Gemmy 220418 User manual

E-1
IMPORTANT SAFETY INSTRUCTIONS
WHEN USING ELECTRICAL PRODUCTS, BASIC PRECAUTIONS
SHOULD ALWAYS BE FOLLOWED, INCLUDING THE FOLLOWING:
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT OPEN THE COVER. NO USER
SERVICABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED PERSONNEL.
WARNING: This product is recommended for indoor and outdoor use. Please read this manual
carefully prior to using the unit.
WARNING:
1. Do not secure the wiring of the product with staples or nails, or place on sharp hooks or nails.
2. Do not let lamps rest on the supply cord or on any wire.
3. Do not close doors or windows on the product or extension cords as this may damage the wire insulation.
4. Do not cover the product with cloth, paper or any material not part of the product when in use.
5. Do not use seasonal products outdoors unless marked suitable for indoor and outdoor use. When products are
used in outdoor applications, connect the product to a Ground Fault Circuit Interrupting (GFCI) outlet. If one is not
provided, contact a qualified electrician for proper installation.
6. This seasonal use product is not intended for permanent installation or use.
7. Do not mount or place near gas or electric heaters, fireplace, candles or other similar sources of heat.
8. Unplug the product when leaving the house, when retiring for the night, or if left unattended.
9. This is an electric product-not a toy! To avoid risk of fire, burns, personal injury and electric shock it should not be
played with or placed where small children can reach it.
10. Do not use this product for other than its intended use.
11. Do not hang ornaments or other objects from cord, wire, or light string.
12. This product employs overload protection (fuse). A blown fuse indicates an overload or short-circuit situation. If the
fuse blows, unplug the product from the outlet. Also unplug any additional strings or products that may be attached
to the product. Replace the fuse as per the user servicing instructions (follow product marking for proper fuse rating)
and check the product. If the replacement fuse blows, a short-circuit may be present and the product should be
discarded.
13. This product has a polarized plug (one blade is wider than the other) as a feature to reduce the risk of electric shock.
This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still
does not fit, contact a qualified electrician. Do not use with an extension cord unless plug can be fully inserted. Do
not alter or replace.
14. Read and follow all instructions that are on the product or provided with the product.
SAVE THESE INSTRUCTIONS
USE AND CARE INSTRUCTIONS
1. When the product is placed on a live tree, the tree should be well maintained and fresh. Do not place on live trees in
which the needles are brown or break off easily. Keep the tree holder filled with water.
IMPORTANT: PLEASE READ ALL THE INSTRUCTIONS
CAREFULLY BEFORE USING THIS PRODUCT.
Failure to follow all instructions listed below may result in electric shock, fire and/or serious personal injury.
WARNING: Not recommended for children under 12 years of age. As with all electric products, precautions
should be observed during handling and use to prevent electric shock.
INSTRUCTIONS
E

E-2
2. If the product is placed on a tree, the tree should be well secured and stable.
3. Before using or reusing, inspect product carefully. Discard any products that have cut, damaged, or frayed wire
insulation or cords, cracks in the lampholders or enclosures, loose connections, or exposed copper wire.
4. When storing the product, carefully remove the product from wherever it is placed, to avoid any undue strain or stress
on the product conductors, connections, and wires.
5. When not in use, store neatly in a cool, dry location protected from sunlight.
CAUTION: To reduce the risk of fire and electric shock:
1. Do not install on trees having needles, leaves or branch coverings of metal or materials which look like metal.
2. Do not mount or support wires in a manner that can cut or damage wire insulation.
CONTENTS
ILLUSION PROJECTOR ASSEMBLY INSTRUCTIONS
Set-up Approximately 1-5 minutes.
1. Remove contents from packaging.
2. Open the lid of the Illusion Projector (turn
right or left), insert desired image slide.
(see Illustration 1)
3. Push A through the circle, insert the
grooves of Illusion Projector, and tighten
the circle, then adjust the angle of Illusion
Projector. (See Illustration 2) and tighten
screw B.
4. Get together the Tripod Stake for outdoor
using, and separate the Tripod Stake for
indoor using. (see Illustration 3)
5. Plug into receptacle or other outlet device to
activate your Illusion Projector.
6. When plugged in, the projected image gradually transitions from fuzzy to clear to blurred out—then repeats. This is the
normal operation of the projected image.
7. To deactivate, unplug.
USER SERVICING INSTRUCTIONS
Fuse Replacement
WARNING: Risk of Fire: Replace only with same size and type of fuse.
WARNING: Risk of Fire: Do not replace the attachment plug. Contains
a safety device (fuse) that should not be removed. Discard
product if attachment plug is damaged.
1. Grasp plug and remove from the receptacle or other outlet device. Do not unplug by
pulling on the cord.
2. Open fuse cover. Slide open the fuse access cover on top of the attachment plug
towards blades. (See illustration)
3. Remove fuse carefully.
4. Replace fuse only with 5 Amp Max, 125 Volt fuse (provided with product).
5. Close the fuse cover. Slide closed the fuse access cover on top of the attachment plug.
Illustration 1 Illustration 2 Illustration 3
Working
Fuse
Replace
Fuse
Image Slides
Illusion Projector
2pcs
6pcs
Fuse
1pc
1pc
Stake
A
B
Ground

E-3
WARNING
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device
may not cause harmful interference, and (2) this device must accept any interference received, including interference that
may cause undesired operation.
CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of thefollowing measures:
• Reorient or relocate the receiving antenna.
• Increase the distance between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
THIS INSTRUCTION SHEET APPLIES TO ITEM NUMBERS
220418 220583 221281 221548 221549 221550 221552
221553
Visit WWW.GEMMY.COM for more information.
©2018 GEMMY INDUSTRIES CORP.
117 WRANGLER DRIVE. SUITE 100
COPPELL, TX 75019 U.S.A.
1 [phone]
MADE IN CHINA / PRINTED IN CHINA