTV Matrix.
12345678

7
IR CODES
In the event of IR conflicts, please do the following:
1. Remove the battery cover from the back of the RMT16-IR remote.
2. Locate the Dip Switches above the batteries
3. Switch the Dip Switches on the RMT16-IR to any of the combinations pictured below.
4. Dip Switches 1 and 2 in the RMT16-IR correspond with Dip Switches 3 and 4 inside
the 4x4 HDTV Matrix respectively. Switch the switches inside the 4x4 HDTV Matrix to
match the same Remote Channel as the RMT16-IR. The 4x4 HDTV Matrix is now set
to a new IR Code.
12
Remote Channel 0:
12
Remote Channel 1:
12
Remote Channel 2:
12
Remote Channel 3: