Genie IP8ESP User manual

IP8ESP
8 Port PoE Ethernet Switch
User Manual

IP8ESP - 8 Port PoE Ethernet Switch
2
Key Features
• 8 x 10/100Mbps PoE Ethernet Ports
• Provides up to 30W Consumption
• 2x gigabit Uplink Ports
• Resettable Button for each PoE Port
• Up to 1M packet data cache
• Up to 8K for the MAC Address
• Redundance Power Design
• Fast and easy installation, convenient for wall, din rail and desktop installation
Introduction
IP8ESPisan8portPoEEthernetswitchthathasbeendesignedspecicallywiththesurveillance
market in mind. It supports fast packet forwarding which is essential when trying to provide clear
imagesanduenttransmission.
Application
NVR
Gigbit Media Converter
Optical Fiber
PoE Switch
Cat5/5e/6 Network Cable
PoE Network IP Camera
PoE Dome Camera
PoE PTZ Camera
PoE Network Dome Camera
Installation Steps
1. Pleaseturnoffthesignalsourceandthedevice’spower.Installationwithpoweronmay
damage the device.
2. Use8networkcablestoconnect8IPcameraswithPoEswitch’s1~8PoEPort.
3. Useanothernetworkcableor(opticalber)toconnectPoEethernetswitch’sUplinkportwith
NVR or computer.
4. Connect PoE switch with power adapter.
5. Check if the installation is correct and device is good, make sure all the connection is reliable
and power up the system.
6. Make sure every network device has power supply and work normally.

IP8ESP - 8 Port PoE Ethernet Switch
3
Technical Specication
Model Number IP8ESP
Power Supply Power Adaptor
Voltage Range DC48V - 57V
Consumption <5W
Network Port 1~8Port:10/100Mbps
CCTVMode:10Mbps
UplinkEthernetPort:10/100/1000Mbps
SFP:1000Mbps
Transmission Distance DownlinkPort:0~150m
CCTVMode:0~250m
UplinkPort:0~150m
SFP:DependsonSFPModulePerformance
Transmission Medium Cat5e/6 standard Network Cable
PoE Protocol IEEE802.3af/at
PoE Power Supply End Span
PoE Power Consumption SinglePort≤30w
Network Standard IEEE802.3 10BASE-T,IEEE802.3u 100BASE-TX, IEEE802.3ab
1000BASE-TX;
IEEE802.3z 1000-SX/LX;
IEEE802.3 X
Package Data Cache 1M
MAC Address List 8K
Power Indicator Front:1pcRedLight
Side:1pcRedLight
Optical Port LED Indicator 1SPFPortIndicator:GreenLight
Uplink Network Port LED Indicator 1pcNetworkWorkingStatus:GreenLightonRJ45Port
Downlink Network Port Indicator 1~8Ports:GreenLightindicatesNetworkStatus,YellowLight
indicates PoE Status
PoE Reset Button 8,Correspondingwith1~8port,PoEresetafterpressthebutton
Reset Button 1pc, Machine Reset
Port Lightning Protection Level3,Per:IEC61000-4-5
ESD Level3,Per:IEC61000-4-2
Temperature Conditions Working:-40°C~75°C
Storage:-40°C~85°C
Humidity:0~95%(Non-Condensing)
Dimensions(LxWxH) 159x110x46.5mm
Weight 575g
Featuresandspecicationsaresubjecttochangeforfurtherimprovementwithoutanynotice

IP8ESP - 8 Port PoE Ethernet Switch
4
Troubleshoot
• Make sure the equipment is installed according to the manufacturers installation guide.
• ConrmRJ45cableordermeetsEIA/TIA568Aor56Bstandard.
• Every PoE port can provide PoE equipment maximum power less than 30W, please do not
connect the PoE equipment with power over 30W.
• Replace the equipment that can not work with a proper functioning 8 Port PoE ethernet switch
to check if the equipment is damaged.
• Please contact your vendor if trouble still exists.
Board Diagram
Front Left Side
Back Top
1. FrontboardwithPoEethernetport,theyellowlightontheRJ45socketleftsideistoindicate
the PoE status The green light on the right side is to indicate the network status and the yellow
lightandgreenlightontheUplinknetworkRJ45socketistoindicatethenetworkworking
status. The LED on the SFP optical port left side is to indicate power and optical port working
status.
2. TheleftboardandbackboardhaveaDC48V~57Vpowerinputport,defaultwitha120W
power adapter. The PoE output consumption of every port is 15W with the maximum output
consumptionbeing25W.Ifyouneedeachportoutputtobe25W,thenyou’llneedtohave
another 120W power adapter in addition or use a 240W power adapter.
Power/Uplink
Optical Port
Indicator
SFP
Optical
Port
Uplink
Network
Port
PoE Network Port Power Input
Power Input Grounding
Terminal
PoE Port Reset Button
Reset
Button
Power
Indicator

IP8ESP - 8 Port PoE Ethernet Switch
5
Plug Producing Method
1. Please remove 2cm long insulating layer and bare 4 pairs UTP cable.
2. Seperate the 4 pairs UTP cable and straighten them.
3. Line up the 8 pieces of cables per EIA/TIA 568A or 568B.
4. Cut off the cables to leave 1.5cm bare wire.
5. Plug8cablesintoRJ45Plug,makesureeachcableisineachpin.
6. Use the wire crimper to crimp it.
7. Repeat above 5 steps to make another end.
8. Use a network tester to test the cable if it works.
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
EIA/TIA 568 A EIA/TI A 568B
Pin Colour Pin Colour
White / Green White / Orange
Green Orange
White / Orange White / Green
Blue Blue
White / Blue White / Blue
Orange Green
White / Brown White / Brown
Brown Brown
• WhenyouchooseRJ45,makesureifoneendisEIA/TIA568A,theotherendshouldalsobe
the same.
• WhenyouchooseRJ45,makesureifoneendisEIA/TIA568B,theotherendshouldalsobe
the same.

GENIE CCTV LTD.
CCTV House, City Park, Watchmead, Welwyn Garden City, Hertfordshire, AL7 ILT
Tel:+44(0)1707330541Fax:+44(0)1707330543
www.geniecctv.com
Edition. GN-November 2015