Genmitsu 3018-PROVer User manual

V1.3 Mar.2022
USER MANUAL
Genmitsu
CNC Router 3018-PROVer
Contents / コンテンツ
English
日本語
01 - 40
41 - 80
CNC ルーター 3018-PROVer
日本語組み立て説明書

Welcome
Disclaimer
Part 1 - Unboxing
Part 2 - Mechanical installation
Part 3 - Wiring
Part 4 - Software Setup
Part 5 - Using Offline Controller
Part 6 - Troubleshooting
01
02
03
07
21
39
39
40
..........................................................................................................................................
.......................................................................................................................................
...........................................................................................................................
.................................................................................................................
.................................................................................................................................
...................................................................................................
.................................................................................................
..............................................................................................................
Contents

01
Thank you for purchasing the Genmitsu 3018-PROVer CNC Router from SainSmart.
Included in your package will be a Micro SD card. On the Micro SD Card, you will find:
These files can also be downloaded from SainSmart Online Resource Center
https://docs.sainsmart.com/3018-prover
[e-mail].
Welcome
Scan QR code
to join the group
, https://www.facebook.com/groups/SainSmart.GenmitsuCNC).

02
this manual.
connected with the assembly, handling, storage, use, or disposal of the product.
Please be careful when using your CNC machine. This machine is an electrical device with moving parts and
dangerous areas.
power supply; it may cause malfunctions or damage to the machine.
Disclaimer

03
1
5
10 11
Offline Controller
6 7 8
9
3 4
Power Supply
[e-mail].
Part 1 - Unboxing

04
Offline Controller Cable
13
Spindle Cable, 35cm
30
14
15
16
17
18
19
29
30
17# ER11 Schraubenschlüssel
13# ER11 Schraubenschlüssel

05
Spacer Template Tool
31
39
33
36 Cable Protector
49
37 38
MicroSD Card MicroSD Card
Reader 40
41
43
44
45
46
34
35
47
48 Spacer
V1.2 May 2020
USER MANUAL
Genmitsu CNC Router 3018-PROVer

06
Optional Accessories (Not Included)
Consider following optional upgrades or accessories to make your CNC experience better!
You can find them on www.sainsmart.com. Save 10% with discount code PROVER10
5.5W Laser Module
CNC Router Bits Essential Kit
6Pcs Micro Limit Switches
with 1M 3 Pin Cable
GS-775MR 24V 20,000
RPM Spindle with ColletCNC MDF Spoilboard
3040 Y-Axis Extension Kit
Resin Board for CNC
Engraving, 2-Pack
Scan QR codes to learn more
Acrylic Sheet for CNC,
180 x 100 x 5mm,
4-Pcs

07
43 5mm
2.1 Preparing your base assembly
What you will need
Step 1:
from the bearing mount.
Step 2:
screw mount as shown in the picture.
Step 3:
to secure the lead screw mount.
Part 2 - Mechanical installation

08
Step 1:
Step 2:
45
2.2 Installing limit switches & cable holders to Y-Axis
What you will need
33 30
M3 5mm

09
Step 3: Install one limit switch on each side by tightening the M3 5mmscrews.

10
40 3mm
Step 1:
2.3 Installing Rubber feet to Y-Axis Base Assembly
What you will need

11
1
3049
2.4 Installing Limit Switches to X-Axis/Z-Axis Gantry
What you will need
44
45
33

12
Step 1:
Step 2: Install four cable holders on the same side of the gantry. Two on the inside and two on the outside.
Step 3:
this limit switch.

13
Step 1:
assembly so that the step motor
is facing your right hand side.
Step 2:
Nuts on each side. Position near
the back of the machine (Stepper
Step 3:
Template into the slot and space
out the T-slot nuts as shown in
the picture.
2.5 Install T-Slot Tension Nuts
What you will need
Spacer Template Tool
31
Allen Wrench, 4mm
28

14
1
Spacer Template Tool
31
2.6 Install Y-Axis Base toX/ZAxis Gantry
What you will need
4mm
Step 1:
Step 2:

15
Step 3:
until you finish the other side.
Step 4:
screws.

16
2.7 Install the Spindle
What you will need
33mm 4
Step 1:
Then screw the the collet collar back to the spindle.

17
Step 2:
Step 3:
Step 4:

18
2.8 Install the Acrylic Baffles
What you will need
3mm
41 48 5
right baffle first, by placing the baffle along
side the frame to fit the shape. Peel off the
Step 1: Insert the M5 bolts from the outside
baffle, the M5 bolt should insert from the left
from the other side using your hand. One
the T-Slot nuts horizontally.
Step 2: Place T-Slot nuts into the side of the
machine so that the baffle is aligned with the
edge of the frame.