GERLINK UTAMA MANDIRI Gerlip HFNC 01 Product guide

1
Introduction
GLP HFNC 01 is the first High Flow Nasal Cannula
product produced by children of the nation in Indonesia.
This product is the result of research collaboration by
the LIPI Research Institute and PT. Gerlink Utama
Mandiri. This product is one product that needed by
COVID-19 patients during this pandemic. GERLIP
HFNC 01 has been throughthe mechanism of functional
testing and reliability testing by BPFK (Health Facilities
Safety Agency) Jakarta Ministry of Health Republic of
Indonesia. Hope this product able to cure COVID-19
patients whether they are ODP, PDP, or COVID-19
positive. Besides, this product can also used by
pediatrics, children, and adults with various sizes of
Nasal Cannula.
Specification
•High Flow Rate 30-60 LPM.
•Low Flow Rate 5-25 LPM.
•21%-60% and 60%-100% FiO2.
•Heater Humidifier 23°-39° C.
•Relative Humidity ≤80%.
•Standard Breathing Circuit.
•Standard Humidifier.
•Bacteria Filter.
•2 hours Flow Control battery.
•Alarm system (Power, Low Flow, High Flow, and Humidity).

2
Components
Flow Control
(HFNC 01C01)
Main Unit
Humidified Heater
(HFNC 01C02)
Main Unit
Nasal Cannula
(HFNC 01C03)
Disposable Product
Humidified Chamber
(HFNC 01C04)
Disposable Product
Breathing Circuit
(HFNC 01C05)
Disposable Product
Bacteria Filter
(HFNC 01C06)
Disposable Product
Oxygen Tank Regulator
(HFNC 01C07)
Connector & Regulator
Oxygen Hose
(HFNC 01C08)
Connector & Regulator
Connector Medical Hose
(JIS/CIG and Omega)
(HFNC 01C09)
Connector & Regulator
Sensor Wire
(HFNC 01C10)
Cable
AC Power Cable
(HFNC 01C11)
Cable
Heater Wire
(HFNC 01C13)
Cable

3
Tiang Penyangga
(HFNC 01C14)
Support
Main Component Features
1.1.Flow Control

4
1. O2 fraction adjuster.
2. Power button.
3. FiO2selector.
4. Air/compressor inlet.
5. O2alarm adjuster.
6. O2inlet.
7. O2flow adjuster.
8. O2regulator adjuster.
9. O2indicator lamp.
10. Over flow indicator lamp.
11. Power indicator lamp.
12. Respiratory inlet.
13. O2flow monitor.
14. Logo image.
15. Battery indicator.
16. FiO2monitor.
17. O2alarm monitor.
18. Respiratory outlet.
19. Air regulator adjuster.
20. Power cable slot.

5
1.2.Heater Humidifier
1. Temperature value display (in Celcius).
2. Power indicator lamp
3. Heating mode indicator lamp
4. Warning indicator lamp
5. Power, heating mode, and silent alarm button
6. Alarm indicator lamp
7. Heating mode indicator lamp
8. Heater wire
9. Temperature probe
10. Holder
11. Power wire

6
Work Flow
1. O2source and compressed air get in to theregulator box, both adjusted
with pressure to 2 bars, it same with 2 kg/cm2
2. After O2set by regulator at first branch to nozzle through ball valve and
needle valve, another one get in 3 way valve
3. Compressed air after set by regulator get in to 3 way valve
4. 3 way valve functioned for supplying fraction that coose compressed
air, O2, or stop
5. Fraction or flow passing the needle valve to regulating air flow-in to
ventury system

7
6. If that air flow through nozzle and entering the ventury hole, then the air
at around the nozzle will suctioned. If the needle valve fraction closed,
then air from the outside will sunctioned thruogh check valve
7. If needle valve opened, then supply from 3 ways valve will enter with 2
bars pressure. Therefore, check valve will closed and air from the
outside couldn’t entering it. So, if 2 ways valve we choose O2, then the
fraction can reach 100%. If we choose compressed air, then fraction
can reach 21% according to the setting of both needle valve
8. During the operation, both ball valve must be opened

8
Installation Guide
1. Install lower supporting pillar to the wheels.
2. Tighten the lower section of pilar with 8mm L key.
3. Loose the knob, then pull the pillar until stuck, then tighten again.

9
4. Loose the holder of Humidifier slot with 10 mm key, then install it to the
pillar.