geratech EGE-UHD-1042FS User manual

EGE-UHD-1042FS
10x2 HDMI 4K UHD Matrix Fast Switching

EGE-UHD-1042FS
10x2 HDMI 4K UHD Matrix Fast Switching
3
DISCLAIMERS
The information in this manual has been carefully checked and is believed to be accurate.
Geratech assumes no responsibility for any infringements of patents or other rights of third
parties which may result from its use.
Geratech assumes no responsibility for any inaccuracies that may be contained in
this document. Geratech also makes no commitment to update or to keep current the
information contained in this document.
Geratech reserves the right to make improvements to this document and/or product at any
time and without notice.
COPYRIGHT NOTICE
No part of this document may be reproduced, transmitted, transcribed, stored in a retrieval
system, or any of its part translated into any language or computer le, in any form or by
any means - electronic, mechanical, magnetic, optical, chemical, manual, or otherwise -
without express written permission and consent from Geratech.
© Copyright 2014 by Geratech.
All Rights Reserved.
Version 1.0 November 2014
TRADEMARK ACKNOWLEDGMENTS
All products or service names mentioned in this document may be trademarks of the
companies with which they are associated.

EGE-UHD-1042FS
10x2 HDMI 4K UHD Matrix Fast Switching
4
SAFETY PRECAUTIONS
Please read all instructions before attempting to unpack or install or operate this
equipment, and before connecting the power supply.
Please keep the following in mind as you unpack and install this equipment:
• Always follow basic safety precautions to reduce the risk of re, electrical shock and
injury to persons.
• To prevent re or shock hazard, do not expose the unit to rain, moisture or install this
product near water.
• Never spill liquid of any kind on or into this product.
• Never push an object of any kind into this product through module openings or empty
slots, as you may damage parts.
• Do not attach the power supply cabling to building surfaces.
• Do not allow anything to rest on the power cabling or allow it to be abused by persons
walking on it.
• To protect the equipment from overheating, do not block the slots and openings in the
module housing that provide ventilation.
REVISION HISTORY
VERSION NO. DATE DD/MM/YY SUMMARY OF CHANGE
VR0 22/06/15 Preliminary Release

EGE-UHD-1042FS
10x2 HDMI 4K UHD Matrix Fast Switching
5
CONTENTS
1. Introduction.....................................................................................1
2. Applications ....................................................................................1
3. Package Contents ..........................................................................1
4. System Requirements....................................................................1
5. Features...........................................................................................2
6. Operation Controls and Functions ...............................................3
6.1 Front Panel..................................................................................3
6.2 Rear Panel...................................................................................5
6.3 Remote Control ...........................................................................6
6.4 OSD Menu...................................................................................8
6.5 RS-232 Protocols ......................................................................12
6.6 IR Pin Denitions.......................................................................12
6.7 IP Searching Software Application and Installation ...................13
6.8 Telnet & RS-232 Commands.....................................................14
6.9 Telnet Control ............................................................................16
6.10 WebGUI Control ......................................................................18
7. Connection Diagram ....................................................................20
8. Specications ..............................................................................21

EGE-UHD-1042FS
10x2 HDMI 4K UHD Matrix Fast Switching
1
1. INTRODUCTION
This 10 by 2 HDMI UHD Matrix is an advanced solution for switching up to 10 HDMI
inputs to two HDMI outputs. It provides high performance pass-through of video/audio
and is capable of receiving and transmitting 300MHz/9Gbps bandwidth rate with no data
loss. It’s Fast Switching technology can greatly reduce the time required to swap between
inputs. Supporting the latest features you can be assured of reliable and high quality HDMI
distribution.
2. APPLICATIONS
• Showroom display & control
• Educational demo
• Installation usage
• Advertising display
3. PACKAGE CONTENTS
• 10 By 2 HDMI Matrix Fast Switch
• 1 x IR Extender
• 1 x Remote Control with Battery
• 1 x 5V/2.6A Power Adaptor
• 1 x Left & Right Ear Racks
• Operational Manual
4. SYSTEM REQUIREMENTS
Input source equipment such as DVD/Blu-ray player and output HD display/Monitor with
HDMI cables.

EGE-UHD-1042FS
10x2 HDMI 4K UHD Matrix Fast Switching
2
5. FEATURES
• Supports UHD resolutions up to 4K2K@24/25/30Hz & 4K2K YUV420@60Hz
• Supports HDTV resolutions up to 1080@60Hz, ‘Deep Color’ 36/30/24-bit and PC
resolutions up to WUXGA@60Hz(RB)
• Supports 3D
• Supports pass-through of audio formats: LPCM 2/5.1/7.1CH, Dolby Digital 2~5.1CH,
DTS 2~5.1CH, Dolby Digital Plus, Dolby TrueHD, Dolby Atmos and DTS-HD Master
Audio
• Supports EDID selection function
• Supports control via IR, RS-232, Telnet and WebGUI controls
• Input port HDCP support Standard and Apple mode. The Apple mode selection to
guarantees the use of Apple devices.
• Compliant with DVI source
Note: Supporting HDMI to DVI conversion when HDMI sources is non- deep color and
color space RGB.

EGE-UHD-1042FS
10x2 HDMI 4K UHD Matrix Fast Switching
3
6. OPERATION CONTROLS AND FUNCTIONS
6.1 Front Panel
POWER
10X2 HDMI MATRIX FAST SWITCH
IN 6 IN 7IN 8IN 9IN 10 OUT BTAKE
IN 1IN 2IN 3IN 4IN 5OUT ACANCEL
ENTER
MENU
PRESET
ALL
MUTE
LOCK
+
-
7
6
9
8
11
12
13
14
10 1554321
1POWER Button
Press this button to switch On or set the device to standby mode.
2POWER LED
This LED will illuminate in green when the device is power On and if it is switched to
standby mode the LED will turn red.
3IR Window
This IR Receiver receives the remote control signal from the package included remote
control only.
4IN 1~10
Press these IN buttons to select an input from the 10 input sources.
5OUT A/B
Press these buttons once a time along with an IN buttons to select an input source for
an output display. i.e. OUTA →IN1 →TAKE or OUTB →IN10 →TAKE.
6CANCLE
Press this button to cancel the IN/OUT selection and during any selection under MENU.
7TAKE
Press this button to conrm the selection of an IN and an OUT button. If this button is
not pressed the IN & OUT selection will not be executed.
8MENU
Press to enter into the menu selection.
9ENTER
Press to conrm the selection.
10 +/-
Press these buttons to move up/down under menu selection.
11 PRESET
Press this button to recall the preset setting from 1~10. Press and select from IN1~10
then press TAKE to conrm the recall selection or press CANCEL to exit the selection.
To reset the Preset setting, enter into menu and select Preset setting from IN1~10 then

EGE-UHD-1042FS
10x2 HDMI 4K UHD Matrix Fast Switching
4
press OUTA and select an input from IN1~10 then press OUTB and select an input
from IN1~10 again and press ENTER to conrm the selection. eg. To preset 2’s gure,
MENU → ENTER → Matrix Preset →Enter→Preset2 →IN2 →OUTA →IN8 →OUTB →
IN7 →ENTER
12 ALL
Press this button to select all outputs to display with an input source. e.g. To select all
output with input source 3. ALL →IN3
13 MUTE
Press this button to mute video and audio on OUT A or B or on all output. e.g. To mute
output A OUTA →MUTE
14 LOCK
Press this button to lock all button functions on the panel to unlock, press the button and
hold for 3 seconds.
15 LCM
Displaying Input and Outputs selection and menu selection.

EGE-UHD-1042FS
10x2 HDMI 4K UHD Matrix Fast Switching
5
6.2 Rear Panel
CONTROLSERV.
HDMI IN HDMI OUT
12345678910A BRS232 IR IN DC 5V
7654321
1HDMI IN
Connect from source equipment such as Blu-ray/DVD/PS3 players, Set-Top-Box or any
HDMI equipped source device for input signal sending.
2HDMI OUT
Connect to HDMI TV/display or HD Amplier for output image and or audio display.
3SERV.
This slot is reserved for rmware update use only.
4CONTROL
Connect from PC/Laptop with active internet service for Telnet or WebGUI control with
RJ-45 terminated cable.
5RS-232
Connect from PC/Laptop for RS-232 command sending to control the device.
6IR IN
Connect the IR Receiver included in the package for IR signal receive from the included
remote control.
7DC 5V
Connect the adaptor included in the package and connect to AC wall outlet for power
supply.

EGE-UHD-1042FS
10x2 HDMI 4K UHD Matrix Fast Switching
6
6.3 Remote Control
1POWER
Press this button to switch On or set the device to standby
mode.
2MUTE
Press this button to mute video and audio on OUT A or B or
on all output. e.g. To mute output A OUTA →MUTE
3OUT A/B
Press these buttons once a time along with an IN buttons to
select an input source for an output display. i.e. OUTA →IN1
→TAKE or OUTB →IN10 →TAKE.
4IN 1~10
Press these IN buttons to select an input from the 10 input
sources.
5+/-
Press these buttons to move up/down under menu selection.
6OK
Press to conrm the selection.
7CANCEL
Press this button to cancel the IN/OUT selection and during any selection under MENU.
8MENU
Press to enter into the menu selection.
9TAKE
Press this button to conrm the selection of an IN and an OUT button. If this button is
not pressed the IN & OUT selection will not be executed.
OK
+
-
A
OUT
B1
IN
POWER MUTE
CANCEL MENU
TAKE PRESET
LOCK ALL
CR-151
234
567
8910
1
3
5
7
9
11
2
4
8
12
6
10

EGE-UHD-1042FS
10x2 HDMI 4K UHD Matrix Fast Switching
7
10 PRESET
Press this button to recall the preset setting from 1~10. Press and select from IN1~10
then press TAKE to conrm the recall selection or press CANCEL to exit the selection.
To reset the Preset setting, enter into menu and select Preset setting from IN1~10 then
press OUTA and select an input from IN1~10 then press OUTB and select an input from
IN1~10 again and press ENTER to conrm the selection. eg. To preset 2’s gure, MENU
→ENTER →Matrix Preset →ENTER →Preset2 →IN2 →OUTA →IN8 →OUTB →IN7 →
ENTER
11 LOCK
Press this button to lock all button functions on the panel to unlock, press the button and
hold for 3 seconds.
12 ALL
Press this button to select all outputs to display with an input source. e.g. To select all
output with input source 3. ALL →IN3

EGE-UHD-1042FS
10x2 HDMI 4K UHD Matrix Fast Switching
8
6.4 OSD Menu
Main Menu Sub Menu Description Default
EDID Mode All All Input port is using
same EDID.
In menu “EDID All”, can
select suitable EDID.
All
Appoint Each Input port can
select individual EDID.
In menu “EDID IN1~10”
select suitable EDID.
Exit
EDID All Sink A Copy Output A
display EDID
8/2D/
PCM/1080p
Sink B Copy Output B
display EDID
8/2D/
PCM/720p
Standard EDID, Content:
deep color/2D3D/audio/
native resolution
8/2D/PCM/
AC3/720p
Standard EDID, Content:
deep color/2D3D/audio/
native resolution
8/2D/
PCM/1080p
Standard EDID, Content:
deep color/2D3D/audio/
native resolution
8/2D/PCM/
AC3/1080p
Standard EDID, Content:
deep color/2D3D/audio/
native resolution
8/2D/
PCM/4K2K
Standard EDID, Content:
deep color/2D3D/audio/
native resolution
8/2D/PCM/
AC3/4K2K
Standard EDID, Content:
deep color/2D3D/audio/
native resolution
8/2D/PCM/
Y420
Standard EDID, Content:
deep color/2D3D/audio/
native resolution
8/2D/PCM/
AC3/Y420
Standard EDID, Content:
deep color/2D3D/audio/
native resolution
Exit
EDID IN1 Same EDID All Select Input 1’s EDID Same EDID All
EDID IN2 Same EDID All Select Input 2’s EDID Same EDID All
EDID IN3 Same EDID All Select Input 3’s EDID Same EDID All
EDID IN4 Same EDID All Select Input 4’s EDID Same EDID All

EGE-UHD-1042FS
10x2 HDMI 4K UHD Matrix Fast Switching
9
Main Menu Sub Menu Description Default
EDID IN5 Same EDID All Select Input 5’s EDID Same EDID All
EDID IN6 Same EDID All Select Input 6’s EDID Same EDID All
EDID IN7 Same EDID All Select Input 7’s EDID Same EDID All
EDID IN8 Same EDID All Select Input 8’s EDID Same EDID All
EDID IN9 Same EDID All Select Input 9’s EDID Same EDID All
EDID IN10 Same EDID All Select Input 10’s EDID Same EDID All
Matrix
Preset
Preset 1 IN/OUT default No.1 A=1 , B=1
Preset 2 No.2 A=1 , B=1
Preset 3 No.3 A=1 , B=1
Preset 4 No.4 A=1 , B=1
Preset 5 No.5 A=1 , B=1
Preset 6 N0.6 A=1 , B=1
Preset 7 N0.7 A=1 , B=1
Preset 8 N0.8 A=1 , B=1
Preset 9 N0.9 A=1 , B=1
Preset 10 N0.10 A=1 , B=1
Exit
To reset the Preset setting, select a Preset from 1~10 then press
OUTA and select an input from 1~10 then press OUTB and select an
input from 1~10 again and press ENTER to conrm the selection.
HDCP Input IN1 Standard/
Apple
Set IN1 in Apple/
Standard mode
Standard
IN2 Standard
/Apple
Set IN2 in Apple/
Standard mode
Standard
IN3 Standard
/Apple
Set IN3 in Apple/
Standard mode
Standard
IN4 Standard
/Apple
Set IN4 in Apple/
Standard mode
Standard
IN5 Standard
/Apple
Set IN5 in Apple/
Standard mode
Standard
IN6 Standard
/Apple
Set IN6 in Apple/
Standard mode
Standard
IN7 Standard
/Apple
Set IN7 in Apple/
Standard mode
Standard
IN8 Standard
/Apple
Set IN8 in Apple/
Standard mode
Standard
IN9 Standard
/Apple
Set IN9 in Apple/
Standard mode
Standard

EGE-UHD-1042FS
10x2 HDMI 4K UHD Matrix Fast Switching
10
Main Menu Sub Menu Description Default
IN10 Standard
/Apple
Set IN10 in Apple/
Standard mode
Standard
Exit
Network
Setup
IP Mode DHCP , Static DHCP
IP Setup Static IP 192.168.1.50
Mask Setup Static Netmask 255.255.255.0
Gate Setup Static Gateway 192.168.5.254
Do Re-Link Re-Link.
After setup Network,
the system need to re-
link
---
Exit
Network
Status
Link Network status
DHCP,Static or Not
Linked
---
IP Get IP ---
Mask Get Netmask ---
Gate Get Gateway ---
MAC System MAC Address ---
Exit
Source
Detection
(Detect
Source’s
5V-pin only)
IN1 On/Off ,
IN2 On/Off
IN1 , IN2 detect source
with/without the signal
---
IN3 On/Off ,
IN4 On/Off
IN3 , IN4 detect source
with/without the signal
IN5 On/Off ,
IN6 On/Off
IN5 , IN6 detect source
with/without the signal
IN7 On/Off ,
IN8 On/Off
IN7 , IN8 detect source
with/without the signal
IN9 On/Off ,
IN10 On/Off
IN9 , IN10 detect source
with/without the signal
Exit
Sink A Info Type, Manuf. Detect and Analysis
Output A display’s EDID
Content: type(HDMI/
DVI/VGA), Manufactory/
Model number
---

EGE-UHD-1042FS
10x2 HDMI 4K UHD Matrix Fast Switching
11
Main Menu Sub Menu Description Default
Native Content: native
resolution
Video Format Content: deep color,
2D or 3D, 4K2K
Audio Format Content: PCM,
BitStream, HBR
Exit
Sink B Info Same Sink A
Info
Detect and Analysis
Output B display’s EDID
---
Firmware FW Version Display the model
number and FW version
---
Update FW Update
Exit
Factory
Reset
Do Reset Do system Reset ---
Exit
Exit

EGE-UHD-1042FS
10x2 HDMI 4K UHD Matrix Fast Switching
12
6.5 RS-232 Protocols
Switch Remote Control
PIN Assignment PIN Assignment
1 NC 1 NC
2 TxD 2 RxD
3 RxD 3 TxD
4 NC 4 NC
5 GND 5 GND
6 NC 6 NC
7 NC 7 NC
8 NC 8 NC
9 NC 9 NC
Baud Rate: 115200bps
Data bit: 8 bits
Parity: None
Flow Control: None
Stop Bit: 1
6.6 IR Pin Denitions
IR Signal
Power
Grounding
IR Receiver
3
1
2

EGE-UHD-1042FS
10x2 HDMI 4K UHD Matrix Fast Switching
13
6.7 IP Searching Software Application and Installation
Please download the software from www.geratech.com with le name CDPS V2.000 and
save it in a directory where you may use it later.
Connect the Control System with PC/Laptop through the Ethernet port through an active
network system and open the CDPS V2.000 application. Click on Find Devices on Network
and a list of the devices connected to the Control System will show up.
Then user may use the IP Address to nd the control device through Telnet, WebGUI or
even RS-232/Hyper Terminal tools.

EGE-UHD-1042FS
10x2 HDMI 4K UHD Matrix Fast Switching
14
6.8 Telnet & RS-232 Commands
Command Name Description Description of
parameter
P0 Power Off (Standby) NONE
P1 Power On NONE
A NSet Output A Source N=1-10
B NSet Output B Source N=1-10
I NSet All Outputs Source N=1-10
IPCONFIG Display The Current IP
Congure
NONE
SIPADDR XXX.XXX.
XXX.XXX
Set Ethernet IP
Address
XXX=0~255
SNETMASK XXX.XXX.
XXX.XXX
Set Ethernet Net Mask XXX=0~255
SGATEWAY XXX.XXX.
XXX.XXX
Set Ethernet Gateway XXX=0~255
HTTPPORT NSet Http Port Number N=0~65535
RSTIP IP Conguration Reset
To <DHCP>
NONE
EDIDMODE Show EDID MODE NONE
EDIDMODE NSet EDID Mode N=0(Appoint), 1(All)
EDIDALL Show EDID Mode
Source For All
NONE
EDIDALL NSet EDID Mode Source
For All
N=1-10
EDIDIN Show Input EDID
Source
NONE
EDIDIN N1 Show Input N1 EDID
Source
N1=1-10
EDIDIN N1 N2 Set Input N1 EDID
Source
N1=1-10 N2=1-10
HDCPIN Input HDCP Status NONE
HDCPIN N1 Show Input N1 HDCP
Status
N1=1-10
HDCPIN N1 N2 Set Input N1 HDCP
On/Off
N1=1-10 N2=0(OFF),
1(ON)
PRESET Show All Preset
Congure
NONE
PRESET N1 Set Preset N1 Source
to Outputs
N1=1-10
PRESET N1 N2 Set Preset N1
Congure
N1=1-10 N2=AXBX
(X=01-10,0M)

EGE-UHD-1042FS
10x2 HDMI 4K UHD Matrix Fast Switching
15
Command Name Description Description of
parameter
SOURCEDET Show All Input Signal NONE
SOURCEDET N1 Show Input N1 Signal N1=1-10
SINKINFO Show Output
Information
NONE
INNAME Show Input Name NONE
INNAME N1 N2 Set Input N1 Name N1=1-10
N2=ABCDEFGH(Max
Length=8)
OUTNAME Show Output Name NONE
OUTNAME N1 N2 Set Output N1 Name N1=1-2
N2=ABCDEFGH(Max
Length=8)
VER Show Unit Firmware
Version
NONE
REBOOT System Reboot NONE
HELP (?) Show Command List NONE
HELP NShow Descript Of
Command
N : COMMAND NAME
FADEFAULT All Congure Set To
Factory Default
NONE
Note: All the RS-232 command will be not executed unless followed
with a carriage return. All commands are case-sensitive.