Gigabyte GZ-XX1CA-SNS User manual

Triton Series
English User’s Manual
Triton + Triton 180
Triton GZ-XX1CA-SNS/SNB
Triton 180 GZ-AX1CA-SDS/SDB GZ-AX1CA-SD1/SD2

English
2
Thank you for purchasing GIGABYTE thermal product. GIGABY TE
is dedicated to the integration of casing liquid/air-cooling solution
technology, to provide users with the most optimal solution for heat
dissipation. For further information and specifications of the “Triton”
series, please visit GIGABYTE website. (http://www.gigabyte.com.tw)
The Following are not covered by the warranty:
1. Using the product incorrectly or in a manner other than the designed purpose.
2. Nonobservance of the proper operations provided.
3. Malfunction due to interference from other devices.
4. Unapproved modification of the product.
5. Consequential damage to other objects due to the product’s fault.
6. Malfunction arising from natural hazards E.g. earthquake, lighting, fire and floods.
7. The product’s warranty label has been removed or damaged.
8. The devices inside, including power supply, hard disk, CD-ROM drive, motherboard,
ventilator, etc, are not detached from the casing prior to transportation of the computer
system, resulting in damage to the casing or other computer-related devices.
9. Any loss/damage caused by failure to follow the installation process with in the user
manual.
Triton 180
Triton
Failure to wear gloves during installation of computer products
may cause bodily harm or damage to your devices. Incorrect
connector installation may possibly burn out the motherboard
and other components. Be sure to observe the instructions in
the user manual.

English
3
Table of Contents
1. Components Introduction 4
1-1 Casing’s Internal Structure 4
1-2 Front and Rear Panel Structure 5
1-3 Removal of Side and Front Panels 6
2. Features 6
3. Specifications 7
4. Installation Instructions 8
4-1 Installation of Power Supply 8
4-2 Installation of Motherboard 8
4-3 Installation of Add-on Card 9
4-4 Installation of Front Multi-Media I/O Port 10
4-5 Installation of Fan Power Cable 11
4-6 Installation of 5.25” Front Device Bay 12
4-7 Installation of 3.5” Front Device Bay 12
4-8 Installation of 3.5” Internal Device Bay 13
4-9 Foot Supports 13
4-10 Liquid Cooling System Support 13
4-11 Recommended Cooling Products 14

English
4
1.Components Introduction
1-1 Casing’s Internal Structure
1
2
3
4
5
6
7
8
Power Supply
1
Motherboard
Tray
2
PCI Tool-Free
Fastener
3
5.25” Front
Device Bay
4
3.5” Front
Device Bay
5
3.5” Internal
Device Bay
6

English
5
1-2 Front and Rear Panel Structure
a) Front Panel b) Rear Panel
Accessory Box
7
Securing Runner
x 6
Copper Stand Off
x 9
Motherboard
Securing Screw x 9
Power Supply
Securing Screw x 4
Wire Clamp x 1 Magnet Ring x 1
Front Cable Kit
8
USB 2.0 Audio Set
(HD & AC’97)
IEEE1394
(Multi-connectors)
3-Pin Fan
Connector
Basic chassis power
switch control cable kit
Triton 180 Triton
a-1) Reset SW / HDD LED / Power SW / Power LED
a-2)Front multi-media I/O ports
(USB x2, IEEE 1394 x1, Audio Set x1 (HD &AC’97))
b-1) Rear Fan
b-2) LCS Tube Inlet/Outlet
b-1
b-2
a-1
a-2

English
6
1-3 Removal of Side and Front Panels
1-3.1 To remove side panels:
Remove the 4 thumb screws at the rear of the
side panels, and detach the side panels.
1-3.2 To remove front panel:
Remove the left and right side panels (see step 1-3.1), release
the 4 clamps the hold the front panel onto the chassis.
2.Features
-High Quality Design
• High-end aluminum bezel design
• Skid-proof & shock-proof foot stands
-Complete Support
• Front panel multi-media I/O ports
(USB x2, IEEE 1394 x1, Audio Set x1 (HD &AC’97))
• Dual 12cm silent & shock proof fan (Front x 1 and Rear x 1)
• Supports liquid cooling systems
-Integration of Cooling Technology
• Intel CAG 1.1 Air Duct
-Convenience of Assembly
• Internal Cable Management
• Tool-free installation design
1-3.1a
1-3.2a

English
7
3.Specifications
Triton Triton 180
Model GZ-XX1CA-SNS/SNB GZ-AX1CA-SDS/SDB
GZ-AX1CA-SD1/SD2
Case Type Middle Tower
Size (W x H x D) 200 x 440x 480 mm
Front Bezel Material Aluminum
Color Silver / Black
Side Panel Intel CAG1.1
Body Material 0.7 mm SECC
Net Weight 8.4kg
5.25” Device Bay (external) 5
3.5” Device Bay (external) 2
3.5” Device Bay (internal) 3
PCI Slot 7
Motherboard Size ATX / Micro ATX / Flex ATX
System Fan (front) 12cm silent fan x 1
System Fan (rear) 12cm silent fan x 1
Multi-Media I/O Port USB2.0 x 2 , IEEE 1394 x 1 ,
Audio Set x 1 (HD & AC'97)

English
8
4.Installation Instructions
Please follow the reference sections in order for installation.
4-1 Installation of Power Supply
To facilitate the installation, it is recommended to set the chassis
upright on the table.
Required Tools: Power supply securing screw x 4.
Remove side panel (see step 1-3.1 on page 6).
Place the power supply unit into the case.
Secure the power supply with the 4 securing
screws.
4-2 Installation of Motherboard
This chassis is compatible with ATX / Micro ATX / Flex ATX
motherboards.
Please confirm the dimensions and fixing points of the
motherboard prior to installation.
Required Tools: Copper stand offs, Motherboard screws.
According to motherboard specifications,
select proper screw points, screw in the
copper stand offs into the corresponding
points on the motherboard.
Change the motherboard I/O bracket on the
rear panel (supplied by the motherboard
manufacturer).
4-1.1
4-1.2
4-2.1
4-2.2

English
9
Secure the motherboard with the motherboard
screws (refer to your motherboard manual to
check what type of motherboard you have).
4-3 Installation of Add-on Card
This chassis supports tool-free installation of add-on cards, e.g.
graphics cards, sound cards, and etc.
Required Tools: None
Unlock the corresponding PCI tool-free
fastener by pushing it downwards.
Lift the fastener upwards and remove the
internally attached dust-proof PCI cover.
Insert the add-on card into the expansion slot
and then lock the PCI tool-free fastener.
4-2.3
Motherboard Code name Motherboard
screws
Case copper
post
ATX A1-A9 9 9
Micro ATX U1-U9 9 9
Flex ATX F1-F6 6 6
4-3.1
4-3.2
4-3.3

English
10
4-4 Installation of Front Multi-Media I/O Ports
The front panel consists of:
(1) 2 x USB, 1 x IEEE 1394 and 1 x Audio Set (HD & AC’97)
(2) Basic casing power switch control cable kit.
Required Tools: None
(1) 2 x USB, 1 x IEEE 1394 and 1 x Audio Set (HD & AC’97)
Insert the USB 2.0 connectors into the
corresponding socket on the motherboard.
Insert the IEEE 1394 connector into the
corresponding socket on the motherboard.
Please refer to the instructions supplied by the motherboard
manufacturer and make sure the correct type of connector is used
prior to installation.
Incorrect connection of the slots can possibly cause the
motherboard to malfunction or completely destroy the
motherboard. Please read the installation procedure within the
user manual as incorrect installations or connections causing
faults will void your warranty.
4-4.1
4-4.2
Pin Definition Pin Definition
1 Power 6 USB Dy+
2 Power 7 GND
3 USB Dx- 8 GND
4 USB Dy- 9
5 USB Dx+ 10 USB Over current
USB 2.0 connector
Pin Definition Pin Definition
1 TPA+ 6 TPB-
2 TPA- 7
3 GND 8 +12V
4 GND 9 +12V
5 TPB+ 10 GND
IEEE 1394 connector A
Pin Definition Pin Definition
1 TPA+ 6 TPB-
2 TPA- 7 +12V
3 GND 8 +12V
4 GND 9
5 TPB+ 10 GND
IEEE 1394 connector B
Pin Definition Pin Definition
1 +12V 9 +12V
2 +12V 10 +12V
3 TPA+ 11 TPA1+
4 TPA- 12 TPA1-
5 GND 13 GND
6 GND 14
7 TPB+ 15 TPB1+
8 TPB- 16 TPB1-
IEEE 1394 connector C
A
B C

English
11
Insert the Audio connector into the corresponding
socket on the motherboard.
(2) Basic casing power switch control cable kit.
Follow the connectors list below for installation
(see figure below)
4-5 Connection of Fan Power Cables
This chassis has one 12cm silent cooling fan in the front and one in
the rear. This case includes internal connectors that connects the
front and rear fans making it into a single 3-pin connector.
Required Tools: None
Plug the 3-pin connector into the
corresponding system fan socket on the
motherboard.
4-4.3
HD AUDIO Pin Definition Pin Definition
1 MIC2_L 6 FSENSE1
2 GND 7 FAUDIO_JD
3 MIC2_R 8
4 -ACZ_DET 9 LINE2_L
5 LINE2_R 10 FSENSE2
Pin Definition Pin Definition
1 MIC 6 NC
2 GND 7 NC
3 MIC Power 8
4 NC 9 Line Out(L)
5 Line Out(R) 10 NC
AC'97
Connector Color
Speaker Yellow(+) / Black(-)
Reset SW Blue(+) / White(-)
Power SW Orange(+) / White(-)
Power LED+ Green
Power LED- White
H.D.D. LED Red(+) / White(-)
Different motherboards have different installation areas
and specifications, screw holes and connectors. For detailed
instructions, please refer to the motherboard user manual
supplied by the motherboard manufacturer.
4-5.1

English
12
4-6 Installation of 5.25” Front Device Bay
This chassis can accommodate up to 5 x 5.25” front devices.
Required Tools: None
Detach the front panel (see step 1-3.2 on page 6) and remove
the mesh drive rail from the front panel.
Remove the front EMI plate and attach the
front panel onto the chassis.
Slide the 5.25” device into the drive bay from
the front of the chassis.
Secure the 5.25” device with the internal latch.
Refer to the figure for installation procedure.
4-7 Installation of 3.5” Front Device Bay
This chassis can accommodate up to 2 x 3.5” front devices.
Required Tools: None
Installation of 3.5” front devices is the same as
5.25” front devices, please refer to step 4-6.
4-6.1
4-6.2
4-6.3
4-6.4
4-7.1
Lock

English
13
4-8 Installation of 3.5” Internal Device Bay
This chassis provides internal device bays to accommodate up to
3 hard disc drives. The internal device requires securing runners,
which can be found be found in the accessory box.
Required Tools: Securing runners (2 per hard disc drive)
Fit the securing runners on both sides of the
HDD and slide the HDD into the internal device
bay.
4-9 Foot Supports
This chassis is supplied with four high-end skid-
proof foot supports for ensuring the casing is
firmly seated on the holding surface.
4-10 Liquid Cooling System
This chassis can fully support the GIGABYTE 3D Galaxy liquid
cooling system (it also supports majority of liquid cooling
systems available commercially). While installing the liquid
cooling system, please refer to the manual provided with the
liquid cooling system.
4-8.1
Additional HDD can be installed in the 3.5” front
device bay. Slide in the HDD and lock the internal
latch to secure the HDD.

English
14
4-11 Recommended Cooling Products
This chassis is recommended to be used with GIGABYTE cooling
products.