geratech EGE-HD-541FS User manual

EGE-HD-541FS
5×1 HDMI/MHL Fast Switcher, IR, RS232 Controll

EGE-HD-541FS
5×1 HDMI/MHL Fast Switcher, IR, RS232 Controll

EGE-HD-541FS
5×1 HDMI/MHL Fast Switcher, IR, RS232 Controll
DISCLAIMERS
The information in this manual has been carefully checked and is believed to be accurate.
Geratech assumes no responsibility for any infringements of patents or other rights of third
parties which may result from its use.
Geratech assumes no responsibility for any inaccuracies that may be contained in
this document. Geratech also makes no commitment to update or to keep current the
information contained in this document.
Geratech reserves the right to make improvements to this document and/or product at any
time and without notice.
COPYRIGHT NOTICE
No part of this document may be reproduced, transmitted, transcribed, stored in a retrieval
system, or any of its part translated into any language or computer le, in any form or by
any means—electronic, mechanical, magnetic, optical, chemical, manual, or otherwise—
without express written permission and consent from Geratech.
© Copyright 2011 by Geratech.
All Rights Reserved.
Version 1.1 August 2011
TRADEMARK ACKNOWLEDGMENTS
All products or service names mentioned in this document may be trademarks of the
companies with which they are associated.

EGE-HD-541FS
5×1 HDMI/MHL Fast Switcher, IR, RS232 Controll
SAFETY PRECAUTIONS
Please read all instructions before attempting to unpack, install or operate this equipment
and before connecting the power supply.
Please keep the following in mind as you unpack and install this equipment:
• Always follow basic safety precautions to reduce the risk of re, electrical shock and
injury to persons.
• To prevent re or shock hazard, do not expose the unit to rain, moisture or install this
product near water.
• Never spill liquid of any kind on or into this product.
• Never push an object of any kind into this product through any openings or empty slots
in the unit, as you may damage parts inside the unit.
• Do not attach the power supply cabling to building surfaces.
• Use only the supplied power supply unit (PSU). Do not use the PSU if it is damaged.
• Do not allow anything to rest on the power cabling or allow any weight to be placed
upon it or any person walk on it.
• To protect the unit from overheating, do not block any vents or openings in the unit
housing that provide ventilation and allow for sufcient space for air to circulate around
the unit.
REVISION HISTORY
VERSION NO. DATE DD/MM/YY SUMMARY OF CHANGE
VS1 29/03/13 First Release

EGE-HD-541FS
5×1 HDMI/MHL Fast Switcher, IR, RS232 Controll
CONTENTS
1. Introduction............................................................................... 1
2. Applications .............................................................................. 1
3. Package Contents .................................................................... 1
4. System Requirements.............................................................. 1
5. Features..................................................................................... 2
6. Operation Controls and Functions ......................................... 3
6.1 Front Panel............................................................................ 3
6.2 Rear Panel............................................................................. 4
6.3 Remote Control ..................................................................... 5
6.4 RS-232 Protocol .................................................................... 6
6.5 Remote Command Protocol .................................................. 7
7. Connection Diagram ................................................................ 8
8. Specications ........................................................................... 9
9. Acronyms .................................................................................. 9

EGE-HD-541FS
5×1 HDMI/MHL Fast Switcher, IR, RS232 Controll
1
1. INTRODUCTION
The 5 by 1 HDMI/MHLTM Fast Switcher has MHL (Mobile High-Denition Link) interface
integrated on its fth input which can be used to share high denition video and audio from
any of your MHL-ready mobile devices on an HDTV, and simultaneously charge the device
whilst connected. The switcher supports 3D signal up to 2.25Gbps bandwidth, 12-bit Deep
Color, Hi-Def lossless audio and other features dened by HDMI specications, on all of
its 5 input. Source selection can be easily controlled through on-panel buttons, IR remote
control or by RS-232 protocol.
2. APPLICATIONS
• Smart home entertainment
• Show room or meeting room
• Smart AV installation
• Mobile device integration
3. PACKAGE CONTENTS
• 1× 5 by 1 HDMI/MHL Fast Switcher
• 1×5V DC Power Adaptor
• 1×IR Extender Cable
• 1×MHL to HDMI Cable
• 1×Remote Control with Battery (CR-113)
• Operation Manual
4. SYSTEM REQUIREMENTS
• HDMI sources such as PS3 or Blu-ray players for ports 1 to 5 using standard HDMI
cabling. The fth port can be connected to an MHL-ready mobile device with an MHL to
HDMI cable.
• HDMI equipped display.

EGE-HD-541FS
5×1 HDMI/MHL Fast Switcher, IR, RS232 Controll
2
5. FEATURES
• Supports InstaPortTM Technology
• Supports ve HDMI input ports, the fth port is an HDMI/MHL port
• Supports one HDMI output
• Supports video resolutions up to 1080p@60 Hz
• Supports HDMI specication features, including data rates up to 2.25Gbps and12-bit
Deep Color
• Supports 3D signal
• MHL port supports 1080p@30 Hz or 1080i@60 Hz resolutions
• MHL port supports charging of a connected mobile device

EGE-HD-541FS
5×1 HDMI/MHL Fast Switcher, IR, RS232 Controll
3
6. OPERATION CONTROLS AND FUNCTIONS
6.1 Front Panel
5X1 HDMI/MHL FAST SWITCHER CFSW-51MHL
54321
POWER
INPUT
1 2 3
1IR Receiver
Supports reception of IR codes from the system's IR remote control only.
2INPUT Buttons and LEDs
Press the 'INPUT' source button to select the required input source, the blue LED will
indicate the selected source.
3POWER Button and LED
Press this button to switch the device 'ON' or press it again to put it into standby mode.
When the system is on the green LED will illuminate.

EGE-HD-541FS
5×1 HDMI/MHL Fast Switcher, IR, RS232 Controll
4
6.2 Rear Panel
DC 5V
54321
MHL/HDMI
HDMI IN
HDMI OUT
RS232
IR IN
1 2 3 4 5
1IR IN
Connect to the supplied IR extender cable for receiving the IR remote signal for this
device only.
2RS232
Connect to a PC or control system with D-Sub 9-pin cable for RS-232 control. For RS-
232 commands please refer to section 6.4.
3HDMI OUT
Connect to LCD TV or HD monitor with an HDMI cable.
4HDMI IN
Connect HDMI sources to the HDMI inputs 1 to 5 such as DVD players, Blu-ray players,
PS3s or other sources with HDMI cables. The fth input can be used to connect to
HDMI or MHL-Ready mobile devices.
 Note:WhenanMHLdeviceisconnectedtothefthMHL-readyinputitwillbecharged
automatically.IftheMHLdeviceisswitchedoffwhenconnected,itwillbeturnedon
automatically.
5DC 5V
Connect the DC 5V power supply into the system and plug the adaptor to an AC wall
outlet.

EGE-HD-541FS
5×1 HDMI/MHL Fast Switcher, IR, RS232 Controll
5
6.3 Remote Control
1Power
Press this button to switch the device on or to put the device
into standby mode.
2HDMI 1~5
HDMI Input selection keys. Press a key to directly select that
input.
 Note:Forthismodelonlykeys1~5areactive.
3Mute/Vol +/Vol -
These buttons control the volume level or mute the audio
from the MHL mobile device or CEC-enabled source devices connected to MHL input
port.
4
These buttons can control what is playing on the MHL input source (including CEC-
enabled source devices or MHL mobile device), play/pause and track skip forward/
backwards.
 Note:InordertocontroltheMHLmobiledevice,thescreentime-outsettingmustbeset
to'OFF'.
5Input
Press this button to cycle through the input selections (from 1~5).
6Menu
Press this button to enter the input source's root menu (including CEC-enabled source
devices or MHL device).
7▲▼◄► & Enter
These buttons will control the input source's OSD menu selection.
 Note:Forthesystemtocontrolfunctions3~6,theinputsourcedevicemustbeanHDMI
CEC-enableddevicewithitsCECfeatureturnedon.Pleaserefertothemanualforthe
sourcedevicefortheinstructions.
8Exit
Press this button to exit the selection.
Menu Input
HDMI 1HDMI 2HDMI 3
HDMI 6
HDMI 4HDMI 5
Vol +
HDMI 7HDMI 8
Mute
Vol -
Exit
Enter
CR-113
1
2
4
5
7
3
6
8

EGE-HD-541FS
5×1 HDMI/MHL Fast Switcher, IR, RS232 Controll
6
6.4 RS-232 Protocol
CFSW-51MHL
►
◄
REMOTE CONTROL
Pin Assignment Pin Assignment
1 NC 1 NC
2 TxD 2 RxD
3 RxD 3 TxD
4 NC 4 NC
5 GND 5 GND
6 NC 6 NC
7 NC 7 NC
8 NC 8 NC
9 NC 9 NC
Baud Rate: 19200 bps
Data Bit: 8-bit
Parity: None
Flow Control: None
Stop Bit: 1-bit
COMMANDS ACTION
POWER 00 Power Off (standby)
POWER 01 Power On
PORT 01 Output Select Input 1
PORT 02 Output Select Input 2
PORT 03 Output Select Input 3
PORT 04 Output Select Input 4
PORT 05 Output Select Input 5
AUTO 00 AUTO switch off
AUTO 01 AUTO switch on
ISP 01 Software ISP process
RCP 00-7f RCP (remote command protocol) command
Note:TheRS-232commandswillnotbeacceptedunlessfollowedbyacarriagereturn.

EGE-HD-541FS
5×1 HDMI/MHL Fast Switcher, IR, RS232 Controll
7
6.5 Remote Command Protocol
Opcode Key Name Opcode Key Name Opcode Key Name
0x00 Select 0x2B Enter 0x4D-0x4F Reserved
0x01 Up 0x2C Clear 0x50 Angle
0x02 Down 0x2D-02xF Reserved 0x51 Subpicture
0x03 Left 0x30 Channel Up 0x52-0x5F Reserved
0x04 Right 0x31 Channel Down 0x60 Play Function
0x05 Right-Up 0x32 Previous
Channel
0x61 Pause_Play
Func.
0x06 Right-Down 0x33 Sound Select 0x62 Record
Function
0x07 Left-Up 0x34 Input Select 0x63 Pause_Record
Func.
0x08 Left-Down 0x35 Show Info 0x64 Stop Function
0x09 Root Menu 0x36 Help 0x65 Mute Function
0x0A Setup Menu 0x37 Page Up 0x66 Restore_
Volume Func.
0x0B Contents Menu 0x38 Page Down 0x67 Tune Function
0x0C Favorite Menu 0x39-0x3F Reserved 0x68 Select_Media
Func.
0x0D Exit 0x40 Reserved 0x69 Reserved
0x0E-0x1F Reserved 0x41 Volume Up 0x6A Reserved
0x20 Numeric 0 0x42 Volume Down 0x6B-0x70 Reserved
0x21 Numeric 1 0x43 Mute 0x71 F1
0x22 Numeric 2 0x44 Play 0x72 F2
0x23 Numeric 3 0x45 Stop 0x73 F3
0x24 Numeric 4 0x46 Pause 0x74 F4
0x25 Numeric 5 0x47 Record 0x75 F5
0x26 Numeric 6 0x48 Rewind 0x76-0x7D Reserved
0x27 Numeric 7 0x49 Fast Forward 0x7E Vendor_
0x28 Numeric 8 0x4A Eject Specic
0x29 Numeric 9 0x4B Forward 0x7F Reserved
0x2A Dot 0x4C Backward

EGE-HD-541FS
5×1 HDMI/MHL Fast Switcher, IR, RS232 Controll
8
7. CONNECTION DIAGRAM
DC 5V
54321
MHL/HDMI
HDMI IN
HDMI OUT
RS232
IR IN
OR
60°
MHL to
HDMI Input
HDMI Output
Power Supply
HDTV
HDMI
Input
HDMI
Input
RS-232
HDMI
Input
HDMI Input HDMI Input
Set-top Box
PC
Blu-ray Player
Satellite Receiver Media Player
Smartphone
Remote
IR Extender
RS-232 Equipped
PC or Notebook

EGE-HD-541FS
5×1 HDMI/MHL Fast Switcher, IR, RS232 Controll
9
8. SPECIFICATIONS
Video Bandwidth 225 MHz/6.75 Gbps
Input Ports 5×HDMI
Output Port 1×HDMI
Resolution Support VGA~WUXGA@60 (RB)
480i/p, 576i/p, 720p@50/60/120
1080i@50/60, 1080p@24/30/50/60
(MHL only supports 1080p@30 & 1080i@60)
ESD Protection Human body model:
±8 kV (air-gap discharge)
±4 kV (contact discharge)
Power Supply 5 V/2.6 A DC (US/EU standards, CE/FCC/UL
certied)
Dimensions 240 mm (W)×110 mm (D)×49 mm (H)
Weight 792 g
Chassis Material Metal
Silkscreen Color Black
Operating Temperature 0 ˚C~40 ˚C/32 ˚F~104 ˚F
Storage Temperature −20 ˚C~60 ˚C/−4 ˚F~140 ˚F
Relative Humidity 20~90% RH (No Condensation)
Power Consumption 3 W
9. ACRONYMS
ACRONYM COMPLETE TERM
CEC Consumer Electronics Control
HDMI High-Denition Multimedia Interface
MHL Mobile High-Denition Link

www.geratech.com.tr
www.egerate.com
www.egerate-store.com