GIGA-TMS AUR720-BXX User manual

1
AUR720-BXX
User’s Manual
Published: 2021/2/2
Version 1.0.3
This document describes the AUR720-BXX product and relevant software
operation supplied by GIGA-TMS INC. To check for more recent editions of
this document, see http://ftp.gigatms.com.tw/disks/DISK5479/
GIGA-TMS INC.

2
Warning
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one of the following
measures:
. Reorient or relocate the receiving antenna.
. Increase the separation between the equipment and receiver.
. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
. Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: To assure continued compliance, any changes or modifications not expressly approved by the
party responsible for compliance could void the user's authority to operate this equipment. (Example - use
only shielded interface cables when connecting to computer or peripheral devices).
FCC SAR evaluation
This equipment complies with SAR test exclusion thresholds.
Contains transmitter module: FCC ID: SH6MDBT40

3
DEMOSTRATION SOFTWARE LICENSE
Please read this agreement carefully before you start to install this demonstration software. If you do not
agree please stop the installation of the software.
Software developed by GITA-TMS INC is provided “AS IS” without warranty of any kind, either express or
implied, including, but not limited to, the implied warranties of fitness for a purpose, or the warranty of
non-infringement. Without limiting the forgoing GIGA-TMS INC makes no warranty that:
⚫The software will meet you requirements.
⚫The software will be uninterrupted, timely, secure or error-free.
⚫The results that may be obtained from the use of the software will be effective, accurate or reliable.
⚫The quality of the software will meet your expectations.
⚫Any errors in the software obtained from GIGA-TMS INC will be corrected.
The software and its documentation made available for test or demo purpose
⚫could include technical or other errors, GIGA-TMS INC may make changes to the software or
documentation made available to shipped with the conjunction products
⚫may be out of date, and GIGA-TMS INC makes no responsibility to update such materials
In no event shall GIGA-TMS INC be liable to you or any third party for any special incidental, indirect or
consequential damages of any kind, or any damages whatsoever, including, without limitation, those
resulting from loss of use, data or profits, whether or not GIGA-TMS INC has been advised of the possibility
of damage, and on any theory of liability, arising out of or in connection with the use of the software.
The installation of the software is done at your own consideration and risk and with agreement that you
will be solely responsibility for any damage to your system or loss of data that results from such activities.

4
LIMITED WARRANTY
GIGA-TMS warrants that the products sold pursuant to this Agreement will perform in accordance with GIGA-TMS’s published
specifications. This warranty shall be provided only for a period of one year from the date of the shipment of the product from
GIGA-TMS (the “Warranty Period”). This warranty shall apply only to the “Buyer” (the original purchaser, unless that entity
resells the product as authorized by GIGA-TMS, in which event this warranty shall apply only to the first re-purchaser).
During the Warranty Period, should this product fail to conform to GIGA-TMS’s specifications, GIGA-TMS will, at its option, repair
or replace this product at no additional charge except as set forth below. Repair parts and replacement products will be
furnished on an exchange basis and will be either reconditioned or new. All replaced parts and products become the property of
GIGA-TMS. This limited warranty does not include service to repair damage to the product resulting from accident, disaster,
unreasonable use, misuse, abuse, negligence, or modification of the product not authorized by GIGA-TMS. GIGA-TMS reserves
the right to examine the alleged defective goods to determine whether the warranty is applicable.
Without limiting the generality of the foregoing, GIGA-TMS specifically disclaims any liability or warranty for goods resold in
other than GIGA-TMS’s original packages, and for goods modified, altered, or treated without authorization by GIGA-TMS.
Service may be obtained by delivering the product during the warranty period to GIGA-TMS (8F No. 31 Lane 169, Kang Ning
Street, Hsi Chih Dist New Taipei City, Taiwan). If this product is delivered by mail or by an equivalent shipping carrier, the
customer agrees to insure the product or assume the risk of loss or damage in transit, to prepay shipping charges to the
warranty service location, and to use the original shipping container or equivalent. GIGA-TMS will return the product, prepaid,
via a three (3) day shipping service. A Return Material Authorization (“RMA”) number must accompany all returns. Buyers may
obtain an RMA number by contacting Technical Support at [phone].
EACH BUYER UNDERSTANDS THAT THIS GIGA-TMS PRODUCT IS OFFERED AS IS. GIGA-TMS MAKES NO OTHER
WARRANTY, EXPRESS OR IMPLIED, AND GIGA-TMS DISCLAIMS ANY WARRANTY OF ANY OTHER KIND, INCLUDING
ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
IF THIS PRODUCT DOES NOT CONFORM TO GIGA-TMS’S SPECIFICATIONS, THE SOLE REMEDY SHALL BE REPAIR OR REPLACEMENT
AS PROVIDED ABOVE. GIGA-TMS’S LIABILITY, IF ANY, SHALL IN NO EVENT EXCEED THE TOTAL AMOUNT PAID TO GIGA-TMS
UNDER THIS AGREEMENT. IN NO EVENT WILL GIGA-TMS BE LIABLE TO THE BUYER FOR ANY DAMAGES, INCLUDING ANY LOST
PROFITS, LOST SAVINGS, OR OTHER INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OF, OR INABILITY TO
USE, SUCH PRODUCT, EVEN IF GIGA-TMS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES, OR FOR ANY CLAIM BY
ANY OTHER PARTY.
LIMITATION ON LIABILITY
EXCEPT AS PROVIDED IN THE SECTIONS RELATING TO GIGA-TMS’S LIMITED WARRANTY, GIGA-TMS’S LIABILITY UNDER THIS
AGREEMENT IS LIMITED TO THE CONTRACT PRICE OF THIS PRODUCT.
GIGA-TMS MAKES NO OTHER WARRANTIES WITH RESPECT TO THE PRODUCT, EXPRESSED OR IMPLIED, EXCEPT AS MAY BE
STATED IN THIS AGREEMENT, AND GIGA-TMS DISCLAIMS ANY IMPLIED WARRANTY, INCLUDING WITHOUT LIMITATION ANY
IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
GIGA-TMS SHALL NOT BE LIABLE FOR CONTINGENT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES TO PERSONS OR PROPERTY.
GIGA-TMS FURTHER LIMITS ITS LIABILITY OF ANY KIND WITH RESPECT TO THE PRODUCT, INCLUDING ANY NEGLIGENCE ON ITS
PART, TO THE CONTRACT PRICE FOR THE GOODS.
GIGA-TMS’S SOLE LIABILITY AND BUYER’S EXCLUSIVE REMEDIES ARE STATED IN THIS SECTION AND IN THE SECTION RELATING TO
GIGA-TMS’S LIMITED WARRANTY.

5
Terminology
AUR720
The handheld UHF reader.
EAN
One of GS1 Barcodes, contains EAN-8 and EAN-13 which supports GTIN-8 and
GTIN-13 separately.
EPC
Electronic product code
EPC PC
The PC field I EPC memory bank.
EPC ID
The EPC field in EPC memory bank
GS1
Global Standard One. GS1 is a not-for-profit organization that develops and
maintains global standards for business communication.
GS1 Barcodes
The barcodes that are issued and managed by GS1.
GTIN
Global Trade Item Number (GTIN) can be used by a company to uniquely identify
all of its trade items. GS1 defines trade items as products or service
PC
Protocol control
RF
Radio frequency
RFID
Radio-frequency identification
SGTIN
The EPC schema to encode a GTIN is the SGTIN which consists of the GTIN plus a
unique product or serial number.
TID
Tag-identification or Tag identifier, depending on context
UHF
Ultra High Frequency
UPC
One of GS1 Barcodes, contains UPC-E and UPC-A which supports GTIN-8 and
GTIN-12 separately.

6
Contents
TERMINOLOGY ........................................................................................................................................................................... 5
CONTENTS.................................................................................................................................................................................. 6
INTRODUCTION .......................................................................................................................................................................... 9
GETTING STARTED .................................................................................................................................................................... 10
INSTALL USB DRIVER USING THE AUR720B UTILITY FOR WINDOWS .......................................................................................................... 11
INSTALL AUR720B UTILITY FOR WINDOWS ........................................................................................................................................... 11
OPEN AUR720B UTILITY FOR WINDOWS.............................................................................................................................................. 11
SET UP AUR720 READER CLOCK ......................................................................................................................................................... 11
CONFIGURE AUR720 READER SETTINGS............................................................................................................................................... 12
READ BARCODE AND WRITE TO EPC..................................................................................................................................................... 13
DOWNLOAD LOG DATA....................................................................................................................................................................... 14
HARDWARE FEATURES.............................................................................................................................................................. 15
CABLES AND CONTROLS...................................................................................................................................................................... 15
Operation Status LED............................................................................................................................................................... 16
Bluetooth Status LED ............................................................................................................................................................... 16
OLED Display............................................................................................................................................................................ 17
Back Button ............................................................................................................................................................................. 17
Power/Next Button .................................................................................................................................................................. 17
Action Button........................................................................................................................................................................... 17
USB Connector......................................................................................................................................................................... 17
Antenna ................................................................................................................................................................................... 17
Buzzer ...................................................................................................................................................................................... 17
Battery..................................................................................................................................................................................... 18
Barcode Scanner...................................................................................................................................................................... 18
Reset Hole................................................................................................................................................................................ 18
PART NUMBERS................................................................................................................................................................................ 19
SPECIFICATIONS................................................................................................................................................................................. 20
DEVICE OPERATIONS ................................................................................................................................................................ 21
TURNING ON AUR720 ...................................................................................................................................................................... 21
TURNING ON BLUETOOTH ................................................................................................................................................................... 21
PAIRING AS A BLUETOOTH KEYBOARD.................................................................................................................................................... 22
Pair in Windows....................................................................................................................................................................... 22
Pair in Android ......................................................................................................................................................................... 22
Pair in iOS ................................................................................................................................................................................ 23
Make a Test.............................................................................................................................................................................. 23
HOLDING AUR720 FOR READING RFID TAG ......................................................................................................................................... 24

7
DESKTOP MODE FOR READING RFID TAG.............................................................................................................................................. 25
BARCODE SCANNER OPERATION........................................................................................................................................................... 26
READING BARCODE TECHNIQUES.......................................................................................................................................................... 27
CHARGE AND MONITOR THE BATTERY ................................................................................................................................................... 28
EXTEND BATTERY LIFE ........................................................................................................................................................................ 29
SELECTING MENU ............................................................................................................................................................................. 30
Main Menu Diagram ............................................................................................................................................................... 31
Copy and Paste (Barcode to EPC) Diagram.............................................................................................................................. 32
Copy and Paste (Barcode to User Memory) Diagram .............................................................................................................. 33
Copy and Paste (EPC to EPC) Diagram..................................................................................................................................... 34
Read EPC Diagram................................................................................................................................................................... 35
Read User Memory Diagram ................................................................................................................................................... 36
Read Barcode Diagram............................................................................................................................................................ 37
Device Information Diagram ................................................................................................................................................... 38
MENU OPERATION ............................................................................................................................................................................ 39
Copy and Paste (Barcode to EPC) Menu .................................................................................................................................. 40
Copy and Paste (Barcode to User Memory) Menu .................................................................................................................. 41
Copy and Paste (EPC to EPC) Menu ......................................................................................................................................... 42
Read EPC Menu ....................................................................................................................................................................... 43
Read User Memory Menu........................................................................................................................................................ 44
Read Barcode Menu ................................................................................................................................................................ 45
Device Information Menu........................................................................................................................................................ 46
LOG DATA........................................................................................................................................................................................ 48
CHOOSE EPC ENCODER AND DECODER ................................................................................................................................................. 48
SOFTWARE MANUALS .............................................................................................................................................................. 49
AUR720 USB DRIVER FOR WINDOWS ................................................................................................................................................. 50
Overview.................................................................................................................................................................................. 50
Install the USB Driver............................................................................................................................................................... 50
FIRMWARE LOADER FOR WINDOWS...................................................................................................................................................... 51
Install the Program.................................................................................................................................................................. 51
Open the Program ................................................................................................................................................................... 51
Explore the User Interface ....................................................................................................................................................... 52
Using Firmware Loader ........................................................................................................................................................... 53
AUR720B UTILITY PROGRAM FOR WINDOWS ....................................................................................................................................... 55
Install the Program.................................................................................................................................................................. 55
Open the Program ................................................................................................................................................................... 55
Explore the User Interface ....................................................................................................................................................... 56
Using AUR720B Utility ............................................................................................................................................................. 60
AUR720B UTILITY APP FOR IOS AND ANDROID ..................................................................................................................................... 77
Installing the App..................................................................................................................................................................... 77
Open the App........................................................................................................................................................................... 77
Using AUR720B Utility App...................................................................................................................................................... 78

8
AUR720B SDK LIBRARY FOR WINDOWS ............................................................................................................................................ 105
AUR720B SDK LIBRARY FOR ANDROID .............................................................................................................................................. 105
AUR720B SDK LIBRARY FOR IOS...................................................................................................................................................... 105
FREQUENTLY ASKED QUESTIONS............................................................................................................................................ 106
APPLICATION NOTES............................................................................................................................................................... 108
UHF GEN2 MEMORY ...................................................................................................................................................................... 108
Reserved Memory.................................................................................................................................................................. 108
EPC Memory .......................................................................................................................................................................... 109
TID Memory........................................................................................................................................................................... 109
User Memory......................................................................................................................................................................... 110
TECHNICAL SUPPORT.............................................................................................................................................................. 111
UPDATE HISTORY.................................................................................................................................................................... 112

9
Introduction
The AUR720 is a handheld UHF RFID reader, which is compliant with UHF EPC Class1/Class3 Gen2/ISO
18000-6C standards.
The AUR720 is designed for short reading range applications. It features BLE communication interface,
which be able to send out the reading data to BLE-enabled host, such as computer, smartphone or tablet.
The reader is integrated with 2D barcode scanner, which make it able to do copy-paste function (read
barcode then write to tag EPC memory) under offline operation.
Set up the BLE to Bluetooth HID profile to support keyboard emulation, which can direct send tag, barcode
data to host application without requiring any SDK Library implemented.
The AUR720 supports for Windows 7, 10, Android, iPhone and iPad.

10
Getting Started
This getting started topic shows you the following operations for the first time to use the AUR720 reader:
Install USB Driver using the AUR720B Utility for Windows
Install AUR720B Utility for Windows
Start AUR720B Utility for Windows
Set up AUR720 Clock
Configure AUR720 Settings
Read Barcode and Write to RFID-Tag
Download Log Data

11
Install USB Driver using the AUR720B Utility
for Windows
1. Use web browser to open the link
http://ftp.gigatms.com.tw/public/disks/disk5479/index_AUR720B.html
2. Download the USB driver zip file.
3. For Windows 8/8.1/10, open the Win8 folder and click dpinst_x86.exe (for 32-bit system) or
dpinst_amd64.exe (for 64-bit system) file to install the driver.
- or -
For Windows XP/7, open the Win7 folder and click dpinst_x86.exe (for 32-bit system) or
dpinst_amd64.exe (for 64-bit system) file to install the driver.
Install AUR720B Utility for Windows
1. Use web browser to open the link
http://ftp.gigatms.com.tw/public/disks/disk5479/index_AUR720B.html
2. Download the AUR720B Utility setup file for Windows.
3. Double click setup file to install program to your computer.
Open AUR720B Utility for Windows
1. On the taskbar, click Start, and then point to All Programs.
2. Point to GIGA-TMS, point to AUR720, and then click AUR720B Utility.
Set up AUR720 Reader Clock
1. Start AUR720B Utility.
2. Connect AUR720 to USB port of computer by using USB cable.
3. AUR720B Utility detects the port where AUR720 connects and then automatically updates the reader
clock with using computer time.
You can view AUR720 clock by 1) scrolling AUR720 main menu to Device Information. 2) Press Action

12
button to view the clock.
Configure AUR720 Reader Settings
Following procedure shows an example to turn off the buzzer by using AUR720B Utility.
1. Connect AUR720 to computer by using USB cable.
2. Open AUR720B Utility program.
3. Click to select the Buzzer to Disabled, and then click Update Settings to Device.

13
Read Barcode and Write to EPC
Following procedure shows the method of using AUR720 to scan a barcode and copy the data to the RFID-
Tag EPC memory.
1. Turn on your AUR720 by pressing the Power/Next button and hold until the starting up message
appears.
2. Press Power/Next button or Back button to scroll the menu to Copy/Paste Barcode to EPC, press
Action Button to scan the barcode image.
AUR720 detects the barcode and show the data on the screen.
3. Press Action Button and approach AUR720 to the tag. Once reader detects the tag, it will write
barcode data to the tag EPC memory.
4. Press Back button to return to main menu, or press Action Button to write the same barcode data to
the other tag.
Write EPC
succeeded
Select Tag...
[Main Menu]
Copy/Paste
Barcode to EPC
Barcode:
72527273076

14
Download Log Data
This topic shows you using the AUR720B Utility for Windows to download the log data. The log is the data
that AUR720 reads from the barcode and RFID-tag.
Following procedure shows the method of downloading the save log data to computer.
1. Connect AUR720 to computer by using USB cable.
2. On the Device menu, click Download Log to start the process of downloading the log data.
3. After completing the log download, it will automatically open the log file by Notepad program.
Note:
It needs to turn on the Save Barcode/EPC Data setting to let AUR720 automatically save the reading
barcode and tag EPC data to its internal memory.

15
Hardware Features
Cables and Controls
Back button
Power/Next button
Action button
OLED display
Bluetooth status LED
Operation status LED
USB Connector

16
Operation Status LED
The Operation Status LED can light 2 colors – green and red, which is used to indicate following status:
Green light Indicate:
▪The operation result is successful.
Red light Indicate:
▪The operation result is failed.
- or -
▪The battery is on charging. If the battery is fully charged, then the red light will turn off.
Bluetooth Status LED
The Bluetooth status LED is use to indicate the communication status via Bluetooth:
Blue light Paired with host.
Flashing Blue light Indicates Bluetooth is on but not paired yet (stays in discover mode).
Buzzer
Antenna
Battery
Barcode Scanner
Reset Hole

17
Off Bluetooth is off.
OLED Display
The screen size is 128 x 64, which can show 16 x 4 characters in text mode. The fore color of font is yellow.
Back Button
The Back button is used to
Scroll the menu to previous one. You can use this button to select menu or return to main menu.
Turn on Bluetooth by pressing and holding for 2 seconds. Once the Bluetooth turns on, the Bluetooth
Status LED will keep flashing for 60 seconds.
Power/Next Button
The Power/Next button is used to
Scroll the menu to next one. You can use this button to select menu.
Turn sleep to wake mode by pressing and holding for 2 seconds.
Action Button
The Action button is used to execute the function of selected menu.
USB Connector
The USB interface type of AUR720 is USB Type-C, which is compatible with USB1.1 to 2.0. The USB
connector provides the functions of
Connecting to the computer USB port for communicating with host program.
Connecting to battery charger for charging.
Antenna
Antenna is a conductor that can transmit, send and receive UHF radio signals. Approach this area to tag to
get better reading performance. The reading distance is up to 10 cm.
Buzzer
The buzzer is used to make beep sound to notify the user the operation result. One beep indicates the
operation is successful, Three short beeps indicates the operation has failed.

18
Battery
The device uses an 800 mA Lithium Polymer Rechargeable battery, which can power the device for
approximately 10 hours using one RF scan per 10 seconds ( approx. 3600 scans)
Barcode Scanner
The 2D barcode scanner can scan 1D and 2D barcode image.
Reset Hole
Used for reset AUR720 device.

19
Part Numbers
Device numbering scheme is as follows:
Part Number
Description
AUR720-B00
The frequency range of antenna is designed for following regions:
Japan, US, China 920.625, Korea, Taiwan, Brazil, Uruguay, Israel
AUR720-B30
The frequency range of antenna is designed for following regions:
Europe, China 840.125
AUR720-B
“00” or “30”

20
Specifications
Features
UHF reader read range
10 cm
Memory size
64K bytes
Status Indicator
2 RGB LEDs
Display
16 x 4 OLED (text mode)
Buzzer
1
Vibration
1
Button
3
Power/Next button x 1
Back button x 1
Action button x 1
Barcode Scanner
2D
Log Count
Maximum: 4680
Communication
Bluetooth
V4.0, Bluetooth Classic and Low Energy (BLE)
USB
HID profile
Electrical
RFID interface
UHF EPC Class1/Class3 Gen2/ISO 18000-6C compatible
Battery type
Lithium Polymer Rechargeable battery , 800mA, 3.7V
Battery life
Wake mode:
6.5 hours with RF and barcode scanning per 10 seconds
(about 1700 scans).
16 hours with RF scanning per 10 seconds (about 4800
scans).
Sleep mode: 16 days
Battery charging time
3~4 hours
Environment
Operating Temperature
Charge: 0℃~ 45℃
Discharge: -20℃~ 60℃
Storage Temperature
-20℃ ~ 45℃
Humidity
65±20% RH
Dimensions
Width
63 mm
Height
118 mm
Depth
23 mm
Weight
130 g