George's 650W User manual

CYCLONE WALL FANS
Model Numbers: 650W, 750W
INSTRUCTION MANUAL
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE

OPERATING INSTRUCTIONS
Packaging
Please DO NOT dispose of any packaging until you have checked the
appliance is operational.
After removing the packaging ensure the contents are intact and complete.
In the unlikely event of missing part, contact your retailer.
DO NOT leave children unattended with any oft he packaging since it is a
potential source of danger. Disposal of all packaging must be carried out
responsibly & safely and in accordance with your local authority regulations.
ALWAYS recycle the packaging material where possible.
When using any electrically powered product, basic safety precautions
should always be followed.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE
SAFE OPERATIONAL REQUIREMENTS, WARNINGS, AND CAUTIONS. USE
THIS PRODUCT CORRECTLY, AND WITH CARE FOR THE PURPOSE FOR WHICH
IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY.
Page 1

GENERAL INFORMATION
WARNING -to reduce the risk of fire, electrical shock or injury to persons or
property:
1. Always operate the product from a power source of the same voltage, frequency and rating as
indicated on the product identification plate.
2. Close supervision is necessary when any product is used by or near children the elderly or the in
firm. Do not allow children to use the appliance as a toy.
3. Do not operate any product with a damaged power cord or plug, after the product malfunctions,
dropped or damaged in anyway. Return the complete product to the place of purchase for
inspection, repair or replacement.
4. To reduce the risk of electric shock, do not expose the unit or flexible cord to moisture of any kind.
5. Switch off and unplug from the power socket when not in use, before assembling or before
cleaning.
6. Do not place objects on the product or allow objects to obstruct the inlet or outlet openings, or
operate in close proximity to walls or curtains, etc.
7. The use of attachments or accessories not recommended or sold by the product distributor may
cause injury to persons or damage to property.
8. This product is intended for normal light commercial use only.
9. Do not attempt to dismantle the appliance.
10. Do not operate the appliance on a metal surface.
11. Do not use the appliance in artificially hot or humid conditions or allow to be used in a hazardous
environment.
12. Do not clean the appliance with organic solvent. This appliance is not intended for use by
persons(including children) with reduced physical, sensory or mental capabilities, or lack of
experience and knowledge unless they have been given supervision or instruction concerning use
of the appliance by a person responsible for their safety. Children should not be left unsupervised
with the appliance.
13. This instruction manual is an integral part of the appliance and should be stored for safe keeping
and must always accompany the appliance in the event of ownership transfer or for reference to by
a service engineer.
Page 2

INTRODUCTION AND SPECIFICATION
The Cyclone wall mounted fans are designed for use in a wide variety of industrial, commercial
and agricultural applications.
Whether it is for industrial warehousing, gymnasiums, factories, marquees or workshop
applications, or comfort cooling within agricultural buildings for livestock, Cyclone Wall mounted
fans provide powerful, cool, yet effective, positive air movement, there by improving the
environmental conditions for both humans and animals.
Page 3

Operation
Page 4
Upon receipt, the fan equipment should be visually inspected to check for any damage.
Check the details on the motor rating plate to ensure that the correct power supply (voltage, frequency and phase)
is available. An incorrect power supply will lead to permanent damage to the fan motor.
Wall fan –Securely fix the wall plate to a structurally sound wall using suitable fasteners. Ensure that the wall and
wall plate are able to support the cantilevered fan weight. Fit the wall bracket into the wall plate and lock in
position.
Loosen the set screw in the motor mounting flange. Engage the motor support flange in the mounting flange and
tighten the set screw.
Take apart the guard front cover from the rear cover, and securely fasten the guard rear cover to the motor using
the four screws provided.
Fit the impeller to the motor shaft ensuring that the locking screw is securely fastened.
Fit the guard front cover to the rear cover using the clips and screw.
Check that all fasteners are tight and that the impeller rotates freely.
Secure the cable, ensuring that a generous loop of cable is allowed between the cable anchorage point and the
motor. This is to prevent excessive flexure of the cable caused by repetitive oscillation of the fan.

Page 6
Start-up
WARNING The fan must be isolated from the power supply before adjusting any operating
conditions apart from altering the fan speed. The angle of tilt of the fan motor axis must not exceed
30 Degrees from the horizontal to avoid straining the oscillation mechanism.
Before power is supplied to the unit, ensure that the impeller is free to rotate.
Check that the motor amperage draw does not exceed the nameplate rating.
Speed - The fan has three speed settings, 1 –3, with 0 being the off position.
Oscillation - There are two adjustment settings to the oscillation plate. If the adjustment screw is set
to the middle of the oscillating plate, the fan will not oscillate. If the adjustment screw is not
positioned in the middle of the oscillation plate, the fan will oscillate through 90 degrees.
Airflow Direction - To change direction of airflow, hold the fan stationary and loosen the locking knob.
Rotate the motor to a suitable position and then re-tighten the locking knob. It is not necessary to
move the base frame.
Angle of Tilt - Hold the fan stationary and loosen the head holding screw. Adjust the angle of tilt and
re-tighten the screw.

GENERAL MAINTENANCE
Page 5
Inspect ion of fan at least once every 12 months is recommended to ensure that the motor, fan
blades, and supporting guards, are clean. Any build up of dust and deposits on the blades guards
should be removed using a non-abrasive cleaner.
All fastenings should be checked for tightness. In addition, all rotating items should be checked.
Bearings are lubricated for life and will not need a detailed inspection.
WARNING The fan is fitted with an auto-reset thermal contact which switches the fan off in the
event of a fault condition. Once the motor cools down the fan may start unexpectedly. Only a
suitably qualified and competent person may carry out maintenance after the electrical supply
has been isolated
TECHNICAL DATA
BS Plug Wiring
Wiring Instructions: Should it be necessary to change the plug
please note the wires in the mains lead are coloured in accordance
with the following code:
BLUE ‐NEUTRAL
BROWN ‐LIVE
GREEN AND YELLOW ‐EARTH
As the colours of the wires in the mains lead of this appliance may
not correspond with the coloured markings identifying the terminals
in your plug, proceed as follows:
1. The BLUE wire is the NEUTRAL and must be connected to the
terminal that is marked with the letter N or coloured BLACK.
2. The BROWN wire is the LIVE and must be connected to the
terminal that is marked with the letter L or coloured RED.
3. Neither wire is to be connected to the terminal which is marked
with the letter E or earth symbol, coloured GREEN or
GREEN/YELLOW.
4. Always ensure that the cord grip is positioned and fastened
correctly. If a 13A(BS1363) fused plug is used it must be fitted with a
13A(BS1362) fuse. If in doubt consult a qualified electrician.
Wiringfora13Ampplug(BS1363)
The Earth Terminal is marked with the letter E or Earth Symbol

WARRANTY
Page 6
ONE (1) YEAR LIMITED WARRANTY
Retain this warranty information
George’s Industrial Services undertakes to replace or repair at its discretion goods (excluding
batteries) should they become defective within one year solely as a result of faulty materials
& workmanship.
If the product has been: used inappropriately; not been maintained or if any attempt has
been made to rectify, dismantle or alter the appliance in any way the warranty will be invalid.
Any modifications to the fan or its installation, even the smallest modification, change or
elimination of security components or pieces that influence the efficiency or loss of
ventilation, will result in the CE Certification warranty being cancelled.
If the unlikely event of a fault, the appliance must be returned to the point of sale with proof
of purchase and a FULL description of the fault.
In the unlikely event of a problem, please contact our help desk 0208 207 2455
This product has been manufactured to comply with EEC directives 2006/95/EG & 89/336/EEC
Electrical products should not be disposed of with general household waste. Please recycle
where facilities exist.
For more information on disposal contact your local authority.