Genie GSP1000 User manual

Quick Start Guide
Please read these instructions carefully before operating the unit
and keep for further reference. All the examples and pictures used
here are for reference only. The contents of this manual are subject
to change without notice.
PoE Surge Protector -
10 / 100 / 1000 Mid / End
Span
GSP1000

Quick Start Guide PoE Surge Protector - 10 / 100 / 1000 Mid / End Span
2
The Genie GSP1000 is a surge protector designed for both network and power.
It features multi-level protection, large maximum discharge current, low limiting
voltage, quick reacting time, low inserting loss and supports 10/100/1000 PoE
Ports.
Features
• Standard:IEC61643–21:2000
• PoE and PoE+. Compatible with End-span and Mid-span
• Multi-function and multi-level over voltage protection, large capacity discharge
current, low limiting voltage, quick reacting time, low inserting loss
• Grounding mode: Extending Line to ground
• Simple installation
Specifications
Ethernet
Working Voltage (Un) 5V
Nominal Discharge Current
(In) 3KA
Maximum Discharge Current
(Imax) 5KA
Protection Level (Up) 25V
Rate 10/100/1000Mbps
Response Time 1ns
Insertion Loss 0.5dB
Connector RJ45
Protection Circuit 1/2 3/6 4/5 7/8
Power
Working Voltage (Un) 48V
Nominal Discharge Current
(In) 3KA
Maximum Discharge Current
(Imax) 5KA
Protection Level (Up) 200V
Protection Circuit 1/2 3/6 4/5 7/8
Others
Operation Temperature -40 C~85°C
Storage Temperature -40 C~75°C
Humidity 0~95%
Dimensions 100 × 37 × 27 mm
Weight 100g

Quick Start Guide PoE Surge Protector - 10 / 100 / 1000 Mid / End Span
3
Panel Diagram
Application
Installation Steps
Please check the following items before installation.
If anything is missing, please contact dealer.
• 1x GSP1000
• 1x User Manual
Please follow the steps as below:
1. Please turn off the power before installation, power on may damage the device.
Make sure that the network connection is reliable.
2. Use a network cable with crystal connector to connect the surge protector’s
network input and monitor, and use another network cable to connect the
surge protector and IP camera.
3. Make sure the connection is reliable, power on the device.
Gi ga bit Po E+
PoE Camera
PoE Camera
NVR
PoE Switch
Power
Cat5/5e/6 Network Cable
GSP1000
GSP1000

Quick Start Guide PoE Surge Protector - 10 / 100 / 1000 Mid / End Span
4
Checks
1. Check the grounding resistance meets the specification before connecting the
device to the system.
2. Connect the protector in front of the protected device.
3. Connect the device ground wire to protection ground strap in the shortest distance.
4. Protectors have In, Out symbol, connect output to protected device.
5. If the loss of consumption increases because of the socket bad connection etc. Please
reconnect or change the protector.
6. Do not disassemble the protector to avoid damaging the protector.
Troubleshooting
Please find the following solution when the device doesn’t work:
• Inspect the surge protector
• Using multimeter “” measuring input and output wire line resistance is 0
• If ,resistance value is too much ,please replace for a new one.
• Using multimeter “” measuring wire line resistance to ground wire (yellow
green cable), over 400k. If its resistance value is too low, such as 0, please
replace for a new one.
• If the problem still exists, please contact your distributor.

Sales [phone]
Enquiries [email protected]o.uk
Website www.genieproducts.co.uk