German pool GIC-BS26B User manual

BUILT-IN INDUCTION COOKER
嵌入式電磁爐
GIC-BS26B

mm 052
依據參考開孔尺寸[264mm (W) X 379mm (D)]，
在廚櫃檯面開孔。
According to cutout dimensions [264mm (W) X 379mm (D)],
make a cutout hole on the cabinet/counter top.
將隨機的耐油橡膠貼於玻璃支架底部的黏
貼處，然後將機身嵌入櫃中。
Attach the supplied rubber tape to the bottom
part of the unit body, and then place unit
through the cutout hole.
插上電源，安裝完畢。
Connect power and cooker is ready to use.
①
②
③
Notes: When the induction cooker is installed,
the exhaust outlet must be put ONTO the kitchen
work-top, so that it can exhaust successfully.
Please refer to the above pictures.

“ / ”
TIMER / CANCEL
“+ / - ”
“+ / - ” (Adjustment)
“”
POWER ON/OFF
“ / ”
Lock / Unlock
Timer Power Level Setting
“”
“HOT” Indicator
“”
“POWER ON” Indicator
Control Panel
Main Body
Structure Diagram For Reference Only
P.4

“ ”
“ ”
“ ” “ ” Adjustment Keys
“” “LOCK/UNLOCK” Key
Under “Heating” mode, press to set power level.
Under “Sleeping” mode, press to enter “Heating mode”.
Under “Timer Mode” (i.e. when “Timer” Indicator lights up), press to adjust timer.
Press this key to lock all settings at “Heating” mode or “Timer” mode. Under “Lock” status, induction cooker would not
respond to any key press. Press this key for 3 seconds to unlock “LockHol” status.
“ ” “ ” “ ” “ ”
“ ” “POWER ON / OFF” Key
“ ” “TIMER / CANCEL” Key
Turn on the Main ON/OFF Switch or under“Sleeping” mode), press to enter “Heating” mode ( power inicator will be on ).
Press again to switch off operation and return to “Sleeping”.
Note: if no cookware or cookware is not appropriate, the digital display will show “E0” and start to flash.
Press this key to set timer. When the digits “30” are flashing, press “ ” or “ ” key to adjust timer settings between 1 minu-
tes to 6 hours ( the timer indicator will display “01-99” when the timer setup is from 1 to 99 minutes and the timer indicator
will display “2h-6h” when the timer setup is from 2 to 6 hours). Timer will start counting down when time display stops flash-
ing. To cancel timer, press this key again.
Control Button Functions
P.5
注意：當鍋具不適用或沒有放置好時，數碼管會顯示“E0”且閃動以作警示，但電磁爐並不會進行加熱。
打開總電源開關後或與休眠狀態下，按此鍵以進入待機狀態（電源指示燈會亮起）；再按此鍵一次可
轉回休眠狀態。
校定時設定(1分鐘至6小時:1至99分鐘時定時顯示器顯示“01-99”，2至6小時時定時顯示器顯示“
2h-6h"），完成後，定時顯示器會停止閃爍而轉為常亮。再按此鍵可取消定時設定。
於“待機狀態”下，按此兩鍵可使電磁爐進入加熱狀態。
操作說明 OPERATING INSTRUCTIONS

“ ”
“ ”
Connect power plug, and then turn on the Main ON/OFF switch. A “beep" sound is heard, ind-
icating that cooker is in “Sleeping” mode.
“ ”
Place cookware in the centre of cooking hob. Press “POWER” key and power indicator will
light up, then press or indicating that cooker is in “Heating” mode.
(Default value: Level 3)
Press or to adjust power level.
Note: if there is no cookware or cookware not appropriate, cooker will not start operation
and a buzzing sound is heard.
“ ” “ ” “ ”
In “Heating” mode, press “TIMER/CANCEL” key to enter “Timer” mode. Press or to
set shutdown time ranging from 1 minutes to 6 hours ( the timer indicator will display “01-99”
when the timer setup is from 1 to 99 minutes and the timer indicator will display “2h-6h” when
the timer setup is from 2 to 6 hours).
Power Level
Power 300W
2
800W
3
1300W1200W1100W
4
1400W 1500W 1600W
5 6 7 8 9
1700W
MAX
10( )
MIN
1( )
2400W
P.6
操作說明 OPERATING INSTRUCTIONS
休眠
再按
或 鍵，電磁爐便進入加熱狀態（預設火力：第3段）。
定1分鐘至6小時關機時間(1至99分鐘時定時顯示器顯示“01-99”，2至6小時時
定時顯示器顯示“2h-6h"）。
Note: if no cookware or cookware is not appropriate, the digital display will show “E0” and start to flash.
注意：當鍋具不適用或沒有放置好時，數碼管會顯示“E0”且閃動以作警示，但電磁爐並不會進行加熱。

P.7
據⌆ COOKWARE
⊲ᗐᏸ⇞󰩴⚮ 󱁻⚻󰪖ᏸᙬⅅᎵጴ┽ᗤᅗ󱁵Ḫ
ጰᢢ␋ᏸᗥ᎘᎚ᴝ᝸ᅗ᎔ᓑᙨᨬᗽ⇝❀ᅙ
懸䚷䠓▓槭據⌆
Įġġᕛ⋊ġĻġ
ġ ✷ᅘ❻✷ᙬ⍈󱁻ጰ䞌␗
ĮġġᔲᛧġĻġ
ġ ᙑᱡᛸ᥍IJijġŤŮ᎔ጆጴᏗᙑ┽ᅙ┽ᗤᙑᱡᛸġ
ġ ᥍ጰᘹḐ῜ijĶġŤŮᅗ┽ᗤᎧጆᣋᛦᛵᢽḪጰġ
ġ ᘹḐ῜ķġŬŨ
ᾜ懸䚷䠓▓槭據⌆
Įġᕛ⋊ġĻġ
ġ ᜾✷⋊ᜲ✊ᅘᱳᯄᅘᠶ≃፛᎔⋵ᅘⅱᠥᙑᛵġ
ġ┽ᗤ
ĮġᔲᛧġĻġ
ġ ᙑᱡᎣᎥ᥅ḓ῜ጙᛵᅗᙑᱡᛸ᥍ጟᚑĹġŤŮ
󱁻ᙨጰ䞌␗Ჽġġġġġġ✷ℽἂ┽ġġġġġġġġ󱁻ᙨጰ䞌␗┽ġġġġ✷ℽᬕᒩ┽ġġġġ󱁻ᙨ✷ℽᵳ἗Ჽġġġġ✷ᚬİ❻┽
⋵ℽᎁᲽġġġġġġġġġᡴ∻ᠶ≃┽ġġġġġġġġġᱳᯄ┽ġġġġġġġġġġġġᙑᱡᎣᎥጰᏗġġġġġġġ┽ᙑ᜹ὰġġġġġ┽ᙑᛸ᥍῜ጟ
Please use only German Pool authorized cookware
or cookware recommended by us. Any unauthorized
cookware may affect induction cooker’s heating
capacity and quality.
Appropriate Cookware
- Material:
Metal, ferromagnetic stainless steel or cast iron
- Shape:
Flat bottom with a diameter of 12 cm or more.
Cookware bottom diameter should not exceed 25 cm
and must not weight over 6 kg (with food)
Inappropriate Cookware
- Material:
Non-metallic, non-ferromagnetic, ceramic, glass,
aluminum or brass
- Shape:
Bottom not flat or too bumpy, or bottom diameter
smaller than 8 cm
Ferromagnetic
Stainless Steel
Water Pot
Metal Frying Pan Ferromagnetic
Stainless Steel
Cooking Pot
Metal Saucepan Ferromagnetic
Metal Water Pot
Cast Iron Grilling
Pan
Aluminum
Water Pot
Glass Pot Ceramic Pot Pot With Non-Flat/
Curved Bottom
Pot With
Bumpers
Pot Bottom
Too Small

P.8
— Power plug must be disconnected before cleaning.
— Any stain or deposit on the cook-top surface must
be cleaned off immediately before re-using.
— Cleaning must be done when cook-top surface has
completely cooled down.
— If stain is minimal, wipe off with a dry cloth. If stain
remains, clean cook-top with a moist sponge (soaked
with mild soap) and then wipe again with a clean cloth.
— To clean the body of induction cooker, wipe with a
soft clean cloth. If stain remains, clean with a moist
sponge (soaked with mild soap) and then wipe with
a clean cloth.
— Do not immerse induction cooker into water.
— Do not clean cook-top with any rough cloth or
abrasive tool.
— Do not use organic solvents or any cleaning
products that contain chemicals such as Benzene.
Note : Over time, cook-top panel may be
discoloured due to one of the following
situations. Operation of induction cooker
would not be affected as this is normal.
Overheating or burning empty cookware
Spillage not cleaned immediately
Cookware not clean
Long period of usage
CARE & MAINTENANCE
Single 13 A power jack must be used. Do not share
Warning: Switch off the induction cooker in case of any crack on the cook-top panel.
power jack with other appliances.
Do not apply water directly onto induction cooker.
Do not insert any wire or metal objects through air
inlet or venting outlet of the induction cooker.
Please avoid collision between cook-top panel and cookware.
A distance of at least 10 cm between the wall and
the sides of induction cooker must be reserved for
venting purposes.
Do not place or use induction cooker near any
heat source.
Do not heat up any metal plate or other magnetic
objects on the cook-top.
Do not heat empty cookware for an extended time.
Overheating of cookware will cause damages
and injuries.
Do not heat up unopened cans on the cook-top. It
may cause explosion.
Unplug the power cord when induction cooker is not
in use.
SAFETY CAUTIONS
警告：如果微晶玻璃面板有裂紋，關掉器具以避免可能出現的電擊。

P.9
TROUBLESHOOTING
When you run into any problem operating this product, use the table below to troubleshoot the problem.
If the problem persists, contact our Repairs & Customer Service Centre.
“ ”
Power is connected and Main
On/Off switch is turned on, but the
induction cooker does not respond
when the On/Off button is pressed.
Is there a power
shortage in your area?
Is there a short circuit in the
power source of your home?
Is the power plug too loose
or not connected well?
Try again after power supply resumes.
Find out the cause of short circuit
and eliminate it before switching on
the cooker again.
Re-connect the plug or replace the
power jack.
Buzzer beeps continuously and pan
is not heated.
Is the pan not suitable for
induction cooking?
Is the pan positioned properly?
Use an appropriate pan.
Position the pan in the centre of
cook-top.
Induction cooker stops heating
during normal operations.
Is the pan empty or cooking
temperature too high?
Are the air inlet and outlet
being blocked?
Is the surrounding temperature
too high?
Avoid operating cooker with an
empty pan. Let cooker cool down
before switching it on again.
Remove obstruction from the vent.
Let induction cooker cool down and
try again.
Try again after the room cools down.
Temperature fluctuates. Is pan bottom not flat? Replace pan with a flat-bottomed one.
* Above table enlists the most common problems regarding the operations of the product and their possible causes as well as suggested solutions.
It is strictly for users’ reference only.
* Should there be any product malfunction or breakdown, DO NOT repair it yourself. Contact our Repairs & Customer Service Centre or consult a
licensed technician immediately.

P.10
常見故障及處理
TROUBLESHOOTING
故障代碼 故障說明 故障代碼 故障說明
EC 爐面感應器沒安裝到位或脫落
EA
E6 爐面感應器短路
Short circuit of cook-top sensorLoosening of cook-top sensor
E3* 電壓過高
Voltage over-loaded
E7 爐面溫度過高
Cook-top overheat
E4* 電壓過低
Voltage under-loaded
E8 機內溫度感應器短路
Short circuit of internal temperature sensor
E5 爐面感應器斷路
Open circuit of cook-top sensor
E9
E0
機內溫度感應器斷路
鍋具不適用或沒有放置好
Open circuit of internal temperature sensor
No cookware or appropriate cookware
機內溫度過高
Internal overheat
技術規格 TECHNICAL SPECIFICATIONS
*E3 & E4 are not product errors. Operation can be resumed when power voltage returns to normal rating (187V - 253V).
(187 - 253V)
(W)264mm (D) 379 mm
(H) 60 mm (W) 290 mm (D) 405 mm
Approx. 5.2 kg
Approx. 6.3 kg
300 W - 2600 W
Specifications are subject to change without prior notice.
the Chinese version shall prevail.
If there is any inconsistency or ambiguity between the English version and the Chinese version of these operating instructions,
220 - 240 V~ / 50 - 60 Hz
GIC-BS26B
2600 W
2600 W
Model
Rated Power Output
Maximum Out of Cooking Hob
Number of Cooking Hob
Cutout Dimensions
Dimensions
Net Weight
Gross Weight
Power Adjustment Range
Manufacturing Standards
1
GB4706.1-2005, GB4706.22-2008
Voltage / Frequency

保用條款
此保用提供德國寶產品之機件在正常使用下壹
年保用(自購買日起計算)，但不包括安裝、維
修、保養及更換零件之人工或其他費用。
- 此保用不包括﹕因意外而造成的損壞(包括運
輸及其它)﹔任何附件及輔助裝置﹔以及一切因
人為、電源接合不當、不依說明書而錯誤或疏
忽使用本機、經非本公司認可之安裝及不適當
維修等等所引致之損壞。
- 保用只在香港、九龍、新界區有效，東涌、
愉景灣及離島，需額外收取交通費用。
- 未能出示購買發票者，將不獲免費維修服務。
型號 Model No. :
機身號碼 Serial No. :
購買商號 Purchased From :
* 貴戶須在購機十天內¸以下列其中一種方
式向本公司登記資料¸保用手續方正式生效﹕
1)填妥本公司網頁內之保用登記表格
www.germanpool.com/warranty
2)填妥保用登記卡¸並連同購機發票之副本
一併郵寄到客戶服務部
(本公司將不發還發票副本或登記卡)
Warranty Terms & Conditions
Our Repairs & Customer Service Centre will provide
rectification of any defect of manufacturing materials
free of charge given that such defect is reported within
12 months from date of sale.
- Customer should always follow the operating
instructions. This warranty does not apply to: damages
caused by incorrect voltage, improper operations,
unauthorized installation or repairs as well as accidents.
- Service area includes Hong Kong Island, Kowloon and
New Territories. Repairs in Tung Chung, Discovery Bay
or other areas are subject to extra service charge.
- Customer who fails to present original purchase
invoice will be disqualified for free repair services.
* This warranty is not valid until Customer’s
registration information is returned to and
received by our Service Centre within 10 days
of purchase via one of the following methods:
1) Visit our website and register online:
www.germanpool.com/warranty
2) Complete all fields on the attached Warranty
Card and mail it back to our Customer Service
Centre along with a photocopy of the
purchase invoice (Warranty Card and invoice
copy will not be returned to Customer)
客戶服務部
Customer Service Centre
請填妥以下空格並與發票一併保存¸以便維修時核對資料。用戶提供本公司之所有資料必須正確無誤¸否則免費保用將會無效。
發票號碼 Invoice No. :
購買日期 Purchase Date :
Please fill out the form below. This information and the purchase invoice will be required for any repairs. Warranty will be invalid
if information provided is found to be inaccurate.
GIC-BS26B
[phone]
德國寶(香港)有限公司
香港九龍土瓜灣馬頭角道116號
新寶工商中心高層地下2－4室
電話：
German Pool (Hong Kong) Limited
Room 2-4, Upper G/F, Newport Centre,
116 Ma Tau Kok Road,
Tokwawan, Kowloon, Hong Kong
[phone]
傳真：
[email protected]
電郵：
Tel : [phone]
Fax : [phone]
Email : [email protected]
此保用只適用於香港 This warranty is valid only in Hong Kong

www.germanpool.com
( Te l ) ( F a x ) (E-mail)
German Pool (Hong Kong) Limited
R o o m 2 — 4 , U p p e r G r o u n d F l o o r, N e w p o r t C e n t r e
116 Ma Tau Kok Road, Tokwawan, Kowloon, Hong Kong
©
©All rights reserved. Copying, reproducing or using the contents of this publication is not allowed without prior authorization from German Pool, violators will be prosecuted.
2007
GIC-BS26B-M-09-(1)