GeoVision GV-Fisheye SERIES User manual

Quick Start Guide
GV-Fisheye IP Camera
© 2014 GeoVision Inc.All rights reserved.
Thank you for purchasing GV-Fisheye IP Camera. This guide is designed to
assist the new user in getting immediate results from the GV-Fisheye IP
Camera. For advanced information on how to use the GV-Fisheye IP Camera,
please refer to GV-Fisheye IP Camera User's Manual on Software DVD.
FE-QG-G

© 2014 GeoVision, Inc. All rights reserved.
Under the copyright laws, this manual may not be copied, in whole or in part,
without the written consent of GeoVision.
Every effort has been made to ensure that the information in this manual is
accurate. GeoVision, Inc. makes no expressed or implied warranty of any kind
and assumes no responsibility for errors or omissions. No liability is assumed
for incidental or consequential damages arising from the use of the information
or products contained herein. Features and specifications are subject to
change without notice.
Note:
1. GV-FE110 / FE420 / FE520 are excluded from Japan, EU and German
market.
2. No memory card slot or local storage function for Argentina.
GeoVision, Inc.
9F, No. 246, Sec. 1, Neihu Rd.,
Neihu District, Taipei, Taiwan
Tel: [phone]
Fax: [phone]
http://www.geovision.com.tw
Trademarks used in this manual: GeoVision, the GeoVision logo and GV
series products are trademarks of GeoVision, Inc. Windows and Windows XP
are registered trademarks of Microsoft Corporation.
June 2014

Contents
Naming and Definition ..........................................................................iii
Note for Connecting to GV-System .....................................................iv
Note for Recording.................................................................................v
Note for USB Storage and WiFi Adapter.............................................vi
Note for Installing Camera Outdoor ...................................................vii
Optional Accessories............................................................................ix
1. Introduction......................................................................................1
1.1 Packing List..............................................................................................................2
1.2 Overview...................................................................................................................7
2. Installation......................................................................................11
2.1 Hard Ceiling Mount.................................................................................................11
2.2 In-Ceiling Mount .....................................................................................................15
2.3 Wall Mount and Ground Mount...............................................................................18
3. Connecting the Camera ................................................................19
3.1 GV-FE110 / 111 / 2301 / 420 / 421 / 4301 / 520 / 521............................................19
3.2 GV-FER521............................................................................................................21
3.3 GV-FE2302 / 2303 / 3402 / 3403 / 4302 / 4303 / 5302 / 5303................................22
3.4 Connecting PoE Converter and IR LED Ring for GV-FE2303 / 3403 / 4303 / 5303...
...............................................................................................................................23
3.5 GV-FER3402 / 3403 / 5302 / 5303.........................................................................25
4. Accessing the GV-Fisheye Camera .............................................28
4.1 Web Browser..........................................................................................................28
4.2 Looking Up the Dynamic IP Address......................................................................29
4.3 Configuring the IP Address.....................................................................................31
4.4 Configuring the Wireless Connection.....................................................................33
i

5. The Web Interface..........................................................................36
5.1 Fisheye View..........................................................................................................38
6. Upgrading System Firmware........................................................41
7. Restoring to Factory Default ........................................................42
7.1 Using the Web Interface.........................................................................................42
ii
7.2 Directly on the Camera...........................................................................................43

Naming and Definition
GV-System GeoVision Analog and Digital Video Recording Software. The
GV-System also refers to Multicam System, GV-NVR System,
GV-Hybrid DVR System and GV-DVR System at the same time.
iii

Note for Connecting to GV-System
The GV-Fisheye IP Camera is designed to work with GV-System, a hybrid or digital video
management system. Note the following when the camera is connected to GV-System:
1. By default, the images are recorded to the memory card inserted in the GV-Fisheye IP
Camera.
2. Once the camera is connected to the GV-System, the resolution set on the GV-System
will override the resolution set on the camera’s Web interface. You can only change the
resolution settings through the Web interface when the connection to the GV-System is
interrupted.
iv

Note for Recording
1. By default, the images are recorded to the memory card inserted in the GV-Fisheye IP
Camera. Make sure the Write recording data into local storage option is enabled. If this
option is disabled, the camera will stop recording to the memory card while the live view is
accessed through Web browsers or other applications. For details, see Video Settings,
Administrator Chapter, GV-Fisheye IP Camera User’s Manual on the Software DVD.
2. Mind the following when using an inserted memory card for recording:
Recorded data on the memory card can be damaged or lost if the data are accessed
while the camera is under physical shock, power interruption, memory card
detachment or when the memory card reaches the end of its lifespan. No guarantee is
provided for such causes.
To avoid power outage, it is highly suggested to apply a battery backup (UPS).
For better performance, it is highly suggested to use Micro SD card of MLC NAND
flash, Class 10.
Replace the memory card when its read/write speed is lower than 6 MB/s or when the
memory card is frequently undetected by the camera.
v

Note for USB Storage and WiFi Adapter
Mind the following limitations and requirements for using USB storage and GV-WiFi Adapter:
1. The USB hard drive must be of 2.5’’ or 3.5’’, version 2.0 or above.
2. The USB hard drive’s storage capacity must not exceed 2TB.
3. USB flash drives and USB hubs are not supported.
4. External power supply is required for the USB hard drive.
vi
5. To connect a GV-WiFi Adapter, make sure it is connected before the camera is powered
on.

Note for Installing Camera Outdoor
When installing GV-FER outdoor models, be sure that:
1. The camera is set up above the junction box to prevent water from entering the camera
along the cables.
2. Any PoE, power, audio and I/O cables are waterproofed using waterproof silicon rubber or
the like.
vii
3. The screws are tightened and the cover is in place after opening the camera cover.

4. An operating IR LED ring may reach high temperatures of up to 60°C (140°F). Disconnect
the power supply and allow the IR LED ring to cool down before handling the device.
IR LED Ring
5. The silica gel bag loses it effectiveness when the dry camera is opened. To prevent the
lens from fogging up, use the supplied adhesive tap and replace the silica gel bag every
time you open the camera, and conceal the gel bag in camera within 2 minutes of
exposing to open air.
viii
6. For each newly replaced silica gel bag, allow it to absorb moisture for at least 5 hours
before operating the camera.

ix
Optional Accessories
Optional devices can expand the capabilities and versatility of your GV-Fisheye Camera.
Contact your dealer for more information.
Name Details
GV-PA191
Power over Ethernet (PoE)
Adapter
The GV-PA191 is a Power over Ethernet (PoE) adapter
designed to provide power to the IP device through a single
Ethernet cable.
GV-Mount Accessories The GV-Mount Accessories provides a comprehensive lineup
of accessories for installation on ceiling, wall and pole. For
details, see GV-Mount Accessories Installation Guide on the
software DVD.
GV-WiFi Adapter The GV-WiFi Adapter is a plug-and-play device that provides
WiFi connectivity to GV-IP Cameras through a mini USB port.
This product complies with IEEE 802.11 b/g/n (Draft 3.0)
standards for wireless networking.
GV-POE Switch The GV-POE Switch is designed to provide power along with
network connection for IP devices. The GV-POE Switch is
available in various models with different numbers and types
of ports.
Power Adapter for GV-IR
LED Ring
The power adapter is available in 6 regions: Argentina,
Australia, Brazil, Europe, U.K and U.S.
Power Adapter for
GV-Fisheye Camera
The power adapter is available in 6 regions: Argentina,
Australia, Brazil, Europe, U.K and U.S.

1. Introduction
Welcome to the GV-Fisheye IP Camera Quick Start Guide. In the following sections, you will
learn the basic installations and configurations of the GV-Fisheye IP Cameras listed below.
For a detailed user manual, see the GV-Fisheye IP Camera User’s Manual on the
GV-Fisheye IP Camera Software DVD.
Note: Only GV-FER3402 / 3403 / 521 / 5302 / 5303 are for outdoor use.
1

1.1 Packing List
GV-FE110 / 111 / 420 / 421 / 520 / 521 / 2301 / 4301 and GV-FER521
2
Fisheye Camera
Support Bracket x 3
Camera Cover (Hard Ceiling Mount)
Camera Cover (In-Ceiling Mount)
Screw (Hard Ceiling Mount) x 3
Screw (In-Ceiling Mount) x 3
Torx Wrench
Plastic Screw Anchor x 3
Installation Sticker GV-Fisheye IP Camera Software DVD
GV-NVR Software DVD GV-NVR Quick Start Guide
For GV-FE110 / 111 / 420 / 421 / 520 / 521 / 2301 / 4301 only:
- 3-Pin or 2-Pin Terminal Block
- DC 12V Power Adapter
For GV-FER521 only:
- Cable Connector
- Silica Gel Bag and Adhesive Tape x 2

GV-FE2302 / 3402 / 4302 / 5302 and GV-FE2303 / 3403 / 4303 / 5303
3
Fisheye Camera
Support Bracket x 3
Camera Cover (Hard Ceiling Mount)
Camera Cover (In-Ceiling Mount)
Screw (Hard Ceiling Mount) x 3
Screw (In-Ceiling Mount) x 3
Torx Wrench
Plastic Screw Anchor x 3
Mini USB Extension Cable
IR LED Ring (GV-FE2303 / 3403 /
4303 / 5303 only)

PoE Converter set (including 1 module, 1 DC Power Y-cable, 1 RJ-45 cable and 3
screws) (GV-FE2303 / 3403 / 4303 / 5303 only)
Installation Sticker
GV-Fisheye IP Camera Software DVD
GV-NVR Software DVD
GV-NVR Quick Start Guide
4

GV-FER3402 / 5302 and GV-FER3403 / 5303
5
Fisheye Camera
Support Bracket x 3
Camera Cover (Hard Ceiling Mount)
Camera Cover (In-Ceiling Mount)
Screw (Hard Ceiling Mount) x 3
Screw (In-Ceiling Mount) x 3
Torx Wrench
Plastic Screw Anchor x 3
IR LED Ring (GV-FER3403 / 5303 only)
Waterproof Rubber

Power Cable Terminal Block x 2
(female) (male)
IR Power Adapter (GV-FER3403 / 5303
only)
Installation Sticker
Silica Gel Bag and Adhesive Tape x 2 Cable Connector
GV-Fisheye IP Camera Software DVD GV-NVR Software DVD
GV-NVR Quick Start Guide
6

1.2 Overview
GV-FE110 / 111 / 420 / 421 / 520 / 521 / 2301 / 4301 and GV-FER521
To access the Default button, LED indicators and micro SD card slot, unscrew the screws
indicated below and then remove the camera cover.
GV-FE110 / 111 / 2301 / 420 / 421 / 4301 /
520 / 521. GV-FER521 GV-FER521
You can now access the Load Default button, LED indicators, and the micro SD card slot.
GV-FE110 / 111 / 420 / 421 / 520 / 521 / 2301 / 4301:
6
5
7
8
2
4
3
1
7

GV-FER521:
1
2
3
57 8 4
6
No. Name Function
1 Lens Receives image inputs.
2 Speaker Talks to the surveillance area from the local computer.
3 Microphone Receives the sound from the camera.
4 Default Button Resets all configurations to default factory settings. See 7.
Restoring to Factory Default in the Quick Start Guide.
5 Micro SD Card Slot Inserts a micro SD / SDHC memory card to store recorded
data.
6 Network status LED Indicates the network status.
7 Power status LED Indicates whether the camera is powered on or off.
8 System status LED Indicates whether the system is booted successfully or not.
Note: SDXC and UHS-I card types are not supported.
8

GV-FE2302 / 2303 / 3402 / 3403 / 4302 / 4303 / 5302 / 5303
1
2
3
No. Name Function
1. Lens Receives image inputs.
2. Speaker Talks to the surveillance area from the local computer.
3. Microphone Receives the sound from the camera.
4. Status LED Indicates whether the device is booted successfully or not.
5. LAN / PoE Connects to a 10/100 Ethernet or PoE.
6. Terminal Block Connects to power.
7. Default Button Resets all configurations to default factory settings. See 7.
Restoring to Factory Default in the Quick Start Guide.
8. Audio Out Connects to an external speaker for broadcast.
9. Micro SD Card Slot Inserts a micro SD / SDHC memory card to store recorded
data.
10. Mini USB Slot Connects to a GV-WiFi Adapter or a USB hard drive for
external storage.
Note: SDXC and UHS-I card types are not supported.
9