Genesis Multiple G9F18 AU000 User manual

Genuine Accessories
Electronic Installation Instructions
Glasses Gloves
Mask Hearing Protection
Part Weight (Gross) FMVSS 110 Compliance Information
1) Read the entire Installation Instructions prior to beginning the installation of this accessory.
2)
3) Make sure the vehicle is completely clean and dry in the area(s) the part is to be installed.
4)
Ensure the vehicle is properly protected in the area(s) that the accessory is to be installed.
5)
NEVER place tools on painted surfaces, seating surfaces, dash pad, console or floor carpet/mats.
6)
Always wear appropriate personal protective equipment, including gloves, safety glasses, etc, when required.
No.
1
2
www.genesisaccessories.com/installation_sheets/g9f18_au000.pdf
If applicable, scan the barcode label located on the accessory part or packaging prior to installing, to register the part. If this accessory is installed as a
replacement, register the removal of the old part before registering the new part. Old and new parts will have different barcode data, and the old
registration cannot be reused.
(C) Master Technician or Specialist
Part No.
Multiple
Difficulty stated above reflects the minimum level of
expertise required to install the accessory:
( A )
0.18
Qty
4
0.40
All dealers must determine if the Net weight they have added in the form of all options or accessories, when added to the weight of all Port/Dealer Installed
options or accessories, exceeds the lesser of 1.5% of GVWR or 100 lbs. If the additional weight does exceed the lesser of the indicated thresholds, a “Load
Carrying Capacity Reduced” label must be installed. A black, fine-point, indelible marker must be used to write by hand onto the label, the reduced carrying
capacity in kilograms or pounds, which is the total weight of all added options and accessories.
Load Label Part Number: NP070 - 09003
Denotes cautions to be taken to avoid
vehicle and component damage
Denotes cautions to be taken to avoid
physical injury or electronic component
damage
None
Language
English
4/7/2022
Cargo Blocks
(A) Customer
Rev. Date
Difficulty:
Model Year
Multiple
G9F18 AU000
Note:
Vehicle Model:
Accessory:
(B) Dealer Technician
Instructional Symbols / Definitions
If this is a printed copy of the installation instructions, ensure you have the latest revision by
scanning the QR code or by entering the website address listed below before beginning
installation. Use the latest revision date as noted by “Rev. Date” above.
Cargo Blocks
Description
Kit Overview
1
Quick Reference Guide
Application Notes
kg
Notes to the Installer:
lbs
Denotes quality processes to be checked
prior to moving to the next step
Basic Required Tools
This product is intended for use on carpeted surfaces only, view application chart on Page 3.
N
O
T
E
Denotes important information to be
reviewed during the step
Denotes specific tools that are necessary
to complete a step
Denotes personal protective equipment (PPEs) that
may be required for a step. Examples of safety
equipment icons noted below:
Denotes warnings that may lead to
serious physical injury or vehicle damage
1
2
ISHY025
Revision Date
04/07/2022
Page 1 of 3

Genuine Accessories
N
O
T
E
A. Open the rear hatch.
B. Remove Cargo Blocks from the packaging.
N
O
T
E
N
O
T
E
WARNING: Unstable cargo could become unbalanced during driving. Place
cargo in the most stable position before driving.
Cargo is most secure when its weight (Max 15 lbs) and center of gravity are
lowest to the ground.
A. Open the rear hatch.
B. This product is intended for use on carpeted surfaces only.
C. Place Cargo Block(s) on vehicle floor hook side down surrounding the
cargo to be restrained. Ensure the weight of the item is on the block face.
NOTE: Insufficient weight on the block face may result in unstable Cargo
Block(s).
D. Ensure the Cargo Block(s) are properly positioned against the cargo.
N
O
T
E
1
2
WARNING: Cargo Blocks(s) will not restrain cargo during heavy braking or
accident. Unrestrained cargo can cause injury.
A. To move Cargo Block(s), lift up vertically until block is disengaged with the
floor, then reposition.
1
NEW VEHICLE INSTALLATION, PLEASE FOLLOW STEPS BELOW
FOR CUSTOMERS, PLEASE FOLLOW STEPS BELOW OR REFER TO THE QUICK REFERENCE GUIDE
A. Place Cargo Blocks on the floor in the shape of a one (1) foot square,
with bottoms facing each other as shown. This is the recommended
position for demonstrating this accessory.
2
ISHY025
Revision Date
04/07/2022
Page 2 of 3

Genuine Accessories
Cleaning Instructions for:
* Carpet side facing up only
2023~

-
Not Applicable

Vehicle Load Floor
Cargo Mat
Cargo Mat, Up Seatback
*Cargo Tray, Reversible



Not Applicable


-
-
-
-
Not Applicable
-



-
-
The Cargo Blocks can be wiped, swept, lightly vacuumed, cleaned with water, or soap and water.
Do not use petroleum-based solvents for cleaning.
Ensure the Cargo Blocks are completely dry before placing them in the vehicle.
Care & Cleaning
Cargo Blocks are stable and seated on the floor surrounding the item.
Multiple
Cargo Blocks
2021~
G80
Vehicle Model
Model Year
GV80 (7-Passenger)
Cargo Blocks are in place.
Visual Check
Item to be Checked
Result

-
-
G80 EV
2022~

-
-
-
GV60
G70
2022~
2021~
G70
2019~2021
GV80 (5-Passenger)
2021~
Application Chart
Accessory Compatibility
ISHY025
Revision Date
04/07/2022
Page 3 of 3