Gen IV Technology 8 CH STAND-ALONE DVMR User manual

User Manual
Thank you for purchasing our product.
Please read this User s Manual before
using the product.
STAND-ALONE DVMR
ALL ABOUT IMAGE RECOGNITION & PROCESSING
8 Channel Digital Video Multiplex Recorder
VER 2.0
ALL ABOUT IMAGE RECOGNITION & PROCESSING
8 CH STAND-ALONE DVMR The most stable and reliable real stand-alone Digital Video Multiplex Recorder

ALL ABOUT IMAGE RECOGNITION & PROCESSING
SAFETY PRECAUTIONS
CAUTION
RISK OF ELECTRIC
SHOCK. DO NOT OPEN!
CAUTION : TO REDUCE THE RISK OF ELECTRICAL SHOCK, DO NOT OPEN COVERS.
NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
This label may appear onthe bottom of the unit due to space limitations.
The lightning flash with an arrowhead symbol within anequilateraltriangle is intended
to alert the user to the presence ofuninsulated “ dangerous voltage” withinthe
product’s enclosure that may be of sufficient magnitude to constitute a risk of electric
shock to persons.
The exclamation point within anequilateral triangle is intended to alert theuserto
presence of important operating and maintenance (Servicing) instructions in the
literature accompanying the appliance.
WARNING : TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE UNITS NOT
SPECIFICALLY DESIGNED FOR OUTDOOR USE TO RAIN OR MOISTURE.
Attention: installation should be performed by qualified service Personnelonly in
accordance with the National Electrical Code or applicable local codes.
Power Disconnect. Units with or without ON-OFF switches have power supplied to
the unit whenever the power cord is inserted into the power source ; however, the unit
is operational only when the ON-OFF switch is in the ON position. The power cord is
the main power disconnect for all unites.
ALL ABOUT IMAGE RECOGNITION & PROCESSING
8 channel stand-alone DVMR
ALL ABOUT IMAGE RECOGNITION & PROCESSING
8 channel stand-alone DVMR

ALL ABOUT IMAGE RECOGNITION & PROCESSINGALL ABOUT IMAGE RECOGNITION & PROCESSING
8 channel stand-alone DVMR
FCC INFORMATION
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1)This device may not cause harmful interference, and
(2)This device must accept any interference received,
including interference that may cause undesired operation.
A CLASS A computing device subject to certification by the Commission shall be identified pursuant to
par.2.925 et Seq of thechapter. In addition, the label shall includethe following statement:
Wherea device is constructed in two or more sections connected by wires and marketed together, the
statement specified in this Section is required to be affixed only to the main control unit.
The users manual or instruction manual for the EUT shall contain the following statement or eqivalent.
Caution : Changes or Modifications not expressly approved by the party responsible forcompliance could
void the users authority to operate the equipment.
If theEUT requires accessories such as special shielded cables and/or connectors to enable compliance
with emission limits, the instruction manual for the EUT shall include appropriate instructions on the first
page of the text concerned with the installation of the device that these special accessories must be used
with the device. It is the responsibility of the user to usethe needed special accessories supplied with the
equipment.
For a CLASS A digital device or peripheral, the instructions furnished the user shall include the following or
similar statement placed in a prominentlocation in the text ofthe manual.
Note : This equipment has been tested and found to comply with the limits for a CLASS a digital device,
pursuant to Part15 of FCC Rules. These limits are designed toprovide reasonable protection against
harmful interference when the equipment isoperatedin a commercial environment. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio communications. Operation ofthe this
equipment in a residential area is likely to cause harmfulinterference in which case the user will be required
to correct the interference at his own expense.
ALL ABOUT IMAGE RECOGNITION & PROCESSING
8 channel stand-alone DVMR
ALL ABOUT IMAGE RECOGNITION & PROCESSING

1
Chapter 1 . Product package
Chapter 2. Installation procedure
1-1. The contents of package 3
1-2. Name and function of each button (front panel) 4
1-3. Name and function of each button (rear panel) 5
2-1. Camera connection 6
2-2. Monitor connection (Composite monitor) 6
2-3. Monitor connection (S-VHS) 7
2-4. VCR & VIDEO PRINTER connection 7
2-5. Sensor connection 8
2-6. Network connection 8
2-7. HDD connection 9
2-8. Power connection 9
Chapter 3. Operation
3-1. DVR SYSTEM Log-in 10
3-2. Recording 11
3-3. Playback 14
3-4. Set-up 16
1. Basic operation 16
2. CAMERA SETUP 16
3. DISPLAY SETUP 17
4. TIME/DATE SETUP 19
5. RECORD SETUP 19
6. HDD MANAGEMENT 21
7. MISCELLANEOUS SETUP 21
8. TCP/IP SETUP 24
Chapter 4. Specification and Configuration
4-1. SPECIFICATIONS 27
4-2. Configuration Stand-alone DVMR 28
4-3. RS-232C Hex-code table 28
4-4. Arrange of RS 485 and RS-232C pin 29
9. FACTORY DEFAULT 26
ALL ABOUT IMAGE RECOGNITION & PROCESSING
ALL ABOUT IMAGE RECOGNITION & PROCESSING
8 channel stand-alone DVMR Table of Contents
ALL ABOUT IMAGE RECOGNITION & PROCESSING
8 channel stand-alone DVMR
Chapter 5. Menual for Remote Viewer Software(TCP/IP) 30

Before reading this document
1. This document is intendedfor both the administratorand users of stand alone DVMR.
2. This manual contains information for configuring, managing and using stand alone DVMR properly.
3. To prevent fire or electrical shock, do not expose the product to heat or moisture.
4. Be sure to read this manual before using stand alone DVMR Model, even before installing HDD.
8. For questions and technical assistance of this product, contact your local dealer.
About this document
2
Before installing stand alone DVMR, be sure to thoroughly review and follow the instructions in this
User’s Manual. Pay particular attention to the parts those are marked NOTICE.
Also, when connecting with externalapplication, first turn the power OFF and follow
THE instruction in manual forappropriate installation.
ALL ABOUT IMAGE RECOGNITION & PROCESSING
5. Check electricity at the place you want to install the DVMR unit is stable and meets our
electricity requirements.
Unstable electricity will cause malfunction of the unit or give critical damage to the unit.
6. Several chips on the main board of the DVMR unit and hard disk drive inside the unit generate
heat, and it must be properly discharged.
Do not put any objects just beside exhaust port(fan) on the left side of the unit and do not close
up an opening (fresh air in-take)on the right sideof the unit..
7. Putthe DVMR unit at well-ventilated place and do not put heat-generating objects onthe unit.
When it is installed inside 19 inch mounting rack together with other devices, please check built-
in ventilation fan of the rack is properly running.
8 channel stand-alone DVMR
ALL ABOUT IMAGE RECOGNITION & PROCESSING
8 channel stand-alone DVMR 5.Menual for Remote Viewer Software(TCP/IP)
37
Maximum playback speed of DVMR is 60x.
10 : Command button.
We have 3 different buttons, that are, save, print, and event, and those buttons work only when stop
button is pressed.
a)Save
During searching recorded pictures, you can save pictures one by one in the folder in client PC by
pressing save button. Press Save button while you see recorded picture, and picture you selected by
pressing Save button shall be save on the folder you already assigned under the file name of year-month-
day-hour-minute-second in jpg format.
b)Print
During searching recorded pictures, you can print picture, one by one, you see, by pressing Print button.
c)Event
Press event button to see alarm list saved in DVMR unit, and you can search recorded pictures based on
event list by clicking any one of list.
11 : Calendar.
You can select date and time to search pictures recorded at selected time and date. You can refer to start
and end of recording in 7.
Notice : From time to time, connection shall be cut unexpectedly due to conditions of network line.
Whenever it is cut, quit search window by pressing power switch(1), and then press connect button in live-
view window and scan button to enter into search window again, to continue searching.
Notice : Compatibility of Remote Viewer Software with different kinds of operating systems and PC
hardware may not be simply specified due to the characteristics of network that it is much related with not
only PC hardware and operating system but also other software installed on the client PC and conditions
of network(internet) line. Basically, Remote Viewer Software is compatible with typical Windows operating
system from Windows 98 to Windows XP.
Notice : To see continuous live view, we recommend not to select motion recording in RECORD SETUP
menu of DVMR. If it is set at motion recording in SETUP menu of DVMR, image transmission is done only
there is motions detected.
Notice : While you search recorded data using client software in client PC, DVMRunit to which you access
via IP network is in playback mode, and no recording is done as far as you search recorded data.
However, while you are in connection with DVMR unit via IP network for live view, DVMR unit continues to
record but at a little lowered recording rate. Therefore we recommend you to access to DVMR unit only
when it is necessary.
Speed of playback in DVMR unit according to scan rate set in 4-7-b).
Scan rate set in 4-7-b) or
or
1x
2x
4x
8x
16x
32x
64x
1x
1x
1x
1x
1x
1x
1x
1x
2x
4x
8x
16x
30x
60x

Chapter 1 . Product Package
1-1. The contents of package
1. 8 ch stand-alone DVMR unit
ALLABOUT IMAGERECOGNITION& PROCESSING
Stand-alone DVR
8 channel
Stand-alone DVR
Describe how to install and operate this DVMR unit.
4. DC power adapter and power cable
Convert AC 110V or AC 220V into DC 12V to supply to DVMR unit.
3. Remote controller
IR remote controller enables an user to operate DVMR unitapart from the unit.
3
2. User’s manual for 8 ch DVMR
POWER
36
5. Search recorded pictures via IP network
Function of each button in search window :
1: Power switch. Press power switch to quit.
2: Full screen button. Press full screen button to search recorded picture channel by channel in full screen.
3: Quad button. Press Quad button to search recorded pictures in quad screen, 4 pictures from 4 channels at the
same time.
4: Screen division button : If press “+” button, it screen division is changed from 4 to 9 or from 9 to 16. “-“ button
reduce screen division.
5: Time of recording. It indicates when the pictures you see recorded.
6: Channel selection button. Press any one from 1 to 4 to see picture of corresponding channel, if you first chose full
screen button(2).
7: Time selection button. You can set time to search by dragging yellow mover to the left or right. See time displayed
in green color and find an exact time from which you search.
8: Start and end of recording. It shows time from which recording started and recording ended. Further it show time
from which search will start.
9: Search operation button. You can search recorded data using various buttons useful for searching effectively as
follows.
ALL ABOUT IMAGE RECOGNITION & PROCESSING
8 channel stand-alone DVMR Product package
Play fast backward (Speed set in SYSTEM SETTING)
Move to start of recording (Press stop button first before this button)
Play Backward(x1)
Move to previous hour(on the hour). Press stop button first before this button.
Stop
Play forward(x1)
Move to next hour(on the hour)
Play fast forward(Speed set in SYSTEM setting)
Move to end of recording(Press stop button first before this button)
ALL ABOUT IMAGE RECOGNITION & PROCESSING
8 channel stand-alone DVMR 5.Menual for Remote Viewer Software(TCP/IP)
OVERWRITE
RECORD
PLAY
SETU P ZOOM
MODE P/T PIP FR Z SE QPLAY MENU
1 2 3 4
ENTER
5678
DIGITALV IDEORE CORDER

35
USER PANTILT COMMAND
-It is to input protocols for specific PTZ camera you will connect to 16 ch DVMR unit, to control PTZ
camera while you see live pictures in the client program.
-You can save protocols of specific PTZ camera in the form of computer file(text file). Prepare text file
of protocol for PTZ camera and save it on your PC. In the User Pantile Command window, press
[Menu] button and again press [Load User PT File].Then you can assign textfile of protocol forPTZ
camera you prepared in advance. It is very convenient function.
-If you want to control PTZ camera using buttons on the front of 16 ch DVMR unit, you must input the
same protocol into DVMR unit in PAN/TILE CMD SETUP.
b) Scan. : Press scan button to enter into search window. Using various operation buttons, you can
search recorded pictures, save selected pictures on client PC, or print pictures. Refer to following
paragraph “3. Search recorded pictures over IP network” for details
8) PTZ control. You can control Zoom, Focus, and Pan/Tilt of camera while you see live pictures via IP network. Of
course, you must first input PTZ protocol for a specific PTZ camera you connected to your DVMR unit, into your
DVMR unit. You can control PTZ camera with various of commands in USER PANTILE COMMAND window above.
When you press corresponding buttons for Pan/Tilt control, press a couple of second every time you press to take
care of data transmission speed through IP network. Otherwise, there is a possibility that given protocol is transmitted
repeatedly, regardless of your intention.
Notice : From time to time, connection shall be cut unexpectedly due to conditions of network line, and you will see
disconnect button( ) is activated. Just press connect button( ) again, and you can continue to see live pictures.
4
1. POWER SWITCH WITH LED : DC power switch with LED
Generally speaking, cutting power to system may cause trouble in DVMR
system or damage to HDD when HDD is in writing process, and we ask you to
press [MENU] button first to protect HDD from being damaged or system
failure before you press DC power switch off in practical operation.
2. MENU : Used to check or change parameters settings in SYSTEM SETUP. After pressing [MENU] button,
input password and press [ENTER] button to enter into SYSTEM SETUP.
3. PLAY/ENTER : Starts playback, and in some functions, it is used as the SELECT key.
Press shortly and it starts playback. If you press this button for a long time, you enter
into GO TO menu to start playback from image you want to start.
4. MODE : Changes screen division. Whenever you press [MODE] button, screen division is changed from
full screen to 4-split screen, 9-split screen in sequence, both in live or playback mode.
To change channel in full screen mode, just press number button.
If you press [MODE] button for a lone time, it changes type of monitor connected to DVMR unit
form COMPOSITE to VGA, or from VGA to COMPOSITE, in case VGA option is included in
DVMR system.
5. P/T : Manages PAN/TILT CONTROLLER. To control PTZ camera connected to DVMR unit, you have to
select model of PTZ camera in PAN TILE CMD SETUP/MISCELLANEOUS SETUP.
6. 1/5,2/6,3/7,4/8 : Chooses each indicated camera in full screen mode. Each button is double number
button, and pressing [1], [2], [3], and [4] for a very short time is for 1, 2, 3, and 4
respectively, and pressing [1], [2], [3], and [4] for a long time is for 5, 6, 7, and 8
respectively.
7. PIP : Assigns PIP (Picture In Picture)
8. FRZ : : Displayed screen is paused.
9. SEQ : To see display screen in rotation from channel number 1, 2, 3, and so on, both in live and playback
mode. It also change Quad screen from 1/2/3/4 to 5/6/7/8.
10987
6
5
4
3
21211
10. ZOOM : Enlarges the display screen by 200%. Digital zooming.
11. Remote Controller Sensor Input Window
12. Direction button : [LEFT], [RIGHT], [UP] and [DOWN].
In playback mode, [LEFT] and [RIGHT] buttons are for selecting playback
direction(forward/backward), and [UP] and [DOWN] buttons are for increasing or
decreasing speed of playback.
NOTICE : If the Input window (IR receiver) is covered, the remote controller may not work.
NOTICE : If several buttons are simultaneously or incorrectly pressed, the system may not be operated unproperly.
1
POWER
ALL ABOUT IMAGE RECOGNITION & PROCESSING
13
13. LED Lamps : Represent status of operation. OVERWRITE/RECORD/PLAYBACK/SETUP.
8 channel stand-alone DVMR 1. Unit Description
1-2. Name and function each button (front panel)
OVERWRITE
RECORD
PLAY
SETUP
14
14. CD-RW DRIVE
ALL ABOUT IMAGE RECOGNITION & PROCESSING
8 channel stand-alone DVMR 5.Menual for Remote Viewer Software(TCP/IP)
MENU PLAY MODE P/T PIP FRZ SEQ ZOOM
1234
ENTER
56 7 8

5
5. LOOP Output
6. VCR Connection
7. MONITOR Connection
8. VGA Connection
10. D/C Power Connection
3. LAN (TCP/IP)
2. Sensor Input/Output
1. RS-232C and RS-485 port Connection
4. Camera Connection
9. S-VHS Connection
NOTICE : When connecting with other applications, be sure to turn off the system.
1
4
2
3
6
7
8
910
ALL ABOUT IMAGE RECOGNITION & PROCESSING
5
8 channel stand-alone DVMR 1. Unit Description
1-3. Name and function each button (Rear panel)
34
7) : Set button. 2 different set buttons
a) Setting : Press this button to input IP Address(or select a unit of 16 ch DVMR unit among many) and
others and to set circular monitoring interval and scan rate, to assign folder where you want
to save pictures you will select during search, to input protocol for PTZ cameras or select any
model of PTZ cameras among many models whose protocols you already input, as following
dialog box.
CONNECTION
-On the Name box, youare requested toinput name of 16 ch DVMR units, in case you want to access to any one
DVMR unit among more than a unit.You can save IP information in Configurations Window and select
name of DVMR unit to which you want to access.
-Input IP Address you already input into DVMR unit(TCP/IP SETUP) in IP ADDRESS.
-Input Port number you already input into DVMR unit in PORT. Just input 8000, which is default port number.
In some cases, port number 8000 is blocked by firewall, and you have to input different number like 8090
which is not blocked.
-Input “admin” in ID.
-Input the same password you set into DVMR unit in PASSWORD. Default password of 16 ch DVMR unit is
blank(null). Youare requested to enter your own password using number keys from 1 to 16 on front panel
of 16 ch DVMR unit
OPTION
-Select circular monitoring interval ranging from 0.1 sec to 10 sec. The smaller it is, the faster picture of each
channel rotates. The absolute circulation interval is a little different from set value depending on data
transfer rate of IP network.
-Select scan rate ranging from 1x to 64x. The larger it is, the faster search speed is. The absolute search speed is a
little different from set value depending on data transfer rate of IP network.
-Reconnection count : In case disconnected due to some reason, client program tries to reconnect after this time.
SAVE OPTION
It is to assign folder on which you wantto save pictures you will select while you search recordedpictures,
picture by picture.
ALL ABOUT IMAGE RECOGNITION & PROCESSING
8 channel stand-alone DVMR 5.Menual for Remote Viewer Software(TCP/IP)
DC12V
VCR
CH1 CH2 CH3 CH4
MONITOR
LOOP
V
G
A
ALARM/ RELAY
CH5 CH6 CH7 CH8
ETHERNET
Comm Port
RS-232C/485
S-VHS
CAUTION
RISKOF ELECTRIC
SHOCK. DONOT OPEN!
CAUTION : TO REDUCE THE RISK O F ELECTRICAL SHOCK, DO NOT OPEN COVERS.
NO US ERS ERVICEA BLE PART SIN SIDE. REF ER SERVIC ING TO QUALI FIED
SERV ICE PERS ONNEL.
WARNNIG : TO PREVENT FIAE OR SHOCK HAZARD, DO NOT EXPOSE UNITS NOT
SPEC IFICALLY D ESIGNE D FOR O UTDOO R USE T OR AIN O R MOISTUR E

33
Now, hit the "Release" button and then hit "Renew". If all goes well, you'll get new information, and it is for your
DVMR unit. Write down this information on separate paper and input IP Address, Subnet Mask, and Default
Gateway into your DVMR to which you want to access via IP network.
⒞ Confirm if IP Address is working by executing pingtest
Execute pingtest with IP Address which you assigned to DVMR unit, check if it is successful before you try to
access to DVMR unit via IP network. If it is not successful, you may not be able to access to DVMR unit via
IP network, and we recommend you to get help from your network administrator.
4. Live view via IP network
Click Remote Viewer icon to view live pictures via IP network.
You will see then following window.
Function of each button in live-view window :
1) : Power switch. Press power switch to quit. Before press power switch button, press disconnect button first.
2) : Connect button. Press connect button to connect to DVMR unit via IP network to see live pictures of DVMR unit.
You will see the same live pictures, which are displayed on monitor of DVMR unit with a certain time delay depending
on transfer rate of IP network.
3) : Disconnect button. Press disconnect button to cut connection to DVMR unit via IP network.
4) : Screen division button. You can select to see pictures of any single channel, 4, 9, and 16 channels at the same
time. You can select channel number from 1 to 16 to see pictures of selected channel. If you selected 4, you swill see
channel number from 1 to 4 are all activated.
5) : Channel number button. You can select channel number to see live pictures from selected channel.
6) : Status window. It shows Date and Time. Further it displays “Connection established” and a circular fan on the left
bottom is rotating when connection button is activated, or “Waiting for connection” when disconnection button is
activated.
2-1. Camera Connection
Connect the camera to the CAMERA INPUT on the Rear Panel of the system.
2-2. Monitor Connection (Composite Connection Method)
Connect the monitor to the MONITOR OUT on the Rear Panel of the system
6
VIDEO
LENS VIDEO
DC
AC24V/DC12
V.P
DC
LEVEL
Rear part of CAMERA
VIDEO A
IN OUT
VIDEO C
IN OUT
VIDEO B
IN OUT
ALL ABOUT IMAGE RECOGNITION & PROCESSING
Notice : Connect camera or monitor to DVMR unit while DC power switch on the front panel is off.
Screen positioning : If picture displayed in your monitor is not at the center of monitor, you can relocate
images to make them shown in the middle of monitor.
Press [P/T] button for a long time to enter into screen position mode, and you
can adjust location of pictures using [UP], [DOWN], [LEFT] and [RIGHT]
buttons. Press [P/T] button for a long time again to quit screen positioning mode.
If you press [ENTER] button in the process of screen positioning mode, location
of pictures return to original location set by manufacturer.
VCR
CH1 …... CH8
MONITOR
LOOP
V
G
A
8 channel stand-alone DVMR 2. Installation
Chapter 2. Procedure
ALL ABOUT IMAGE RECOGNITION & PROCESSING
8 channel stand-alone DVMR 5.Menual for Remote Viewer Software(TCP/IP)
VCRCH1 …... CH8
MONITOR
LOOP
V
G
A

VCRCH1 …... CH8
MONITOR
LOOP
V
G
A
VCR
CH1 …... CH8
MONITOR
LOOP
V
G
A
2-3. Monitor (S-VHS) Connection
Connect S-VIDEO Monitor to MONITOR OUT(S-VHS) on the Rear Panel of the system.
2-4. VCR & VIDEO PRINTER Connection
Connect VCR or VIDEO PRINTER to VCR OUT on the Rear Panel of the system.
7
VIDEO
A
IN OUT
VIDEO
C
IN OUT
VIDEO
B
IN OUT
ALL ABOUT IMAGE RECOGNITION & PROCESSING
VIDEO PRINTER
VCR
8 channel stand-alone DVMR 2. Installation
32
3. How to get IP for DVMR unit
There is 2 different ways to input IP address and other data into DVMR unit.
The first way is to make DVMR system get IP address from DHCP server automatically. It is only possible in
case DVMR unit is connected to cable modem(dynamic IP), Intranet under DHCP server or IP sharer which
support DHCP. Select “DHCP” in TCP/IP setup to get IP address automatically.
The second way is you get IP address and other data before you connect DVMR unit to network and later
input this IP address and other data into DVMR unit. Except the case you already know IP address assigned
for DVMR unit, get IP address for DVMR unit as following process in the client PC from which you want to
access to DVMR unit via IP network. If you connect DVMR unit to leased line with static IP already known, it is
not necessary to follow following process toget IP information.
a) “ipconfig” or “winipcfg”
Execute “ipconfig” command in the client PC with Windows 2000 and Windows XP, and “winipcfg” command
in the client PC with Windows 98 and ME, and you will get IP informations, that are IP Address, Gateway,
Subnet Mask. Write down those numbers and input into DVMR unit to which you are going to access via IP
network. As far as DVMR is in operation without turning off, it is considered that this IP Address is assigned
just to this DVMR unit. Then, restart the client PC to get different dynamic IP address for client PC after you
get IP information for DVMR unit. Derail procedure to get IP information in different Windows is as follows.
ⓐWindow 2000
First you need to get to the command prompt using the command shell. The best way is from the run menu.
Start--> Run --> and type in Command. Then either hit enter or click OK. At the command prompt, type in
ipconfig. This will pull up the information that you need to find IP Address for DVMR unit.
ⓑWindows XP
If you want to get IP Address for your DVMR in Windows XP, you can run ipconfig in one easy step. Open
Run and type "cmd /k ipconfig" without the quotes. This will open the command prompt and start ipconfig
the easy way. Assign IP Address you get to DVMR unit.
ⓒWindows 98 and ME
To run winipcfg, grab the Run item from the Start menu and type winipcfg into the Open: box. Hit OK (or
RETURN). Those comfortable with DOS can launch it from a DOS prompt.
When winipcfg launches, you'll get a window like this one:
ALL ABOUT IMAGE RECOGNITION & PROCESSING
8 channel stand-alone DVMR 5.Menual for Remote Viewer Software(TCP/IP)