Ghost Controls ZOMBIELOCK AXZL User manual

WHAT IS INCLUDED IN AXZL KIT:
MOUNTING THE LOCK AND RECEIVER:
NOTE: If your gate is set up in the push-to-open mode, the lock will need to be installed on the outside of the gate.
STEP 1: MAKE SURE THE OPERATOR CONTROL BOX POWER SWITCH IS IN THE OFF POSITION
You must disconnect the operator only after the operator power switch is OFF and the gate is NOT moving.
NOTE: The gate operator is battery powered and unplugging the AC transformer does not turn the power to the operator o.
STEP 2: DISCONNECT FRONT END OF THE GATE OPERATOR ARM FROM GATE BRACKET
A. Remove the hairpin clip and clevis pin from the FRONT mount of the gate operator.
B. Swing the operator arm out of the way of the gate.
STEP 3: MAKE SURE GATE IS IN THE CLOSED POSITION
To ensure the gate remains in the closed position, you should wire tie or clamp the gate to the post for a single gate and for
a dual gate secure the second gate.
Lock should be mounted on the gate cross member or other solid part of the gate surface and the receiver should be
mounted on the adjacent post perfectly level with the lock. See illustrations next page.
RECEIVER
AND PIN NUTS AND
BOLTS
YOU WILL NOT NEED
THE WASHERS FOR
THIS APPLICATION
LOCK
KEYS
AXZL ZOMBIELOCK®AUTOMATIC GATE LOCK
INSTRUCTIONS
OPTIONAL:
TUBE GATE ACCESSORY KIT
(AXTB)

NOTE FOR TUBE GATES
USING TUBE GATE BRACKET KIT: USE THE SUPPLIED LOCKNUTS AND DISCARD THE WASHERS!
THE LOCKNUTS MUST BE SCREWED DOWN ON TUBE BRACKET AND THEN SCREWED ONTO THE
ZOMBIELOCK, AS SHOWN BELOW.
Thread locknuts completely onto Tube Gate Bracket studs. Now thread studs into the Zombielock. Assemble onto gate.
REMOVE AND DISPOSE OF WASHERS INCLUDED IN TUBE BRACKET KIT!
LOCK
KEYS
Mounting on
SINGLE
decorative gates
RECEIVER
AND PIN
MOUNTING
RECEIVER
OPTION 1
Mounting on
SINGLE
tube gates
LOCK
OPTIONAL AXTB
TUBE BRACKETS
KEYS
RECEIVER
AND PIN MAKE SURE LEVEL
AND ALIGNED
MOUNTING
RECEIVER
OPTION 2
Mounting on
SINGLE
tube gates
LOCK
OPTIONAL AXTB
TUBE BRACKETS
KEYS
RECEIVER
AND PIN
MAKE SURE LEVEL
AND ALIGNED
MAKE SURE LEVEL
AND ALIGNED

STEP 4: VERIFY THE RECEIVER PIN LINES UP WITH SLOT IN THE LOCK
The gate lock needs to be level with the receiver.
STEP 5: DRILL HOLES ON THE POST AND ATTACH RECEIVER WITH INCLUDED NUTS AND BOLTS
See illustrations in STEP 3.
STEP 6: GATE LOCK CAN NOW BE PERMANENTLY MOUNTED WITH THE INCLUDED NUTS AND BOLTS TO
THE GATE CROSSMEMBER OR GATE SURFACE.
Drill the holes through the gate to attach bolts, nuts, and washers. Tighten lock securely.
View looking down showing receiver pin lines up with gate lock
RECEIVER
AND PIN
LOCK
LOCK
LOCK
KEYS
KEYS
Mounting on
DUAL
tube gates
Mounting on
DUAL
decorative gates
OPTIONAL AXTB
TUBE BRACKETS
INSTALL LOCK ON GATE
CLOSEST TO CONTROL PANEL
GATE CLOSEST TO
CONTROL PANEL
RECEIVER
AND PIN
RECEIVER
AND PIN
MAKE SURE LEVEL
AND ALIGNED
MAKE SURE LEVEL
AND ALIGNED

AXZLIM | REV 0118
©2018 GHOST CONTROLS®
CONNECTING LOCK TO THE CONTROL BOX
STEP 1: VERIFY SWITCH AT CONTROL BOX IS OFF
STEP 2: RUN THE ZOMBIELOCK WIRES FROM GATE LOCK TO THE CONTROL BOX
Run the wire across the cross section of the bar into the control box.
STEP 3: CONNECT THE WIRES FROM GATE LOCK TO CONTROL BOX
Connect the gate lock wires to the LOCK
terminals on the control board. Once the
red, black, and blue wires are connected
to the terminals, tighten each of the
screws so that the wires do not come loose.
■Red wire connects to positive (+)
■Black wire connects to negative (–)
■Blue wire connects to S (S)
STEP 4: CONTROLLER WILL
AUTOMATICALLY DETECT THE LOCK
WHEN SWITCH IS TURNED ON
■Lock (if present) will be pulled (unlocked) for a
few seconds at the closed position before open-
ing. If lock is not completely pulled the gate will
not open to prevent damage to the gate and lock.
■Lock will also be pulled (unlocked) near the closed
limit position when it is closing to ensure a smooth
and “soft” closing operation.
STEP 5: RECONNECT OPERATOR ARM TO FRONT GATE BRACKET WITH CLEVIS PIN AND CLEVIS HAIRPIN
NOTE
MAKE SURE THE GATE LOCK CLOSES FIRMLY IN THE RECEIVER, SOME ADJUSTMENTS OF GATE
CLOSURE MAY BE NECESSARY. REFER TO YOUR GATE OPENER MANUAL FOR THE CLOSED POSITION
ADJUSTMENT.
BLUE
BLACK
RED
GATE LOCK WIRE
WARNING: This product can expose you to chemicals including
lead, which is known to the State of California to cause cancer.
For more information, go to www.P65Warnings.ca.gov.