Genexis Pure Series User manual

F510 & F530
Pure-Series
Installation Guide

Status
Green – power on
Yellow (blinking) – booting
Red – boot failed
Uplink
Green – link ok
O– no link
Internet (IP connectivity)
Green – connected (DNS available)
Green (blinking) – connection failed (no DNS available)
O– no IP connectivity
Phone
Green – voice service registered and ok
Green (blinking) – voice service failed to register
O– no voice service present or registered
Wireless (WiFi)
Green – wireless network 2.4GHz and/or 5GHz active
O– wireless networks inactive
TV
Green – TV service registered and ok
O– no TV service present or registered
Mode button
Activate WPS – press and hold 3seconds
Disable/Enable WiFi – press and hold 10 seconds
LED & button overview
Reset button
LAN ports
USB 2.0port
Telephone
ports
ON/OFF
button
Power port
Port overview
Reset button
The reset button resets the modem to factory
settings. You can press this button with a small
pin or paperclip. Press and hold the button for
more than 10 seconds.
ON/OFF button
This enables you to turn your Pure F510/F530
ON or OFF.
Lid
TV port

Pure F510/F530 needs to be connected to an optical broadband network.
Getting started
Check if the following items are in
the giftbox:
• Genexis Pure F510/F530
• Power adapter
• Vertical stand
• Strain relief
• Labels (self-adhesive, 2x)
• Rubber feet (self-adhesive, 4x)
• Plugs & screws (2x)
Connecting the fiber
1. Slide the lid of the housing by sliding it
towards the portside.
2. Attach strain relief to the fiber, 58 mm
from the connector.
3. Remove the dust cap from the pigtail and
the connector, do not touch the fiber tip.
4. Connect the pigtail to the fiber interface.
5. Place strain relief in the plastic notch in
the housing at the highlighted area.
6. Slide the lid back in original position on
the housing.
Warning: do not pinch the fiber while
sliding the lid back in position.
Multiple languages of this document and additional product information are availableon
https://genexis.eu/product/pure/downloads
Installation guide
Label position
The product label is positioned on the bottom
of the active device.
Placement
Pure supports two placement options;
standing and mounted to a wall. It is
recommended to place the device ‘away’
from obstacles and objects.
Standing
1. Attach the four rubber feet to the
bottomside of the vertical stand.
2. Slide the vertical stand onto the bottom
of the Pure F510/F530.
3. Place the device on a flat surface.
Wall mount
1. Download and print the drilling guide from
https://genexis.eu/product/pure/downloads
2. Use the drilling guide to drill the holes,
insert plugs and put screws into place.
3. Use the wall mount points on the back
of the Pure F510/F530 to mount the
device to the screws.
Warning: do not cover the device with
anything, this will interfere with the
ventilation of the Pure.
Operation Temperature 0°C ~ 40°C
Setting up the Pure
1. If required, connect your telephone to the
phone port via an RJ11 network cable.
2. If required, connect your personal devices
to the LAN ports via an RJ45 network cable.
3. If required, connect your television /set-
top box to the TV port with a coax cable.
4. Connect the supplied power adapter to
the Pure and plug the adapter into a power
socket.
5. Press the power button at the back of the
Pure F510/F530 to turn on the device.
6. The colored LEDs on the Pure F510/F530
panel will start blinking. This process takes
about 2minutes.
7. If the device is connected properly and
the service is active on the fiber port, the
Status, Uplink and Internet LEDs will have
a fixed green color.
Connecting the Wireless Local Area
Network (WLAN)
Pure supports two ways to create a wireless
connection with your personal devices; via
WPS or manually. For personal devices that
support WPS, this will be the easiest method.
WPS
1. Make sure the WiFi indicator LED on the
front panel is lit. If not, press the Mode
Pigtail in
fiber interface
Strain relief
58mm

Troubleshooting
button for 10 seconds until it gets lit.
2. Press and hold the Mode button for 3
seconds. The WiFi indicator LED will
start flashing.
3. Follow the instructions of your personal
device to complete the connection process.
Manual setup
1.Make sure the WiFi indicator LED on the
front panel is lit. If not, press the Mode
button for 10 seconds until it gets lit.
2. Perform a search for available wireless
networks using the personal device i.e.
laptop or mobile device.
3. Compare the list of wireless networks with
the network name which is shown on the
Pure F510/F530 label.
4. Connect by clicking on the corresponding
network name and provide the password,
which is shown on the Pure F510/F530
label called “WiFi-Key”.
Power saving options
Power saving options are available via the
web interface. For more information please
visit http://router
Is the Status indicator LED o?
Check if the modem is properly connected
to the power adapter.
Check if the power adapter is connected to
an electrical outlet.
Check if the device is turned on – the ON/
OFF button should be in the “pressed” state.
If the modem is properly connected and
turned on, the Status indicator LED should
turn green after a while.
If Status indicator LED is RED for a long time,
contact your service provider.
Is the Status indicator LED red?
Contact your service provider.
Is the Uplink indicator LED o?
If the Uplink indicator LED is o, despite proper
connection, contact your service provider.
Reset the device
The reset button resets the modem to factory
settings. You can press this button with
a small pin or paperclip. See chapter ‘Port
overview’ to locate the pinhole.
Press and hold the button for more than
10 seconds.
Company Name
Genexis B.V.
Company Address
Lodewijkstraat 1a
5652 AC Eindhoven
The Netherlands
Name and title of authorized person
Maarten Egmond, CTO
Signature of authorized person
Place of issue Date of issue
Eindhoven 2020-12-16
The Netherlands
Hereby, Genexis B.V. declares that the radio equipment type Pure F510/F530 is in compliance with
Directive 2014/53/EU, Directive 2009/125/EC, Directive 2011/65/EU and Delegated Directive
2015/863.
The full text of the EU declaration of conformity is available at the following internet address:
https://genexis.eu/product/pure/red/pure-f510
https://genexis.eu/product/pure/red/pure-f530
Frequency bands and maximum radio frequency power transmitted
The Pure F510/F530 operates in the frequency bands of 2,4Ghz and 5Ghz.
The maximum radio frequency power transmitted in these bands is:
• 20 dBm(100 mW) (EIRP)for the 2400 MHz – 2483.5MHz band
• 23 dBm (200 mW) (EIRP)for the 5150 MHz – 5350 MHz band *
• 30 dBm (1000 mW) (EIRP) for the 5470 MHz – 5725 MHz band
* In EU, 5150 – 5350 MHz is restricted to indoor.
EU Declaration of Conformity

Revision 1.0- December 2020 - Copyright © 2020 Genexis B.V. All rights reserved.
Genexis assumes no responsibility for any inaccuracies in this document. Genexis reserves
the right to change, modify, transfer, or otherwise revise this publication without notice.