GENLED Acolyte DiGidot CTRLPIXELTRKITSP User manual

Page 1Acolyte is a quality division of GENLED Brands™| www.AcolyteLED.com |Acolyte | Architectural Lighting Solutions
PXLNET TRANSCEIVER KIT MANUAL
CTRLPIXELTRKITSP, CTRLPIXELTRKITST, CTRLPIXELTRKITRJ
RoHS SPI DMX IP00
REV. 22SEP2023

Page 2Acolyte is a quality division of GENLED Brands™| www.AcolyteLED.com |Acolyte | Architectural Lighting Solutions Page 2Acolyte is a quality division of GENLED Brands™| www.AcolyteLED.com |Acolyte | Architectural Lighting Solutions
THANK YOU FOR CHOOSING ACOLYTE AND DIGIDOT!
Acolyte and DiGidot offer powerful products and solutions to control LED pixels. C4
controllers are the heart of our control system, offering great exibility and simple
infrastructures. To benet from all our system advantages, we offer innovative accessories
like range extending equipment like the PxLNet Transceiver.
These products allow you to send PxLNet, which is a high speed, long-range SPI protocol.
Install C4 controllers in a central place for easy access and maintenance while drastically
reducing the amount of hardware required.
Have fun creating mesmerizing lighting installations!
The Acolyte and DiGidot teams

Page 3Acolyte is a quality division of GENLED Brands™| www.AcolyteLED.com |Acolyte | Architectural Lighting Solutions
INDEX
Introduction 4
Contents 4
Technical Drawings 5
Product Description 6
Before Installation 7
Installation & Wiring 8
Power Supply 9
Wiring Schemes 10
Connecting Power 11
Tips & Troubleshooting 12
General Information 12
Compliances 13

Page 4Acolyte is a quality division of GENLED Brands™| www.AcolyteLED.com |Acolyte | Architectural Lighting Solutions
INTRODUCTION
CONTENTS
SPI protocols are sensitive to data distortion and often only work safely over up to 6.5 ft
(2 m) of cable. The PxLNet Transceiver is a small module that can be used as a receiver or
transmitter to extend the range of an SPI signal. The PxLNet Transceiver converts PxLNet,
which is sent from a PxLNet Transmitter or Transceiver to the original SPI protocol that
is sent from a C4 controller. A PxLNet Transmitter or Transceiver converts sensitive SPI
protocols to PxLNet which can cover huge distances, up to 820 ft (250 m). Any single-
wire SPI protocol (Data only) can be received or be transmitted by this module. You can
connect the same number of universes to this receiver as to the C4 controller output port.
The onboard voltage regulator accepts voltages ranging from 5-24 VDC and can be powered
from the same power source as most pixel-controlled LED products. Installation is easy
thanks to the RJ45 connector. The output can also be soldered directly to most industry
standard SPI controlled LED strips. (If this module is soldered to the end of an LED strip or
pixel-controlled product, it can be used as a transmitter if the Tx/Rx jumper is removed.)
NOTE: We take great care with our products and have a standard of quality control, but we advise you to double-check for
missing or damaged items. In case of any missing or damaged items, please contact your supplier immediately. Never use
damaged products!
• PxLNet Transceiver module (PCB only)
• 3-pole screw terminal (optional, if requested at order)

Page 5Acolyte is a quality division of GENLED Brands™| www.AcolyteLED.com |Acolyte | Architectural Lighting Solutions
TECHNICAL SPECIFICATIONS
Electrical
Input Voltage: 5-24VDC
Max. power consumption: 1 W
Mechanical
Dimensions: 1.72 x 0.62 x 0.6 in. | 43.8 x 15.8 x 15.3 mm (L x W x H)
Net weight: 0.11 oz (6 g)
Environmental
Operation Temperature (Tc): 32 to 122°F (0 to 50°C)
Max. ambient Temp. (Tamax): 77°F (25°C)
Storage temperature: -4 to 122°F (-20 to 50°C)
Max. operating relative humidity: 90% (indoor use only)
Protection
IP rating: IP00 (unprotected, indoor use only)
DC input: Overvoltage protection (max. 60 VDC)
Connectivity
Solder pad wiring: 20-24 AWG (0.3-0.5 mm2)
Terminal wiring: Recommended: 20-24 AWG (0.3-0.5 mm2)
Max. 14 AWG (2.5 mm2)
Quality
Warranty: 1 year factory warranty
Compliances: CE, RoHS
Applied standards: EN60950-1:2006 +A11:2009 + A1:2010 + A12:2011
+ A2:2013, EC60950-1 / EN60950-1, EN61006-6-3,
EN55032
HS Code: 8537109090

Page 6Acolyte is a quality division of GENLED Brands™| www.AcolyteLED.com |Acolyte | Architectural Lighting Solutions
PRODUCT DESCRIPTION
0.6 in.
(15.3 mm)
0.62 in.
(15.8 mm)
1.72 in.
(43.8 mm)
1. Power (GND/DC-)
2. BUS I/O (Data Out)
3. Power (DC+ / 5-24 V)
4. Jumper (Ground lift)
5. Jumper (Tx / Rx mode)
6. RJ45 (Data input)
Topside
Bottomside
7. Power (DC+ / 5-24 V)
8. BUS I/O (Data Out)
9. Power (GND/DC-)
10. BUS I/O (Data + In)
11. BUS I/O (Data - In)
Pin 1: Orange/White = (DMX) Data +
Pin 2: Orange = (DMX) Data -
Pin 3: --
Pin 4: --
Pin 5: --
Pin 6: --
Pin 7: Brown/White = (DMX) GND/DC -
Pin 8: Brown = (DMX) GND/DC
0.98 in.
(25 mm)
2.56 in.
(65 mm)
2.56 in. (65 mm)
0.59 in.
(15.5 mm)
0.37 in.
(9.5 mm)

Page 7Acolyte is a quality division of GENLED Brands™| www.AcolyteLED.com |Acolyte | Architectural Lighting Solutions
BEFORE INSTALLATION
Before installing our products it’s important to note the following safety and installation
instructions.
SAFETY INSTRUCTIONS
• Before installation and use of this product, read this manual carefully.
• Make sure these instructions are given to those responsible for installation, use and
maintenance of this product.
• Local electrical and safety rules and guidelines always overrule this manual.
• Acolyte and DiGidot Technologies B.V. cannot be held liable for improper handling,
product installation, usage or storage.
• Installation should only be done by a professional certied installer who is qualied to
work on electrical installations.
• Do not conduct any repairs of the device (there are no user serviceable parts inside). Any
unapproved repairs and/or product modications will void product warranty. Acolyte
and DiGidot Technologies B.V. cannot be held liable for any consequences.
• Repairs of this product may only be carried out by DiGidot Technologies B.V.
• Repairs and maintenance of the installation may only be carried out by qualied
technicians.
• Always disconnect the mains power when working on a high voltage electric installation.
Failure to do so may result in product damage or personal injury.
• Do not connect or modify this product other than as described in this manual.
• Never use a product that is visibly damaged or does not work correctly. Never use a
product if it starts to smoke or if a crackling/sizzling noise is audible. If this is the case,
disconnect the power to the device and contact Acolyte immediately.
• This is a low voltage device. The working voltage is 5-24 VDC.
• The only way to power off this product is to disconnect it from the power source.
• The product is designed for indoor use (dry locations) only. Exposure to rain or moisture
may cause fatal damage.

Page 8Acolyte is a quality division of GENLED Brands™| www.AcolyteLED.com |Acolyte | Architectural Lighting Solutions
INSTALLATION AND WIRING
Mounting options
We recommend placing this product in a protected enclosure such as a junction box.
Double-sided (foam) tape may be used on the underside of this product to secure it.
Please be careful when applying pressure; small components can come off when applying
excessive force.
When using heat shrink, please cover the entire module and be careful when applying heat,
especially with heat guns. When overheating this product, components and soldering may
come loose, resulting in fatal damage.
WARNING!
• This product should not be subjected to higher temperatures than indicated in the
specication range (risk of fatal damage)!
• Keep this product away from direct sunlight, rain or other moisture (short-circuit risk).
• Do not use this product outdoors or in humid environments (short-circuit risk).
WARNING! TAKE ESD SAFETY PRECAUTIONS!
When working with PCB modules such as this product, you must work according to ESD
guidelines and undertake all necessary ESD safety precautions to minimize the risk of ESD-
inicted product damage.
TIP: It is safe to use and cover this product with appropriate electronic protection resin to improve IP rating. Another option to
improve the IP rating is to use a conformal coating spray for electronics after all wires have been connected.
There are several ways to connect and integrate this receiver module. You can use the RJ45
connector on the signal input side or solder your signal wires to the underside of the product.
Please refer to the wiring schemes in this manual.
DATA IN
Use the RJ45 bus to connect a Cat-5E network cable or better …
or ...
Solder a DMX cable (110Ω impedance) or Cat-5E or better to the D+ and D- solder pads on the
underside of the PCB. Solder the ground wire to the GND solder pad.

Page 9Acolyte is a quality division of GENLED Brands™| www.AcolyteLED.com |Acolyte | Architectural Lighting Solutions
To power this product, the DC+ and GND must be connected to a SELV rated power supply
that provides appropriate power at the required supply voltage.
Before connecting power, make sure that the outputs are wired and soldered correctly to
avoid short circuits.
WARNING: This product has no reverse polarity protection. Connecting/applying voltage
incorrectly will cause fatal damage!
IMPORTANT: Make sure to equalize the ground potentials. Always connect grounds (DC-) of
the C4 controller and every power supply connected to each product that is controlled by a
single C4 controller to each other. If the grounds are not connected, malfunctions may occur.
NOTE: Wires between the output and LED product should be within 6.5 ft (2 m) in length. The ground output wire from the
PxLNet Transceiver and Data wire must be equal in length.
POWER SUPPLY
CONNECTING POWER
DATA OUT & POWER IN
Solder this module directly to the solder pads of any pixel ribbon with a matching solder pad
layout …
or …
Solder wires with a wire gauge of 20-24 AWG (0.3-0.5 mm2) to GND, D, and 5-60V.
GND = Ground D = Data signal
5-24V = DC+ supply voltage
If you have ordered screw terminal(s) for the PxLNet Transmitter, you can solder the 3-pole
terminal to the output by placing the terminal on the top side of the PCB. Insert the 3 pins in
the solder pad holes and make sure the wire openings face outwards. Solder the pins on the
underside. The screw terminal allows you to insert the connection wires of your LED product
with wire gauges up to max. 14 AWG (2.5 mm2).

Page 10Acolyte is a quality division of GENLED Brands™| www.AcolyteLED.com |Acolyte | Architectural Lighting Solutions
WIRING SCHEMES
The following wiring schemes show assorted options to connect this product.
WIRING SCHEME 1
C4 controller with PxLNet Transmitter connected by Cat-5E network cables to PxLNet
Transceivers that are soldered directly to a pixel-controlled LED ribbon.
WIRING SCHEME 2
PxLNet Transmitter connected by Cat-5E network cables that are soldered to PxLNet
Transceivers and output wires that are soldered to LED products.
C4 Controller
LEDs Cat-5 E cable
max. 820 ft. (250 m)
PxLNet Transceiver PxLNet Transmitter
- +
5-48V DC
LEDs
- +
Ethernet
Ethernet
C4 Controller
Cat-5 E cable
max. 820 ft. (250 m)
PxLNet Transceiver PxLNet Transmitter
- +
5-48V DC