Geneinno TITAN User manual

TITAN
USER MANUAL
V1.0.5
2018.12

I. Users tips 2
II. Product
Overview 3
Titan graphic 3
Connect Titan 4
Bluetooth controller 5
Charge 6
III. APP operation
App main page 7
App operation interface 8
APP system settings 9
APP info 12
APP photo and video 14
IV. Brief Troubleshooting 15
V. Appendixes
Product parameter list 16
Product warranty 17
CONTENT

Packing list：
1.Titan, wireless relay, cable
2.Charger
3.Balancing weight
4.The bluetooth handle
5.Filter (users'choice)
6.User's Manual
Manual：
The contents and pictures of this manual are subject to the actual version and
the latest version. The content is subject to change without prior notice. Please
visit the official website “Download”page for the latest version.
APP:
Android IOS
Attention：
1.It is recommended that the weight Balancing block should not be installed in fresh water,
and the weight Balancing block should be installed in seawater. The installation position
should be adjusted according to the actual balance state of the host machine, whichever is
the best balance that the host machine can achieve.
2.Wireless relay design for low grade waterproofing standards, do not use directly in water.
3.At the beginning of use, it is recommended that the cable be connected to the wireless
relay first, and then to the host machine. The system will be powered on.
4.Please control the speed of movement during use to avoid scratches or equipment
damage caused by collision.
5.After the end of use, please rinse with fresh water and dry , especially keep the insertion
dry.Reduce corrosion of sea water and store in dry ventilation
6.Titan is designed for positive buoyancy. It is recommended to be used in clean water so
as not to stick sediment to affect buoyancy balance.
7.Please connect the Titan to wireless relay before putting it in the water, set the fresh/salt
water according to using environment
I. User tips
Copyright © 2018 GENEINNO All Rights Reserved.

II. Product
Overview：
Titan is a consumer level underwater intelligent robot, equipped with A17/A7 dual-
core CPU, supporting H265, 4K video encoding and decoding.
Equipped with professional deep-sea starlight level 4k camera, front 3000lm led light,
and built-in special image processing DSP,
At the same time, the whole machine adopts industrial-grade waterproof scheme,
with a maximum diving depth of 150m.The maximum speed is 2m/s, 2 high-power
horizontal thrusters and 4 low-power vertical thrusters. The closed-loop control
algorithm can effectively realize 360 degree full-attitude control, underwater
hovering and self-balance.
④signal/charging
port
Titan graphic：
Head
①Camera
②Light
Top
Bottom
⑥Buoyancy
control block
③Thruster
③Thruster
⑤Drainage
port
⑦Extension
port
Wireless relay
Cable
Copyright © 2018 GENEINNO All Rights Reserved.

Connect instructions：
1. Connect device: Insert one end of the wireless relay cable into the socket of the wireless
relay and tighten it with force. Insert the other end into the socket of the host machine and
tighten it with equal force, then complete Titan connection and power on.
2. App connect: when Titan gets to work(about 1 minute after connection), the LED light
on ,Titan will flash twice every several seconds, it means the Titan is ready to connect to
your phone, pad and PC devices, search the Wi-Fi hotspot named GENEINNO_XXXX,
connect your device to it, the default passwords is 88886666, then get to the app control
interface.
3. Operation: Put Titan into the water, you can freely control Titan to rise and dive.Wireless
relay has low grade waterproofing standard. It is recommended to be placed on shore or
on board and fixed to avoid the difficulty of recovery after being dragged into the water by
Titan.
Mobile device：with Android or IOS GeneROV APP installed
Connect Titan
Charger ①Plug
②Adapter
③Charging port
Copyright © 2018 GENEINNO All Rights Reserved.
①
③
Titan
wireless relay
②
④
⑤

Bluetooth controller
1. Connecting：
A: Start up: Turn the left button to the on position, press the HOME for 2 seconds until
the LED1 and LED2 flickering, the controller turns on.
B: Connect: When the controller is turned on, the light flickers, the controller is in the
connecting mode. Open the APP on your device, open the right menu bar, open
Bluetooth controller, tap to search the controller, you can find the BLE device named
GENEINNO-XXXX, tap to connect; when Bluetooth controller connected, the LED1/2 light
stays on.
C. Turn off: Turn the left button to the off position, the controller turns off. When it
turns on for 3 minutes without connect the device, the controller will turn off
automatically; when the Bluetooth is connected for 3 minutes with out operation, the
controller will turn off automatically.
D. Connect position confirm：When it controller is connected successfully via
Bluetooth, open the GeneROV APP, there will be the controller icon indication in the APP
operation interface.
2. Bluetooth controller keys：
A: Confirm for menu and pages, switch for menu of turn on/off；
B: Back for menu and pages, cancel；
X: Gear reduce by one, doesn’t work when it’s in the max third gear；
Y: Gear increase by one, doesn’t work when it’s in the min first gear.;
R: Light down by one, LED out when it’s 0, doesn’t work when it reach it min.
R2: Light up by one, doesn’t work when it reach the max.
R3(Press the right gear vertically): Turn on/off the lock of depth.
L: Start/pause recording ；L2: shot, start/pause burst；
L3: (Press the left gear vertically): Turn on/off the lock of direction；
Stick R: Pop for more page information(Home page), selection move to the right or
current value increase by one(home page)，
Copyright © 2018 GENEINNO All Rights Reserved.

Copyright © 2018 GENEINNO All Rights Reserved.
Charge
1. Titan battery info will be seen at APP operation interface, battery signal light info
will be seen at wireless relay; Please charge Titan when battery is low using standard
charger and plug; charge Titan for 3 hours, wireless relay for 2 hours; signal lights on
charger is red when it’s charging, turn into green when fully charged.
2. Be sure, that there are no water in the plugs,before you start charging.
①How to charge Titan: tighten the plug between charger
and Titan
②How to charge wireless relay: tighten the plug between
charger and wireless relay
X：increase gear
Y：reduce gear
L：Record
L2：Shot
Dive up/down
Direction
control
Stick:
up/down
left/right A：Confirm
B：Quit
R：reduce LED lightness
R2：increase LED lightness
Stick L: Pop for the setting menu(home page), selection move to the left or current
value reduce by one(home page).
Stick U: Focus move up Stick D: Focus move down
Titan
Charger
Wireless Relay
Charge
①
②

III. APP operation
[16]
[15]
APP Main Page
[11]
[12]
[13]
12
3
4
5
6 7 8
：Product type
：Menu (APP update, hardware update, Bluetooth controller, about and help options)
：Titan picture
：Current status
：Current equipment name and entrance
：Device
：Forum
：Underwater City
[1]
[2]
[3]
[4]
[5]
[6]
[7]
[8]
Copyright © 2018 GENEINNO All Rights Reserved.

：Return
：Menu
：Depth
：Up/Down/Left/Right
：Motion mode
：Running Time
：Bluetooth controller
：Temperature
：Delay
：Battery
：Settings
：Shot/Film mode
：Shot/Film
：photos/Videos
：Attitude control
：LED
：3D real-time attitude
：Lock Down Depth
：Motion Switch
：Lock Down Direction
：Restore 0 pitch angle
APP operation interface
APP Operation Interface
5 6 7 8 9 10
1
2
3
4
11
12
13
14
15
161
171
18 19 20 21
[21]
[1]
[2]
[3]
[4]
[5]
[6]
[7]
[8]
[9]
[10]
[11]
[12]
[13]
[14]
[15]
[16]
[17]
[18]
[19]
[20]
Copyright © 2018 GENEINNO All Rights Reserved.

APP System Settings
App consists of camera settings, recording settings, environment settings,
señor settings, mode settings and factory settings
App系统设置界面
1. Camera settings consist of shot settings, live-streaming quality and anti-shake
switchers。
Copyright © 2018 GENEINNO All Rights Reserved.

APP System Settings
live-streaming quality can select 1080P/720P/480P, default 720P
Shot settings can select single shot or burst shot, burst shot can shot maximum
99 pics, and max interval is 99 seconds
Copyright © 2018 GENEINNO All Rights Reserved.

APP System Settings
2. Recording settings consist of resolution, format, file time length, watermark
switchers
Resolution: 3840*2140/1920*1080
Format: H265/H264, H264/H265 will be saved as MP4.
File time length: range from 0-30, unsegmented saving when time length is 0
Watermark switchers: add depth, temperature, time and other info on photo/video
3. Environment settings can select salt water or fresh water, salt water or fresh
water has effect on depth accuracy.
Search BLE used to connect bluetooth controller.(该页面已经修改)
Copyright © 2018 GENEINNO All Rights Reserved.

APP info
The information consists of internal storage information, battery information, motor
speed values, and version information. As shown:
1. The internal storage information could indicate the usage of internal SD card
storage occupation and vacant space
Copyright © 2018 GENEINNO All Rights Reserved.

APP info
2.Battery information consists of current, voltage, power, water pressure, internal
humidity, and internal temperature data.
3. The motor speed value information can display the current speed of each motor
in real time.
Copyright © 2018 GENEINNO All Rights Reserved.

App info
4. The version information shows the current device firmware version information.
App photo and video:
Divided into remote ROV directory and local directory, long press the selected
photo to save, delete and select all.
Copyright © 2018 GENEINNO All Rights Reserved.

Copyright © 2018 GENEINNO All Rights Reserved.
Export photos and videos to the computer
1. PC
Windows:
First, use a laptop to connect to the device WIFI, and then enter \\192.168.8.8 in the
start-run to open the device file system, Photos is the photo storage folder, Videos is the
video storage folder, and when opened, you can copy, cut, delete or copy files from the
computer.
Mac:
The Mac connects to Titan WIFI, and then opens the Finder application on the Mac.
After opening the application, press the command+K key on the keyboard and enter
SMB :// 192.168.8.8 in the server address.
2. Android
First, use the tablet or mobile phone to connect the device. After successful
connection, enter the photo video page, select the remote ROV directory, open and
select the photo or video you want to open for download.
IV. Brief Troubleshooting1. Cannot search for GENEINNO WIFI hotspot after
cable connection:
Check if the cable connection is tight.
Check the wireless relay battery indicator, if the battery is low.
2. Connected to the GENEINNO WIFI hotspot, but can't see the real-time picture, can't
control:
Check if Titan LED flashes, such as flashing 3, 4 or 5 times, the internal fault of the host,
please contact after-sales customer service.
When LED light does not flash, please confirm whether the battery is low, try to use it
again after charging; still can not be used after charging, please contact after-sales
customer service.
3. Motor obstruction
Please power off first, manually remove the obstacles, and then turn on the power
again. For more information, please open the APP for help information.

IV. Appendix
Drone
Weight 9.7Ibs (4.4kg)
Dimension 15.35×13.66×6.5 inch
390×347×165 mm
Depth 492.15ft (150m)
Speed 6.6ft/s (2m/s)
Degrees of Freedom Forward/back, rise/fall, turn left/right
Thruster 6
Camera
Image Sensor 1/2.5 inches SONY CMOS
Video Resolution 4K
Video Format MP4(H264/H265)
Photo Fomat JPEG
FOV 160°
Lumen 1500lm×2
Micro SD 32G
Tether
Strength 500N(50KG)
Length 164ft/328.08ft/492ft (50m/100m/150m)
Diameter 4.5mm/0.18 inch
Sensors
IMU 6 axis gyro & accelerometer+3 axis Compass
Depth Sensor +/- 0.2m
Temp. Sensor +/-0.5℃
Battery
Chemical Lithium
Capacity 10.8V/9000mAh/97.2Wh（Titan）
10.8V/3200mAh/34.56Wh (Wireless Relay)
Run time 4 hours(Titan)/6 hours(wireless relay)
Charge time 3 hours(Titan)/3 hours(wireless relay)
App
Platform IOS 9.0 and Android 5.0
Product parameter list
Copyright © 2018 GENEINNO All Rights Reserved.

Product warranty
1. If the product fails in use, please contact our after-sales service as soon as possible
,so as not to delay your use and maintenance.
2. This product has 1-year whole machine tracking service from the date of purchase by
the customer. The company is responsible for product repair and replacement caused
by the equipment itself during normal use. Damage of equipment shell due to impact
or dissembling by user will not enjoy free maintenance.
3. If maintenance exceeds the warranty period, maintenance fee will be charged. (repair
fee + component fee)
4. For after-sale service, please visit our official website for instructions:
Address: www.geneinno.com
or you could email us directly to our after-sale support:
Email: [email protected]
We welcome your valuable comments on our product quality and after-sale service.
Copyright © 2018 GENEINNO All Rights Reserved.

深圳市吉影科技有限公司
www.geneinno.com
TITAN USER MANUAL
Facebook YouTube
Wechat Weibo