General International 50-760 M1 Parts list manual

SETUP & OPERATION MANUAL
Version #2_Revision #1 - February 2016
© Copyright General International
16” RADIAL ARM SAW
MODEL
#50-760 M1
FEATURES
Industrial rated quality and versatile design
allows for standard crosscuts, as well as bevels,
miters, and head swivels for rip cutting applica-
tions.
Powerful 3 HP 220V single phase (M1) or 4 HP
220V 3-phase (M2) motor.
Cast-iron frame, heavy steel column, and sturdy
easy to assemble all-steel stand for perfect
alignment and stability.
Precision adjustable indexing with positive stops
at 90º, 45º for accurate miter and rip cuts.
Blade guard with anti-kickback attachment and
splitter.
Magnetic switch with overload protection and a
lock-out key to prevent unauthorized use.
Automatic mechanical brake stops the blade in
seconds upon shutdown.
Dual 4” dust ports above the table, and a 2” dust
port on the rear of the blade guard.
Adjustable tension cutterhead / carriage return
spring to smoothly retract the motor and car-
riage back to the start position.
1” arbor included.
SPECIFICATIONS
• Blade diameter
16” (406 mm)
• Arbor diameter
1” (25 mm)
• Maximum depth of cut at 90°
4 7/8” (124 mm)
• Maximum depth of cut at 45°
2 1/2” (65 mm)
• Maximum crosscut capacity (with 16” blade)
24” (609 mm)
• Maximum rip capacity
38” (965 mm)
• Dado capacity
1” (25 mm)
• Table height
32” (813 mm)
• Table size
39 3/4” x 48” (1010 x 1220 mm)
• Overall dimensions (l x w x h)
56 5/8” x 48” x 67 7/16” (1439 x 1220 x 1713 mm)
• Motor M1
3 HP, 220 V, 12.5 A
• Motor M2
4 HP, 220 V, 3 ph, 10.5 A
• Weight (shipping / net)
799 lbs (363 kg) / 572 lbs (260 kg)

GENERAL® INTERNATIONAL
8360 Champ-d’Eau, Montreal (Quebec) Canada H1P 1Y3
Telephone [phone] • Fax [phone] • www.general.ca
THANK YOU
for choosing this General® International model 50-760 16”radial
arm saw. This radial arm saw has been carefully tested and inspected before shipment and if
properly used and maintained, will provide you with years of reliable service. For your safety,
as well as to ensure optimum performance and trouble-free operation, and to get the most
from your investment, please take the time to read this manual before assembling, installing
and operating the unit.
The manual’s purpose is to familiarize you with the safe operation, basic function, and features
of this radial arm saw as well as the set-up, maintenance and identification of its parts and
components. This manual is not intended as a substitute for formal woodworking instruction,
nor to offer the user instruction in the craft of woodworking. If you are not sure about the safety
of performing a certain operation or procedure, do not proceed until you can confirm, from
knowledgeable and qualified sources, that it is safe to do so.
Once you’ve read through these instructions, keep this manual handy for future reference.
DISCLAIMER: The information and specifications
in this manual pertain to the unit as it was supplied
from the factory at the time of printing. Because we
are committed to making constant improvements,
General® International reserves the right to make
changes to components, parts or features of this
unit as deemed necessary, without prior notice and
without obligation to install any such changes on
previously delivered units. Reasonable care is taken
at the factory to ensure that the specifications and
information in this manual corresponds with that of the
unit with which it was supplied. However, special orders
and ”after factory” modifications may render some
or all information in this manual inapplicable to your
machine. Further, as several generations of this model
radial arm saw and several versions of this manual may
be in circulation, if you own an earlier or later version of
this unit, this manual may not depict your unit exactly. If
you have any doubts or questions contact your retailer
or our support line with the model and serial number of
your unit for clarification.

GENERAL®INTERNATIONAL WARRANTY
All component parts of General®International and Excalibur by General International®products
are carefully inspected during all stages of production and each unit is thoroughly inspected upon
completion of assembly.
Limited Lifetime Warranty
Because of our commitment to quality and customer satisfaction, General®International agrees to
repair or replace any part or component which upon examination, proves to be defective in either
workmanship or material to the original purchaser for the life of the tool. However, the Limited Lifetime
Warranty does not cover any product used for professional or commercial production purposes nor
for industrial or educational applications. Such cases are covered by our Standard 2-year Limited
Warranty only. The Limited Lifetime Warranty is also subject to the ”Conditions and Exceptions” as listed
below.
Standard 2-Year Limited Warranty
All products not covered by our lifetime warranty including products used in commercial, industrial
and educational applications are warranted for a period of 2 years (24 months) from the date of
purchase. General® International agrees to repair or replace any part or component which upon
examination, proves to be defective in either workmanship or material to the original purchaser during
this 2-year warranty period, subject to the ”conditions and exceptions” as listed below.
To file a Claim
To file a claim under our Standard 2-year Limited Warranty or under our Limited Lifetime Warranty,
all defective parts, components or machinery must be returned freight or postage prepaid to
General® International, or to a nearby distributor, repair center or other location designated by
General® International. For further details call our service department at 1-888-949-1161 or your local
distributor for assistance when filing your claim.
Along with the return of the product being claimed for warranty, a copy of the original proof of
purchase and a ”letter of claim” must be included (a warranty claim form can also be used and can
be obtained, upon request, from General®International or an authorized distributor) clearly stating the
model and serial number of the unit (if applicable) and including an explanation of the complaint or
presumed defect in material or workmanship.
CONDITIONS AND EXCEPTIONS:
This coverage is extended to the original purchaser only. Prior warranty registration is not required but
documented proof of purchase i.e. a copy of original sales invoice or receipt showing the date and
location of the purchase as well as the purchase price paid, must be provided at the time of claim.
Warranty does not include failures, breakage or defects deemed after inspection by
General®International to have been directly or indirectly caused by or resulting from; improper use,
or lack of or improper maintenance, misuse or abuse, negligence, accidents, damage in handling or
transport, or normal wear and tear of any generally considered consumable parts or components.
Repairs made without the written consent of General® International will void all warranty.

TABLE OF CONTENTS
Rules for safe operation..................................................................................................... 5
Electrical requirements ...................................................................................................... 6
Identification of main parts and components .................................................................. 7
Unpacking.......................................................................................................................... 8
Basic functions................................................................................................................... 8
Placement within the shop ................................................................................................ 9
Assembly instructions ................................................................................................... 9-14
Installing the handwheel handle...................................................................................................................... 9
Installing the blade........................................................................................................................................... 10
Installing the control box ................................................................................................................................. 12
Installing the dust port and the dust hose ..................................................................................................... 12
Installing the riving knife .................................................................................................................................. 14
Connecting the cutter head to the return spring ......................................................................................... 14
Basic adjustments and controls ................................................................................. 14-19
Connecting to a power source....................................................................................................................... 14
Main On/Off magnetic switch ........................................................................................................................ 15
Overload protection......................................................................................................................................... 15
Adjusting the cutter head height.................................................................................................................... 15
Positioning the cutter head on the arm......................................................................................................... 16
Positioning the cutter head for miter cuts ...................................................................................................... 16
Pivoting the cutter head for ripping ............................................................................................................... 16
Pivoting the cutter head for bevel cross cutting ........................................................................................... 17
Adjusting the cutter head stop........................................................................................................................ 17
Adjusting the return spring tension ................................................................................................................. 18
Adjusting the anti-kickback fingers ................................................................................................................ 18
Positioning the fence........................................................................................................................................ 18
Connecting to a dust collector....................................................................................................................... 19
Operating Instructions ................................................................................................ 19-23
Checklist before starting .................................................................................................................................. 19
Cutting the kerf in the work table.................................................................................................................... 19
Types of cuts ...................................................................................................................................................... 21
Maintenance............................................................................................................... 23-29
Adjusting the work table parallel to the cutter head ................................................................................... 23
Squaring the blade to the table ..................................................................................................................... 25
Squaring the blade to the fence .................................................................................................................... 26
Adjusting the graduated scale for inboard ripping..................................................................................... 27
Cutter head bearing adjustment ................................................................................................................... 28
Adjusting the base............................................................................................................................................ 28
Adjusting the cutter head arm........................................................................................................................ 29
Parts list & diagrams................................................................................................... 30-38
Contact information ........................................................................................................ 40

5
RULES FOR SAFE OPERATION
1. Do not operate the saw when tired, distracted, or un-
der the effects of drugs, alcohol or any medication
that impairs reflexes or alertness.
2. The work area should be well lit, clean and free
of debris.
3. Keep children and visitors at a safe distance when
the saw is in operation; do not permit them to ope-
rate the saw.
4. Childproof and tamper proof your shop and all ma-
chinery with locks, master electrical switches and
switch keys,to prevent unauthorized or unsupervised
use.
5. STAY ALERT! Give your work your undivided attention.
Even a momentary distraction can lead to serious
injury.
6. Fine particulate dust is a carcinogen that can be
hazardous to health. Work in a well-ventilated area
and whenever possible use a dust collector and
wear eye, ear and respiratory protection devices.
7. Do not wear loose clothing, gloves, bracelets, neck-
laces or other jewelry while the saw is in operation.
Wear protective hair covering to contain long hair
and wear non-slip footwear.
8. Be sure that adjusting wrenches, tools, drinks and
other clutter are removed from the machine and/or
the table surface before operating.
9. Keep hands well away from the blade and all
moving parts. Use a brush, not hands, to clear away
chips and dust.
10. Be sure that the blade is securely installed and in the
proper cutting direction before operation.
11. Be sure the blade has gained full operating speed
before beginning to cut.
12. Always use a clean, properly sharpened blade. Dir-
ty or dull blades are unsafe and can lead to
accidents.
13. Do not push or force stock into the blade. The saw
will perform better and more safely when working at
the rate for which it was designed.
14. To minimize risk of injury in the event of workpiece
kickback, never stand directly in-line with the blade
or in the potential kickback path of the workpiece.
15. Avoid working from awkward or off balance posi-
tions. Do not overreach while cutting; keep both feet
on floor. Use outfeed support or have an assistant
help when cutting long material.
16. Keep blade guards in place and in working or-
der. If a guard must be removed for maintenance or
cleaning, be sure it is properly re-attached before
using the tool again.
17. Never leave the machine running with the power on
when not in operation.
18. Use of parts and accessories NOT recommended
by General®International may result in equipment
malfunction or risk of injury.
19. Never stand on machinery. Serious injury could
result if the tool is tipped over or if the blade is unin-
tentionally contacted.
20. Always disconnect tool from power before servicing
or changing accessories such as blades, or before
performing any maintenance, cleaning or adjust-
ments, or if the machine will be left unattended.
21. Make sure that switch is in ”OFF”position before plug-
ging in the power cord.
22. Make sure the tool is properly grounded. If equip-
ped with a 3-prong plug it should be used with a
three-pole receptacle. Never remove the third prong.
23. Do not use this saw for any purpose other than its
intended use. If used for other purposes,
General® International disclaims any real or im-
plied warranty and holds itself harmless for any in-
jury, which may result from that use.
To help ensure safe operation, please take a moment to learn the machine’s applications and limitations,
as well as potential hazards. General®International disclaims any real or implied warranty and holds itself
harmless for any injury that may result from the improper use of its equipment.

ELECTRICAL REQUIREMENTS
6
ABC
BEFORE CONNECTING THE MACHINE TO THE POWER SOURCE, VERIFY THAT THE VOLTAGE OF YOUR POWER
SUPPLY CORRESPONDS WITH THE VOLTAGE SPECIFIED ON THE MOTOR I.D. NAMEPLATE. A POWER SOURCE
WITH GREATER VOLTAGE THAN NEEDED CAN RESULT IN SERIOUS INJURY TO THE USER AS WELL AS DAMAGE
TO THE MACHINE. IF IN DOUBT, CONTACT A QUALIFIED ELECTRICIAN BEFORE CONNECTING TO THE POWER
SOURCE.
THIS TOOL IS FOR INDOOR USE ONLY. DO NOT EXPOSE TO RAIN OR USE IN WET OR DAMP LOCATIONS.
ELECTRICAL CONNECTIONS
Both a manual circuit breaker (or similar device) as well
as an electrical plug (similar to the one shown) are re-
commended and SHOULD BE INSTALLED BY A QUALIFIED
ELECTRICIAN.
Use locally approved wire Athat includes a separate
grounding wire and a 3 prong grounding type plug B
with a matching receptacle C.
GROUNDING INSTRUCTIONS
In the event of an electrical malfunction or short circuit, grounding reduces the risk of electric shock to the opera-
tor. The motor of the ”M1” model of this machine is wired for 220 V single phase operation. As with many stationary
industrial type machines, because each installation situation is unique, this machine is supplied without a power
cord or plug.The installation of an appropriate power cord and plug must be performed by a qualified electrician.
The machine must be connected to an electrical source using a power cord that has a grounding wire, which
must also be properly connected to the grounding prong on the plug. The outlet must be properly installed and
grounded and all electrical connections must be made in accordance with all local codes and regulations.
CIRCUIT CAPACITY
Make sure that the wires in your circuit are capable of handling the amperage draw from your machine, as well as
any other machines that could be operating on the same circuit. If you are unsure, consult a qualified electrician.
If the circuit breaker trips or the fuse blows regularly, your machine may be operating on a circuit that is close to its
amperage draw capacity. However, if an unusual amperage draw does not exist and a power failure still occurs,
contact a qualified technician or our service department.
EXTENSION CORDS
The use of an extension cord is not generally recommended for 220 V equipment. If you find it necessary, use
only 3-wire extension cords that have 3-prong grounding plug and a matching 3-pole receptacle that accepts
the tool’s plug. Repair or replace a damaged extension cord or plug immediately. Make sure the cord rating is
suitable for the amperage listed on the motor I.D. plate. An undersized cord will cause a drop in line voltage result-
ing in loss of power and overheating. The accompanying chart shows the correct size extension cord to be used
based on cord length and motor I.D. plate amp rating. If in doubt, use the next heavier gauge.
TABLE - MINIMUM GAUGE FOR CORD
EXTENSION CORD LENGTH
AMPERES 50 feet 100 feet 200 feet 300 feet
< 5 18 16 16 14
6 to 10 18 16 14 12
10 to 12 16 16 14 12
12 to 16 14 12 *NR v
*NR = Not Recommended
Note: Voltage requirements and amperage draw for M2 3-phase motor may not be fully
described in this manual. For complete electrical requirements refer to the motor I.D. name
plate on the machine. If in doubt consult a licensed qualified electrician before proceeding.

7
IDENTIFICATION OF MAIN PARTS AND COMPONENTS
A. STAND
B. WORK TABLE
C. DUST PORT SUPPORT
D. ADJUSTABLE TENSION RETURN SPRING
E. BLADE HEIGHT ADJUSTMENT HANDWHEEL
F. DUST HOSE
G. ARM
H. ON/OFF SWITCH
I. SEE-THROUGH BLADE COVER
J. ANTI-KICKBACK FINGERS
B
F
H
J
G
C
A
D
E
I

8
UNPACKING
Carefully unpack and remove the unit and its components from the box and check for missing or damaged items
as per the list of contents below.
NOTE: PLEASE REPORT ANY DAMAGED OR MISSING ITEMS TO YOUR GENERAL® INTERNATIONAL DISTRIBUTOR IMMEDIATELY.
BASIC FUNCTIONS
This 16”radial arm saw is designed for multipurpose cutting of solid wood, as well as manufactured wood materials
and other wood based by-products. This saw is not designed for cutting metals nor for cutting any materials other
than wood or wood based stock.
This versatile unit offers a crosscutting capacity of 24” and uses maximum 16" (406 mm) diameter blades having a
center hole bore diameter of 1". The maximum stock thickness cutting capacity of this saw is 4 7/8” with the blade
set 90 degrees to the table. The blade can be tilted up to 45 degrees for bevel cuts to a maximum stock thickness
of 2 1/2". The 50-760 is also designed to perform miter cuts and compound (beveled) miters and has a dado cut-
ting capacity of 1”.
LIST OF CONTENTS QTY
A. DUST PORT SUPPORT................................................................ 1
B. RIVING KNIFE........................................................................... 1
C. HANDWHEEL HANDLE.............................................................. 1
D. HOSE CLAMP........................................................................... 2
E. DUST HOSE ............................................................................... 1
F. BLADE....................................................................................... 1
G. DUST PORT ............................................................................... 2
H. ARBOR WRENCH ..................................................................... 1
I. 11-13, 12-14, 17-19, 21-23 MM WRENCHES............................. 1
J. 5, 6, 8 MM ALLEN KEYS............................................................ 1
K. REVERSIBLE SCREWDRIVER (FLAT/PHILLIPS) .......................... 1
ADDITIONAL REQUIREMENTS FOR SET UP
A. 4 MM ALLEN KEY
B. 10 MM WRENCH
C. STRAIGHT EDGE
D. MACHINISTS SQUARE
E. MEASURING CALIPERS
A
F
GIJ
K
E
D
C
B
H

PLACEMENT WITHIN THE SHOP / SAFETY ZONE
9
THIS RADIAL ARM SAW MODEL 50-760 IS HEAVY. DO NOT OVER-EXERT. A HOIST OR FORKLIFT WITH STRAPS SHOULD
BE USED TO LIFT THIS MACHINE. TO LIMIT THE RISK OF SERIOUS INJURY OR DAMAGE TO THE MACHINE, ANY EQUIP-
MENT USED TO LIFT THIS MACHINE SHOULD HAVE A RATED CAPACITY IN EXCESS OF 572 LBS (260 KG).
ASSEMBLY INSTRUCTIONS
INSTALLING THE HANDWHEEL HANDLE
BEFORE ASSEMBLING, MAKE SURE THAT THE SWITCH IS IN THE ”OFF” POSITION AND THAT THE POWER CORD IS
UNPLUGGED. DO NOT PLUG IN OR TURN ON THE MACHINE UNTIL YOU HAVE COMPLETED THE ASSEMBLY AND
INSTALLATION STEPS DESCRIBED IN THIS SECTION OF THE MANUAL.
48"
32"
58"
68"
PLACEMENT WITHIN THE SHOP
This machine should be installed and operated only on a
solid, flat and stable floor that is able to support the weight
of the machine (572 lbs - 260 kg) and the operator. Using
the dimensions shown as a guideline, plan for placement
within your shop that will allow the operator to work unen-
cumbered and unobstructed by foot traffic (either pass-
ing shop visitors or other shop workers) or other tools or
machinery.
ESTABLISHING A SAFETY ZONE
For shops with frequent visitors or multiple operators, it is
advisable to establish a safety zone around shop machin-
ery. A clearly defined ”no-go” zone on the floor around
each machine can help avoid accidents that could
cause injury to either the operator or the shop visitor.
It is advisable to take a few moments to either paint (using
non-slip paint) or using tape, define on the floor the limits
or perimeter of each machines safety zone. Take steps to
ensure that all operators and shop visitors are aware that
these areas are off limits whenever a machine is running
for everyone but the individual operating the unit.
Note: For your convenience this saw is shipped from the factory partially assembled and requires only minimal assembly
and set up before being put into service.
1. Thread the handle into the handwheel. 2. Secure the handle by tightening it with a 12 mm
wrench.

10
BEFORE ASSEMBLING, MAKE SURE THAT THE SWITCH IS IN THE ”OFF” POSITION AND THAT THE POWER CORD IS
UNPLUGGED. DO NOT PLUG IN OR TURN ON THE MACHINE UNTIL YOU HAVE COMPLETED THE ASSEMBLY AND
INSTALLATION STEPS DESCRIBED IN THIS SECTION OF THE MANUAL.
INSTALLING THE BLADE
There are a variety of different types of blades on the market to suit various cutting applications. Your results
may vary based on usage, experience and personal preference. Ask your local tool dealer for suggestions
for 16” X 1” (406 X 25 mm) blades.
5. Loosen the 2 screws Dusing a 6 mm Allen key. 6. Remove the blade cover.
1. Unlock the cutter head by turning the handle Ato
the left.
2. While lowering handle B, rotate the cutter head the
right as shown.
3. Release handle Bonce the cutter head is posi-
tioned in front of you.
4. Loosen lock lever Cto position the cutter head at
the end of the arm, then retighten the lever to lock
the cutter head in position.
AB
D
C

BEFORE ASSEMBLING, MAKE SURE THAT THE SWITCH IS IN THE ”OFF” POSITION AND THAT THE POWER CORD IS
UNPLUGGED. DO NOT PLUG IN OR TURN ON THE MACHINE UNTIL YOU HAVE COMPLETED THE ASSEMBLY AND
INSTALLATION STEPS DESCRIBED IN THIS SECTION OF THE MANUAL.
11
INSTALLING THE BLADE (CONTINUED)
10. Re-install the flange and then the arbor nut. 11. Using an 8 mm Allen key to immobilise the arbor,
secure the blade by turning the arbor nut coun-
terclockwise with the arbor wrench. Re-install the
blade cover before starting the machine.
7. Remove the arbor nut by turning it clockwise. 8. Remove the flange.
9. Install the blade onto the arbor. Note: Before moving forward, make sure the blade teeth
are pointing to the right.

BEFORE ASSEMBLING, MAKE SURE THAT THE SWITCH IS IN THE ”OFF” POSITION AND THAT THE POWER CORD IS
UNPLUGGED. DO NOT PLUG IN OR TURN ON THE MACHINE UNTIL YOU HAVE COMPLETED THE ASSEMBLY AND
INSTALLATION STEPS DESCRIBED IN THIS SECTION OF THE MANUAL.
12
INSTALLING THE CONTROL BOX
3. Align the support mounting holes with the corre-
sponding holes in the machine, then secure the
support using the four bolts and the washers.
4. Slide the hose clamp onto the end of the dust hose.
1. Remove the 2 screws at the back of the machine
using a Phillips screwdriver.
2. Align the control box mounting holes with the cor-
responding holes in the machine, then secure the
box to the stand using the two screws.
INSTALLING THE DUST PORT SUPPORT AND THE DUST HOSE
1. Remove the four bolts and washers using a 13 mm
wrench.
2. Set the dust port support on the machine as shown.

13
BEFORE ASSEMBLING, MAKE SURE THAT THE SWITCH IS IN THE ”OFF” POSITION AND THAT THE POWER CORD IS
UNPLUGGED. DO NOT PLUG IN OR TURN ON THE MACHINE UNTIL YOU HAVE COMPLETED THE ASSEMBLY AND
INSTALLATION STEPS DESCRIBED IN THIS SECTION OF THE MANUAL.
INSTALLING THE DUST PORT SUPPORT AND THE DUST HOSE (CONTINUED)
5. Slide the hose end onto the outlet, then secure it
by tightening the hose clamp with a Phillips screw-
driver.
9. Secure the two dust ports to the support with the 8
screws.
10. Slide the hose end onto the blade cover outlet,
then secure the hose clamp using a Phillips screw-
driver.
6. Set the hose holder arm in the vertical position,
then slide the hose through the hose holder.
8. Remove the 8 screws using a Phillips screwdriver.7. Secure the hose holder in the vertical position by
tightening the cap screw with a 5 mm Allen key.

INSTALLING THE RIVING KNIFE
BEFORE ASSEMBLING, MAKE SURE THAT THE SWITCH IS IN THE ”OFF” POSITION AND THAT THE POWER CORD IS
UNPLUGGED. DO NOT PLUG IN OR TURN ON THE MACHINE UNTIL YOU HAVE COMPLETED THE ASSEMBLY AND
INSTALLATION STEPS DESCRIBED IN THIS SECTION OF THE MANUAL.
1. Remove the two screws and washers located in
the blade cover using a 5 mm Allen key.
2. Secure the riving knife Ato the blade cover with
the screws and washers.
CONNECTING THE CUTTER HEAD TO THE RETURN SPRING
SWITCH OFF
TO AVOID UNEXPECTED OR UN-
INTENTIONAL START-UP, MAKE
SURE THAT THE POWER SWITCH
IS IN THE OFF POSITION BEFORE
CONNECTING TO A POWER
SOURCE.
BASIC ADJUSTMENTS & CONTROLS
TO REDUCE THE RISK OF SHOCK OR FIRE DO NOT OPERATE THE UNIT WITH A DAMAGED POWER CORD OR PLUG. RE-
PLACE DAMAGED CORD OR PLUG IMMEDIATELY. TO AVOID UNEXPECTED OR UNINTENTIONAL START-UP, MAKE SURE
THE POWER SWITCH IS IN THE OFF POSITION BEFORE CONNECTING TO A POWER SOURCE.
CONNECTING TO A POWER SOURCE
Once the assembly steps have been completed, plug
the power cord into an appropriate outlet.
Refer back to the section entitled ”Electrical Require-
ments” and make sure all requirements and grounding
instructions are followed.
When cutting operations have been completed, un-
plug the saw from the power source.
1. Position the cutter head close to the column and
pull on the return spring cable.
2. Connect the cutter head by installing the cable as
shown.
Note: Disconnect the cutter head for ripping.
A
14

MAKE SURE THE MACHINE HAS BEEN TURNED OFF AND UNPLUGGED FROM THE POWER SOURCE BEFORE PERFORM-
ING ANY MAINTENANCE OR ADJUSTMENTS.
OVERLOAD PROTECTION
This machine is equipped with an overload protection feature. To prevent an electrical overload from damaging
the motor, in the event of a spike in line voltage or amperage draw, the internal electronic protection system will
automatically cut off power to the motor.
To reset the overload protection, proceed as follows:
1. Unplug the machine from the power source. Loos-
en the two screws Dwith a Phillips screwdriver and
then remove the control box cover.
2. To reset the overload protection, press button E. Re-
install the cover before re-starting the machine.
D
E
MAIN ON/OFF MAGNETIC SWITCH
This machine is equipped with a magnetic safety switch
designed to protect the unit and the user from power
surges, power outages and unwanted or unintentional
start-up.
The electrical box located in the back of the machine is
equipped with a safety lock-out switch with removable
key. The machine can only be started by unlocking the
button with the key and turning the button Ato the ON
position.
Note: When the machine is not in use, remove the key and
store it in a safe place.
To start the saw, press the button B. To stop the saw, press
button C. Once button Chas been pressed, the ma-
chine can only be started by turning button Cto the right.
Note: This bandsaw is also equipped with a motor brake. This device allows for immobilization of the blade after 6 sec-
onds - when not loaded.
AB
C
ADJUSTING THE CUTTER HEAD HEIGHT
1. Loosen lock lever F.2. Turn the handwheel to set the cutter head to the
desired height, then retighten the lock lever to lock
the cutter head in position.
F
15

MAKE SURE THE MACHINE HAS BEEN TURNED OFF AND UNPLUGGED FROM THE POWER SOURCE BEFORE PERFORM-
ING ANY MAINTENANCE OR ADJUSTMENTS.
POSITIONING THE CUTTER HEAD ON THE ARM
1. Loosen the lock lever A.2. Slide the cutter head to the desired position on the
arm and then retighten lever A.
A
POSITIONING THE CUTTER HEAD FOR MITER CUTS
1. Loosen lock lever B, then unlock the arm by lifting
lock lever C.
2. Using the graduated scale D, position the arm to
the desired angle, then retighten lock lever B.
Note: To position the saw at 45º, lock the lever C into the
groove in the column.
BC
D
PIVOTING THE CUTTER HEAD FOR RIPPING
1. Unplug the machine from the power source. Dis-
connect the cutter head from the return spring
and then unlock the cutter head by turning lever Eto
the left.
2. While lowering lever Fpivot the cutter head to the
right or to the left to the desired position. Lock the
cutter in position by tightening the lever E.
Note: Once it is released, the spring loaded lever F pin will
click into the ripping position.
EF
16

MAKE SURE THE MACHINE HAS BEEN TURNED OFF AND UNPLUGGED FROM THE POWER SOURCE BEFORE PERFORM-
ING ANY MAINTENANCE OR ADJUSTMENTS.
PIVOTING THE CUTTER HEAD FOR BEVEL CROSS CUTTING
1. Unplug the machine from the power source. Dis-
connect the cutter head from the return spring.
Raise the cutter head. Loosen lock lever A, then
pull back the lock knob B.
2. Using the graduated scale Cas a reference, pivot the
cutter head to one of the standard pre-set angles.
Note: Once it is released, the spring loaded lever B pin will
click into position.
A
B
ADJUSTING THE CUTTER HEAD STOP
This saw is equipped with an adjustable workpiece stop to limit cutter head travel when dadoing or beveling to pre-
vent the blade from touching the frame. To reduce the risk of damage and injury, it is imperative that this stop
is correctly adjusted according to the instructions in this manual and on the machine before using the saw.
The workpiece stop must be adjusted as follows:
When dadoing, loosen the lock knob Dand position
the stop in the dadoing position as shown. Retighten the
lock knob D.
When beveling, loosen lock knob Dand position the
stop in the beveling position as shown. Retighten the
lock knob D.
C
CLOSE-UP
CLOSE-UP
DADOING BEVELING
CUTTER HEAD STOP
RAINURAGE BISEAU
BUTÉE DE TÊTE DE COUPE
DADOING BEVELING
CUTTER HEAD STOP
RAINURAGE BISEAU
BUTÉE DE TÊTE DE COUPE
D
D
17

18
MAKE SURE THE MACHINE HAS BEEN TURNED OFF AND UNPLUGGED FROM THE POWER SOURCE BEFORE PERFORM-
ING ANY MAINTENANCE OR ADJUSTMENTS.
ADJUSTING THE RETURN SPRING TENSION
To increase return spring tension, push up on lever A
while turning knob Bcounterclockwise.
To decrease tension, push up lever Bwhile turning A
clockwise.
A
B
POSITIONING THE FENCE
1. To reposition the fence Eon the table, loosen the
clamps Fand re-install the fence on Gor Has
needed. Retighten the two clamps.
Note: To reduce muscle fatigue during repetitive cross cut-
tings, install the fence closer to the front edge of the table
as shown.
F
E
GH
TO PREVENT THE SAW “KERF” FROM CLOSING AND BINDING THE BLADE, WHICH CAN OVERLOAD AND/OR STALL
THE MOTOR OR CAUSE THE BLADE TO LIFT AND EJECT THE WORKPIECE TOWARDS THE FRONT OF THE SAW AT VERY
HIGH SPEEDS, ALWAYS USE THE ANTI-KICKBACK FINGERS AND SPLITTER/RIVING DISC.
ADJUSTING THE ANTI-KICKBACK FINGERS
2. Loosen knob Cand place the riving disc Dinside
the saw kerf making sure that the fingers rest on the
workpiece. Retighten knob Cand continue saw-
ing the workpiece.
1. Start ripping the workpiece until the saw kerf reach-
es the anti-kickback fingers, then stop the machine
and wait for the blade to come to a complete stop.
D
C

19
CUTTING THE KERF IN THE WORK TABLE
CHECKLIST BEFORE STARTING
OPERATING INSTRUCTIONS
VERIFY ALL CHECK POINTS BEFORE STARTING. FAILURE TO COMPLY CAN RESULT IN SERIOUS INJURIES.
1. Make sure you and any assistants are wearing safe and appropriate workshop attire.
2. To reduce the risk of damage to the machine, as well as potential for personal injury, after initial set-up as well
as before each use, make sure that everything is securely installed and that all fasteners and moving parts on
this machine are locked in place before starting the machine.
3. Make sure to have on safety glasses as well as hearing or/and respiratory protection at all times when using the
machine.
4. Use only recommended parts and accessories. The use of parts or accessories NOT recommended by
GENERAL® INTERNATIONAL may result in a risk of injury or damage to the machine.
5.
Be sure that adjusting wrenches, tools, drinks and other clutter are removed from the machine and/or the
table surface before operating.
This saw comes with both a sacrificial work table and fence. Before putting the machine into service, a partial kerf
cut of approx 1/16" deep is needed in the fence and the table.
To cut the kerf proceed as follows:
1. Loosen the two fence clamps located on the back
of the table.
2. Install the fence in the position furthest from the
column as shown, then tighten the fence clamps
to secure everything in place..
CONNECTING TO A DUST COLLECTOR
Dual 4” dust ports are provided to accommodate con-
nection to a dust collector (not included).
Be sure to use appropriate sized hose and fittings (not
included). Check that all connections are sealed tight-
ly to help minimize airborne dust.
If you do not already own a dust collection system
consider contacting your General® International dis-
tributor for information on our complete line of dust
collection systems and accessories or visit our Web
Site at www.general.ca.
ALWAYS TURN ON THE DUST COLLECTOR BEFORE STARTING THE SAW AND ALWAYS STOP THE SAW BEFORE TURNING OFF
THE DUST COLLECTOR.

20
MAKE SURE THE MACHINE HAS BEEN TURNED OFF AND UNPLUGGED FROM THE POWER SOURCE BEFORE PERFORM-
ING ANY MAINTENANCE OR ADJUSTMENTS.
CUTTING THE KERF IN THE WORK TABLE (CONTINUED)
3. Loosen the cutter head lock lever. 4. Position the cutter head at the end of the arm, then
retighten the lever to lock the cutter head in position.
7. Turn the saw off by pressing the stop button, then
wait for the blade to stop.Measure the depth of the
kerf. If needed, repeat the previous step until the
required depth is reached. Do not adjust the cutter
head height any further.
8. Turn the saw on then push the cutter head forward
to cut the kerf in the table and the fence.
Note: The user also needs to make kerf cuts for beveling,
miters, inboard ripping and outboard ripping.
5. Turn the saw on. 6. Unlock the arm (see section ”Adjusting the cutter
head height”), then slowly lower the cutter head to
perform A 1/16” depth cut in the work table.