Genie AC POWERED SCREW DRIVE OPENERS User manual

Operation and
Maintenance Manual
3628336241
TABLE OF CONTENTS
Warranty Information ................... 2
Safety Information ..................... 3
Safety Features ......................... 3
Important Installation Instructions ....... 3
Pre Installation Checklist .............. 46
Adjustments .......................... 7=8
Programming the Remote Control ..... 89
Installing Lightbulb and Lens ............ 9
Scheduled Maintenance ............... 10
Troubleshooting Guide ............. 1011
Wiring Diagram ........................ 12
Parts Lists and Exploded Views ...... 1213
Accessories ............................ 14
COMPLETE WITH mNTELLlCODE
REMOTE CONTROL AND SERIESli
For up to 7'-6" tall Doors. (Extension Kit avaimable for 8' Doors)
included Wail Control MUST be installed prior to Operation of
this Garage Door Operator.
Safe-T-Beam ®Safety Reverse System Must be installed and
the Force Controls MUST be Properly Set to close door.
This Equipment meets or exceeds all Federal, State and UL325

THEGEN|ECOMPANYLIMITEDWARPJ ,NTY
What iscoveted?
Any defect [n material and product workmanship from personal,normal
household use [naccordance with the Owner's Manual.
For how long?
MODEL2560... 1Syears on motor, 3years all other parts.
MODEL3560... Lifetime' on motor,3 years allother parts.
%[fedme=Aslong dsyou ownyour home.
Who gets the warranty?
This warranty is limited to the consumer who originally purchased
the product.
Geographic scope:
This warranty applies only to units installed and operated within the country
where they were purchased.
Limitations:
IMPLIEDWARRANTIES,INCLUDINGTHOSEOFFITNESSFORA PARTICULAR
PURPOSEANDMERCHANTABILITY(ANUNWRITTENWT_RRANTYTHATTHE
PRODUCTISFITFORORDINARYUSE)ARELIMITEDTOONEYEARFROMTHE
DATEOFPURCHASE.GENIEWILL NOTPAYFOR:LOSSOFTIME;
INCONVENIENCE;LOSSOFUSEOFYOURGENIEPRODUCTORPROPERTY
DAMAGECAUSEDBYYOURGENIEPRODUCTORITSFAILURETOWORK;ANY
SPECIAL,INCIDENTALOR CONSEQUENTIALDAMAGES;ORANY DAMAGES
RESULTINGFROMMISUSEORMODIFICATIONOFYOURGENIEPRODUCT.
Somestatesand provinces do not allow limitations on how long animplied
warranty lasts or the exclusion of incidental or consequential damages,sothe
above limitations or exclusionsmay not apply to you.
This warranty isthe only one we will give onyour Genieproduct, and itsets
forth allour responsibilities regarding your Genie product.There arenoother
expresswarranties.
Stateand province rights:This warranty givesyou specificlegal rights,andyou
mayalso have other rights which vary from stateto state and province to
province.
How to get warranty service:
To obtain warranty servicefor your Genie product, you must provide proof of
the date and placeof purchaseof the product.
1.Do-It=Yourself-Service.
Callthe Genie Customer Servicetoll free at 1.800.354.3643to speakin
person to atrained Genie representative for assistancein diagnosing the
problem and arranging to supply you with the required parts for do-it-
yourself repairs.Trained servicerepresentatives areavailable Monday-Friday,
8:00a.rn.- 9:00 p.m.,EasternTime,and on Saturday,10:00a.m.to 7:00p.rn,
EasternTime (subject to holidays)You may alsoget the information you
needat www.geniecompony.com.
2,Service From Authorized Dealers.
YoualsomayobtainwarrantyservicefromGenieauthorizeddealersbycallingthe
GenieCustomerServiceat1.800.354.3643or byvisitingw_geniecomporry.com
beforeschedulingwarrantyservice.Ifwarrantyserviceisprovidedby anauthorized
dealer,Geniewilt provideallrequiredpartsunderwarrantyat nochargetoyou,but
thedealersareindependentbusinesspeopleandmayrenderabenchor servicecall
chargeforthek services.Geniewill notreimburseyouor otherwiseberesponsiblefor
thosecharges.
Wesuggestthat youretainyouroriginalpackingmaterialintheeventwechooseto
repairor replaceyourGenieProductandrequestthat you shipit to us.Besureto
includeyourname,address,telephonenumber,proofofdateandplaceofpurchase
andadescriptionof theoperatingproblem.Afterrepairingor replacing,yourGenie
product,we willshipit to yourhomeatno costto youfor partsandlabor,but youwill
haveto payaminimumof$5.00for shippingandhandlingcharges.
Yourchoiceofeitheroneoftheabove-describedserviceoptionsisyourexclusive
remedyunderthiswarranty.
What this warranty does not cover:
Thiswarrantydoesnotcoverbatteries(whichareconsideredreplaceableparts),
installation,commercialuse,defectsresultingfromaccidents,damagewhilein transitto
ourservicelocationor damageresultingfromalterations,misuseorabuse,lackofproper
maintenance,unauthorizedrepairor modificationoftheproduct,affixingofany
attachmentnotprovidedwith the product,programmingof theRemoteControl
Devices,Safe-T-Beam®adjustment/cleaning,staplesthroughwiring,pinchedor broken
wires,Carriagedisengaged,ForceContro!adjustments,dooroutof balance,broken
springsorcables,poweroutages,useofextensioncords,missingor damagedpartson
discounted,clearanced,finalsaleortaped cartons,phantomoperations(laborisnot
coveredif Openerisfunctioning properlywhile technicianisin garage),fire,flood,or
actsofGod,or otherfailureto followtheOwner'sManual
Pleasenote the following information,soit isavailable if you
need to call us.
Date Purchased //
Serial Number
Operator Model
Remote Control Model
Model Number and
Serial Number are
located on front panel
inside the lens,
jj_
}
/
./
j_
WK YR P [
27 94 4 H
Serial/Mfg No.
Pleasekeep original or photocopy ofyour sales receipt
with this manual for future reference should service
ever be requiredo
INCLUDEDIN THIS PACKAGE
Manual 1)Warranty Information
2) Pre Installation Checklist to be reviewed prior
to any assembly or installation
3) Necessary Adjustments
4) Programming Remote Devices
5) Maintenance and Troubleshooting
6)PartsExplosions
7)AccessoryOrderForm
8) Door Opener Association Safety and
Maintenance Brochure (DASMA)
9) Entrapment Warning Label =To be Adhered in
close proximity to wall control
Poster 1) Pictorial and step by step opener assembly
instructions
2) Pictorial and step by step opener installation
instructions
iT IS CRITICAL THAT ALL SAFETY WARNINGS
MARKED CLEARLY [N BOTH THE MANUAL
AND POSTER ARE READ, UNDERSTOOD AND
FOLLOWED.
Visit Our Website at: www.geniecompany.com
FORANSWERS,"CALL 1,800,354,3643
SAVETHESE INSTRUCTIONS
2 For Help, call 1=8OO-35-GENIE or visit www.geniecompanyocom

OVERVIEW OF POTENTIAL HAZARDS
Overhead doors arelarge,heavyobjectsthat movewith the help ofsprings under high tension and electric motors. Sincemoving objects,springsunder
tension,and electric motors can causeinjuries,your safetyand the safetyof others depend onyou reading the information in this manual. Ifyou have
questions or do not understand the information presented,callTheGenie Company.or your local GenieDistributor.
Hnthis section, and those that follow, the words Danger, Warning and Caution are used to emphasize important safety
information. The word:
_, DANGER; indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
A WARNING; indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
A CAUTION; indicates a potentially hazardous situation which, if not avoided, may result in injury or property damage.
The word NOTE is used to indicate important steps to be followed or important considerations.
POTENTIALHAZARD
MOVINGDOOR
ELECTRICALSHOCK
HIGHSPRINGTENSION
EFFECT
WARNING:
Could result in death
or serious injury.
WARNING:
Could result in death
or serious injury.
WARNING:
Could result in death
or serious iniury.
PREVENTION
Keep people clear of opening while door is moving.
oDo Not allow children to play with the door operator.
Do Not operate a door that jams or one that has a broken spring.
oTurn off power before removing operator cover.
oWhen replacing cover, make sure wires are not pinched or near
mowng parts.
oOperator must be properly grounded.
oDo Not try to remove, repair or adjust springs or anything to
which door spring parts are fastened, such as,wood blocks,
steel brackets, cables or other like items,
oRepairs and adjustments must be made by a trained door
system technician using proper tools and instructions,
MPORTANT INSTALLATION
NSTRUCTIONS
zLWARNING:
TO REDUCETHERISKOFSEVEREINJURYOR DEATH:
1 READAND FOLLOW ALL SAFETY.INSTALLATIONAND
OPERATIONINSTRUCTIONS.If you have any
questions or do not understand an instruction, call
your authorized Genie installation professional.
2 Do Not install operator on an improperly balanced
door. Animproperly balanceddoor couN cause
severe injury. Repairs and adjustments to cables,
spring assembly, and other Hardware must be made
by a trained service person using proper tools and
instructions.
3 Remove all ropes, and disable all locks connected to
the door before installing operator.
4 tnstall door operator 7 feet or more above the floor.
Mount the emergency release knob 6 feet above
the floor.
5 Oo Not connect the operator to the source of power
until instructed to do so.
5 Locate the control button:
[ Within sight of door,
At a minimum height of,5 feet so small children
cannot reach it_
, Away from all moving parts of the door.
7 Install the entrapment WARNING labet next to the
wal button or console. Install the emergency release
tag on, or next to, the emergency release
8 The operator must reverse when the door contacts a
1-1/2 inch high object on the floor at the, cen!er of
the doorway[Thisisabout the sizeof a2 x 4 board
laid flat.
SAFETY FEATURES
Safe-T-Beam ® (STB) Non-Contact Reversing System
Places an invisible beam across door opening, that reverses
the door during down travel to the fully open position if
anything passesthrough beam.
Safe-T-Reverse ® Contact Reversing System
Automatically stops and reverses a closing door within 2
seconds of contact with an object.
Safe-T-Stop ® Timed Reversed System
Automatically opens a closing door, if door does not close
within 30 seconds,
ForceGuard ® Control
Used to set the force required for opening and closing
door. For maximum safety, set the minimum force required
to fully open and close door.
Automatic Lighting System
Light bulbs up to 60 Watts max., used for safer entries and
exits, The lights turn on when door isactivated and
automatically turn off 4,5 minutes later.
Manual Emergency Release
Allows the garage door to be opened or closed manually
for emergencies or maintenance,
For Help, ca!l 1-800-35-GENIE or visit wwwogeniecompany,¢ora 3

PRE-INSTALLATiON CHECKUST
This Opener includes parts and supplies needed to install in most
garagesand connect to most garage doors. There aremany variations
of garages and garage doors, Afew additional parts and supplies may
be needed to install Opener into your garage andconnect to your
garage door. While checking items listed below, note any additional
items you will need,
Tools used in this section:
12'+Tape Measure • Pendl • Ladder • Level
Check following items before assembling Opener:
CHECK DOOR CONDiTiON AND
THICKNESS
Checkcondition of vertical stile in center of door, and its connection to
door's top and bottom beams. (Figure 2)
A If door frame isnailed together and not asolid connection, door
frame must be braced or reinforced before installing Opener,
B If door is'lightweight" (made with frame and skin- not solid),
door (including door frame) must be braced or reinforced before
installing Opener.
C A door opener reinforcement bracket may also be needed to
connect garage door to Opener's Door Bracket. This Opener is
designed for instalIation on a proper{y braced sectional door or
solidly braced one-piece door.
D Contact your Genie FactoryAuthorized Dealeror dealer of your
garage door for any necessarybracing and adoor opener
reinforcement bracket (if needed) before proceeding.
E If you have a wooden door, measuredoor's thickness. If your door
islessthan 2"thick, brace door or useshorter Door Bracket LagScrews
(1/4" x I-I/4" - not included)
CHECK GARAGE DOOR
ALIGNMENT_ OPERATION_
AND BALANCE
A Raisedoor, check alignment and seeif it moves freely (Figure 1). If
door appearsout of alignment, binds, or does not move smoothly,
contact aGenieFactory Authorized Dealeror dealer of your garage
door for repairs and adjustments to door mechanism,
B Raisedoor to 3' - 4' above ground and carefully letgo, Door
should stay stationary. Slight movement is acceptable, More than
slight movement means door isout of balance, Contact a Genie
FactoryAuthorized Dealer or dealer of your garage
door for repairs and adjustments to door mechanism,
KEEPFEET CLEAR OF DOOR
Sectional _ _q--_j'_ One-Piece
Door _ - Door
Figure 1 Checking door balance
C Checkdoor type. Make anote of whether it isasectional or aone-
)iecedoor for referencelater (Figure 2).
Ifyour door Sticks,binds,or isout of balance,have it adjusted
bya Genie Factory Authorized Dealer. Door springs,cables,
pulleys, brackets and associatedhardware are under extreme
tension and can Causeserious injury or death.
SECTIONAL DOOR, TORSION SPRINGS SECTIONAL DOOR, EXTENSION SPRINGS
J'_;:>" Extension
Center "::::-_] :: I]
q_:]]
ONE-PIECE DOOR, TRACKLESS
Header Area
Center Stile
Figure 2 Note DoorType
MEASUREGARAGEDoor HBGHT
Measuredoor height (floor to top of door) using atape measure.
This new GarageDoor Opener isdesigned for doors up to and
including 7'6" tail. Ifdoor height is 7'6" or lesscontinue to CheckStep 4.
C Ifdoor height is8'-0'_you need a RailExtension Kit.(Figure 3).
(SeeAccessoriesOrder Form,Page14).
D Ifthe door height istaller than 8'-0",the opener you purchased is
the wrong version.Contact your Customer ServiceRepresentative
at 1-800-354-3643. E×,eos oofor
8"door
@m-- _ ---e
l__ Figure 3Rail Extension Kit
A
B
CHECK DOOR HEADER AREA
The header is a heavily reinforced section of the wall just
above the top of the garage door opening.
A Findvertical center line of door and header:
Closedoor.
Measuredoor width at top.
Marka point atcenter of door and on header directly
above door. Drawacenter line to connect points.
B FindHeaderBracket mounting height (Figure 4): (Donot attach
Header Bracket).
Raisedoor, watching top edge of door and stop door
when its edge reachesits highest point.
Measuredistance ("H") from top edge of door to floor.
Forsectional doors, add 2-1/2" to "H': Marka point
on center line. Bottom of Header Bracket wiII be
installed here.
Forone-piece doors, add 6" to'H': Mark this point on
center line. Bottom of Header BracketwiII be
installed here.
SECTIONAL DOOR ONE-PIECE DOOR
H+24/2"_ _ H+d"
/7
HEADER _IEADER
Figure 4 Find Highest Point of Trave[
4For Help, call 1-800-35-GENIE or visit www, geniecompanyocom

o Foralltypes and stylesof doors:
- ff the ceiling ,inyour garage is so low that there is
not at least a 3 space above the Header Bracket
mountingpolnt, contact a Genie Factory
AuthorizedDealer.
If a door spring isin the way, place the Header Bracket
above the spring. Do Not move the door spring.
Door springsareunder extremely hi
should be handled ONLYby a trained professional. I
C Checkwall for a stud or a solid header at your mark: (Ifchecking a
finished waJi,astud finder may be helpful).
, If location isabove Header,a 2" x 6" board must be
screwedto studs beside your mark with at least two Lag
Screwsand FlatW'ashers(not provided).
Transferyour markto new mounting board.
CHECK POWER HEAD
MOUNTING AREA
Check ceiling or space above where Opener Power Head will be
mounted (Figure 5): There must be a120Volt grounded outlet or
wiring box within 3feet of Power Head.
outlet
(7'-6"door
Door Center Line
Figure 5 Check Power Head location
A The measurements above aretaken from the garagedoor
centerJinetoward the rear of the garage.
B Findlocation of ceiling joist or trussabove where Opener Power
Headwill be and estimate type and quantity of materials needed for
your installation (Figure 5A & B).
MOUNTING EXAMPLES
Perforated Angle Iron Conduit
Figure5A
OPENCEILINGSStrapsand angle iron may attach directly to joists
or trusses.
Wood
For HeJp, can 1-800-35-GENIE or visit www,geniecompany,¢om
Perforated Straps FiNiSHEDCEILINGS
Locateceiling joists or trussesusing
astud finder or similar device.
Attach angle iron(not included) to
joistsor trussesthrough finish
material using Lag Screws.
Figure6B
CHECK CEmLmNG FOR GROUNDED
PowER SOURCE
A Checkthat there is a 15Amp 120Volt grounded electrical
outlet or grounded permanent wiring box (per building code)
within 3'of Opener Power Head:Figure 5
• If not,an outlet or wiring box must be installed. Contact
alicensed electrician for installation.
• If building codesrequire permanent wiring, Power Head
must be partially disassembled to install appropriate
wiring in placeof PowerCord. (SeeAssemblyand
Installation Poster.)
Permanent wiring must be installed by a Licensed
Emectri¢ian. Not all Genie Factory Authorized Dealers
are Licensed Electrician's. Contact someone who isa
Licensed Electrician.
WARNING •
0
Do Not use an extension cord! Extension cords can
De Net use portable generator! This product is
designed to operate using standard house current.De
Not use alternate power supplies,
MOUNTmNG BRACKET LOCATmON
Check for wood garage frame, jamb, or masonry at mounting
[ocation (6" above floor) with attachment tabs facing away
from garage door (Figure 7L
A If you cannot mount Safe-T-Beam_ Mounting Bracket to
wood frame:
Concrete screws and concrete anchors (not incHuded)
must be used to mount Brackets on masonry with
attachment tabs facing away from garage door.
Source
Sensor .,d_-,
, _-
Safe-T-Beam® _ Top of
Mounting Brack_/_ !.. Bracket @'above
Figure,Mount,ng
Safe_T_Beam® _ floor
Components

RECOMMENDED TOOLS
A
BTools (Figure 8): Additional took to make installation easier:
Slotted and phi[Hps screw=driver bits
Stud finder
Sheebmeta[ cutting snips
REMOVE EXISTING GARAGE
Door LocKs
Check that the garage door locks, rope, and T-Handles are
removed from the garage door before starting the instaHHation.
A ffyour garage does not have a separate entry door, it is
highHy recommended to install[ aGenie Emergency Release Kit
(GER-2). Emergency Release Kit lets you open the garage door
from outside if there is apower failure. (Please see Accessories
Order Form on page 14.)
Before going further, get any items and tools if needed
for your installation
_7 Garagedoor frame reinforcement brackets,screws,bradng
or reinforcement kits (dealer)
_7 LagScrews(1-1/4") for a wood door lessthan 2" thick (store)
_7 Electricaloutlet and/or wiring (supplied byalicensed electrician)
_7 Sufficient angle iron or strapping for hanging PowerHead (store)
_7 60Wan light bulbs (Rough service bulbs recommended)(store)
_7 GER-2EmergencyReleaseKitfor entry during power failure (store)
_7 Wood for header,ceiling, and/or door braces (store)
_7 Masonry fastenersfor Safe-T-Beam€:'Bracket installation (store)
_7 Safe-T-Beam_"BracketExtensions (dealer)
_7 Masonrydri[[ bit (store)
_7 Extension Kit (for 8'Garage Doors)(dealer)
Go to Assembly and Installation Poster for full
Installation Instructions,
I/t6" 5/32" Tape Measure_
DriH Bit DriH Bit
6' or 7'
Step Ladde_ Wire Phi[bps Screwdriver
Stripper
AdjustaMe Wrench FUat BUade Screwdriver
/
Hammer Safety, GUasses r/l_ _-_
PenciU
1/4" 5/16" 3/8" 7/16" I/2" 9/16"
Sockets
Hack Saw Wrench
IMPORTANT
SAFETY INSTRUCTIONS
SEVEREINJURY OR DEATH
1 READANDFOLLOWALLINSTRUCTIONS.
2 Neverletchildrenoperateor playwith the DoorControls,Keepthe
RemoteControlawayfromchildren.
3Alwayskeepthemovingdoor in sightandawayfrom peopleand
objectsuntilthedoor iscompletelyclosed.
NOONESHOULDCROSS]HEPATHOFAMOVINGDOOR.
4 NEVERGOUNDERASTOPPED.PARTIALLYOPENDOOR.
5 TestOpenermonthly.Thedoo_MUSTreverseon contactwith
alq/2 highobject(ora2 x4 board[aidflat)atthecenterofthe
doorway'onthefloor.Afteradjustingeitherthe Forceorthe Limit
oftraveLretestthe DoorOpener.Failureto adjustthe Opener
properlymaycausesevereinjuryor death.
7 KEEPGARAGEDOORSPROPERL_BALANCED.SeeOwner's
Manual.An improperlybalanceddoor increasesthe riskof severe
injuryoFdeath. HaveaGenieFactoryAuthorizedDealermake
'epaksto cablesspringassembliesandotherhardware.
8 SAVETHESEINSTRUCTIONS.
NOTES, REMINDERS
Carpenter's LeveU
Figure 8 Recommended Tools
6 For Help, call 1-800-35-GENIE or visit www, geniecompanyocom

MAmNTENANCE AND ADJUSTMENTS
ADJUSTING LiMiT SWITCHES
AND FORCE CONTROLS
WARNING:
• A moving garage door can cause senous injury or death.
Keepthe path dear.
o Position the ladder to the side of the Power Head so it is
clear of aHmoving parts of the Opener and the door.
o Setthe door Opener to use the minimum force needed
to open the door,
A CLOSE ADJUSTMENT
On front pane[ of Power Head find adjusting screw
marked "CLOSE" (Figure MA-1).
, Gently turn screw counterclockwise until it stops.
- Very little force is required to turn adjusting screw.
PressWall Console to chose garage door.
- Observe if door stops at "CLOSE" limit switch.
(Figure MA-2). If door is fully closed--adjustment is
finished. Go to "OPEN" Adjustment.
- If door stops but is not fully closed,
a. Measure distance between bottom of door
and floor.
b. Move"CLOSE"Limit Switch that same distance
toward door.
-If door stops and/or reverses before reaching the
"CLOSE" Limit Switch
a. Slightly increase CLOSE Force setting (clockwise).
-If door reverses after contacting floor, move Limit
Switch toward Power Head.
-If door fails to move, check Safe=T=Beam®System. See
Troubleshooting Section, pages 10=] 1.
Tighten Limit Switch Set Screw. Do not over-tighten
(strip} Limit Switch Set Screw.
B OPEN ADJUSTMENT
On front pane[ of Power Head find adjusting screw
marked "OPEN" (Figure MA-1).
, Gently turn screw counterclockwise until it stops.
-Very little force is required to turn adjusting screw.
PressWall Console to open garage door.
-Observe if door stops at "OPEN" limit switch.
(Figure MA=2). If door is fully open--adjustment
is finished.
- If door stops but is not fully open,
a. Measure distance between bottom of door
top of door opening.
b. Move"OPEN"Limit Switch that same distance
toward Power Head.
-If door stops before reaching the "OPEN" Limit Switch
a. Slightly increase OPEN Force setting (clockwise).
-If door fails to move, see Troubleshooting Section,
pages 10=11.
Tighten Limit Switch Set Screw. Do not over-tighten
(strip) Limit Switch Set Screw.
, Cycle opener a few times to double check settings.
Repeat adjustment steps as necessary.
Little effort isrequired to turn the Force
Adjusting Knobs.
° Ifthe door stops moving while opening or
closing, adjust the Open Force or Close Force
Controls slightly clockwise (to slightly
increase the force) and retry the step.
. The Open Force and Close Force Controls are to
be set to the minimum force necessary to
ensure the door smoothly opens and
closes completely.
*Ensurethe Carriage Assembly isengaged and is
between the two Limit Switches before
operating the Opener.
FORCE
CONTROLS
Figure MA-1 Making Force Adjustments
OPEN
OPEN
i!
CLOSE
Figure MA-2 Making Force Adjustments
For Help, call 1-800-35-GENIE or visit wwwogeniecompany, com

fTransmitter Complance Statement
Transmitters comply with al United Statesand Canadian legal requirements asofthe date
of manufacture, No warranty is made that they comply with al UegaUrequirements of any
other jurisd'iclon. Iftransmitters are to be used in another country, the importer must
determine compUiancew4h any UocaUUawsand reguUatlonswhich may differ from United
Statesand Canadian requirements prior to use.
Los transmisores cumplen con todas UasregUamentadones UegaUesde los Estados Unidos
ydeUCanad_,en Uafecha de fabricaci6n, Ninguna garantfa seda que cumplan con todas
as regamentaciones legales de ninguna otrajudsdicci6n. Silos transmisores sevan a
utlizar err otto pais,el importador debe determinar sicumplen con las reglamentaciones
y leyes locales que puedao serdiferentes alas reglamentadones de los Estados Unidos y
del Canada, antes de usar los mismos.
Les emetteurs sont conformes £ la r_gementation am@icaine et canadienne _compter
de leur date de fabrication, Aucune garantie n'est stipul@ indiquant qu'Is sont conformes
toutes les prescriptions juridiques d'autres autorit_s, Siles _metteurs sont utlis_s dans
d'autres pays,t incombe a I'importateur d'en d_terminer leur conformit_ aux lois et r_ges
locales pouvant diff@er de celes des Ctats-Uniset du Canadaavant toute utlisation
desdits 6metteurs.
Sendeger£te entsprechen alen gesetzlchen Bestimmungen in den USA und Kanadazum
Zeitpunkt der Herstelung.Wir Obernehmen keine Gew£hr[eistung fijr die Einha[tung a[[er
gesetzlichen Bestimmungen in anderen Landem,Solen Sendeger£te in anderen L£ndern
eingesetzt werden, so mussder Importeur vor dem Gebrauch sicherstelen,dass die
Sendeger£te auch sokhen Iokalen Bestimmungen entsprechen, wekhe yon den
Bestimmungen der USAund Kanadasabweichen.
£,x,l)l {_II!II __iiI I £ I?._ £ I I I _IInI _kI_ 4-1 __lSi _t£1t,_l_111°
;017l?,_!20_1-_t-_)'#,_lo)[_1c@.]1t¢'o5)tI, BI tl&l_',(0 {_/IJ/E Y_,'L0 i)]_gR$]]Z)_
niEi_O]_]E_Eke-XJ_qlA_A_ U@ #q_xb_bA_o£8_slql _Ai ujq3_ _tL_E}£_£!£
SETTING CONTACT
REVERSE FUNCTION
Limit Switch and Force Adjustments must be completed
before checking the contact reverse function (Figure _A-3).
A Open garage door using
Wall Console, Figure _A-3
B Lay a 2" x 4" board fiat in center
of doorway.
C Close door using Wail Console.
Check that door stops and reverses
within 2 seconds after it
contacts board:
, if door does not reverse, decrease
Close Force until door reverses.
, If door still does not reverse,
move Limit Switch toward door.
E Check Safe-T-Beam ° System
operation:
, If beam is blocked, door will
not close. 2" x 4" boa rd
hid fiat
ACCESSORIES
PROGRAMMING THE
REMOTE CONTROLS
, Each Remote Control must be programmed
separately.
°The Remote Controls will not cause the door
Opener to close the garage door if the Safe-T-
Beam®System is malfunctioning.
°When programminc) the Remote Controls, they
must be at least 24 from the Antenna Wire.
Ifthe red Learn Indicator Light blinks
approximately 4 times per second,
lrogramming hasstopped. If programming
as stopped, repeat the above steps.
Each Button on a 2 or 3 Button Remote Control
isfor a different Opener. You cannot use more
than one Button per Remote, per Opener.
°A maximum of seven Remote Controls or
Wireless Keypads can be stored into the
Receiver at one time. If a Remote Control
becomes lost,or if you want to delete a Remote
Control or Wireless Keypad, see To EraseAll
Receiver Memory."
A To program one Button of a Remote Control (Figure MA-4):
Locate Learn Button and Learn Indicator Light
on left side of Power Head (Figure _A-5),
Press and release Learn Button, Red Learn
Indicator Light will blink 2 times per second,
Press Remote Control Button once within 30
seconds, Red Learn Indicator Light will stay lit,
Press Remote Control Button again, Red Learn
Indicator Light will go out, indicating that
memory is stored,
Press Remote Control Button again and the door
will operate,
B Program each additional Remote using step A above
(up to seven),
To Erase AiJ Remotes from Power Head Memory
A Press and hold Learn Button on Power Head for 10
seconds or untl Learn Indicator Light goes out.
Memory is erased:
Program Transmitter/Receiver again as needed.
To Replace Remote Control Battery
A FOR NON-FLASHLIGHTMODELS
Pop offthe back of the transmitter,
- Use coin, pen, screwdriver or any similar device,
- Replace old Battery with new coin type battery,
Replace back of remote,
B FOR FLASHLIGHT MODELS
Slide open battery cover,
- Replace old Battery with new AAA battery,
Replace battery cover,
8 For Help, call 1-800-35-GENl£ or vBit wwwogeniecompanyocom

£ WARNING:
A moving garage door may cause senous injury or death.
o Keep people dear of opemng while door ismoving.
Do not allow children to play with the Remote Controls,
Ufthe Safety Reverse does motwork properly:
, Close the door and disconnect the Opener using the
Emergency Release Cord,
° Do not use the door Opener, Remote ControB, oJ
Wireless Keypad.
o Refer to the door and door Opener Owner's Manuals
before attempting any repairs.
Remote Control Operation
A Press Button on Remote Control Garage door wH[ move.
B Press Button again. Garage door wi[I stop:
The door automatically stops at the end of the open or
close cycle.
C Press Button again. Garage door will reverse.
iNSTALLLUGHTBULBSAND LENs
AInstall two 60Watt light bulbs (not included) into Light
Sockets (Figure MA-6):
oRough service, ] 30Volt bulbs are recommended.
B Insert the hooks at the bottom of the Iens into the slots
provided in the front plate of the power head (Figure MA-7).
oFtipLensupand fasten with (2) #8-32 x 3/8"Phi]]ips Pan
Head Screwswhere indicated.
U_ith Opener. Any 1
moth__pener to operate 1
mune_ stop_,orking. "
1 Button Compact Remote 3 Button Compact Remote
w/Docking Station w/Docking Station
Figure MA-4 Genie Remote Controls
Figure MA-6
Receiver Learn
Code Button
Receiver
(not to
scab)
Figure MA-5 Learn Code Button and indicator Light
Toprogram a Hemelink ®or CaJ'2U Device:
(This GDO is Home!ink _end Car2U compotible)
o Follow the Home[ink_)or Car2Uinstructions in your car
owner's manual
J
J
Figure MA=7
For Help, call 1-8OO-35-GENIE or visit wwwogeniecompany,¢om

A Monthly:
Door springs and door hardware:
Oil door roller, bearings, and hinges using silicone
lubricant or light oil
DO not operatedooiautomaticai[y or manually if springs [
are broken. Contact a Genie Factory Authorized Deater for
service orcaH Customer Service at 1.800.35.6ENIE. 1
, BaHanceDoor.
- CHosedoor.
- ReleaseCarriage Assembly from Rail Assembly by pulling
the Emergency Release Knob towards the door.
- Raise door manually 3L 4' and verify' that door staysat
that position. See Check Step 2on page 4.
When the door is 3' _4' above the ground, the door
should stay open. Slight movement is acceptable, ff
the door moves too much, contact a Genie Factory
Authorized Dealer for service or call Customer Service at
1-800=35-GENIE.
- Reattach CarnageAssemb[y to Rail Assembly:
a. Pull the Emergency Release Knob toward Power Head.
b. CHosedoor.
Contact ReverseTest.
- Perform Adjustment 2 on page 8.
WARNING:
If the door fails to reverseon contact with the board
adjust the Close Force Control as specified in Set Limit
Switches and Force Controls on page 7 & 8. If the Opener
still fails,contact a Genie Factory Authorized Dealer for
service or call Customer Service at 1-800-35-GENIE
B Yearly:
Wipe off oid excess Hubdcant from Drive Screw.
Lubricate Drive Screw with Genie Lubricant GLU-3_
UseONLYGenieLubricant(6LU-3). Other lubricants
may damage the Opener.
GLU-3
Lubricant
FCC AND [C CERTIFIED
this device must accept any interference received, indud
ins interference that may cause undesired operation.
C Asneeded
Replace lightbulbs.(See page 9)
Safe-T-Beam ® System Self-Diagnostic Troubleshooting
Source {Red LED) Sensor {Green LED} Possible Problem solution
ON ON Normal operation None required
•Power Head not powered oCheck breakers, fuses, plugs
OFF OFF •Wiring from Power Head bad •Check wiring for obvious shorts
OFF ON • Wiring to Source missing or bad • Check wiring
• Power has been interrupted o Remove power and reappiy
2 BLINKS, Pause o Beam not aligned o Check Source, Sensor alignment
(Repeat) ON o Beam obstructed o Check for obstruction
o Sensor defective o Contact Customer Service
2 BLINKS, Pause o Wire to Sensor missing or bad o Check wiring
(Repeat) OFF o Sensor defective o Contact Customer Service
-3 BLINKS, Pause • Sensor receiving interference • Determine source of interference
(Repeat) ON o Check for interference from sun-
light or a source unit on an
adjacent door
• Contact Customer Service
4 BLINKS, Pause o Source not sending pubes o Contact Customer Service
ON
(Repeat) • Source defective • Contact Customer Service
1 0 For Help, call 1-800-35-GENIE or visit www, geniecompanyocom