Gigabyte 7002 Series User manual

R152-Z30
R152-Z31
R152-Z32
AMD®EPYCTM 7002 series Processor Server
Service Guide
Rev. 1.0

Copyright
© 2019 GIGA-BYTE TECHNOLOGY CO., LTD. All rights reserved.
The trademarks mentioned in this manual are legally registered to their respective owners.
Disclaimer
Information in this manual is protected by copyright laws and is the property of GIGABYTE.
Changes to the specications and features in this manual may be made by GIGABYTE without
prior notice. No part of this manual may be reproduced, copied, translated, transmitted, or pub-
lished in any form or by any means without GIGABYTE's prior written permission.
Documentation Classications
In order to assist in the use of this product, GIGABYTE provides the following types of documentations:
For detailed product information, carefully read the User's Manual.
For More Information
For related product specications, the latest rmware and software, and related information, please visit
our website at:
http://www.gigabyte.com
For GIGABYTE distributors and resellers, additional sales & marketing materials are available from our
reseller portal:
http://reseller.b2b.gigabyte.com
For further information & technical assistance, please contact your GIGABYTE sales representative.
You may also message GIGABYTE server directly by email, Facebook or twitter
Email: server[email protected]
Facebook: https://www.facebook.com/gigabyteserver
Twitter: https://twitter.com/GIGABYTEServer

Conventions
The following conventions are used in this user's guide:
NOTE!
Gives bits and pieces of additional
information related to the current topic.
CAUTION!
Gives precautionary measures to
avoid possible hardware or software problems.
WARNING!
Alerts you to any damage that might
result from doing or not doing specic actions.

Server Warnings and Cautions
Before installing a server, be sure that you understand the following warnings and cautions.
WARNING!
To reduce the risk of electric shock or damage to the equipment:
• Do not disable the power cord grounding plug. The grounding plug is an important safety
feature.
• Plug the power cord into a grounded (earthed) electrical outlet that is easily accessible at all
times.
• Unplug the power cord from the power supply to disconnect power to the equipment.
• Do not route the power cord where it can be walked on or pinched by items placed against it.
Pay particular attention to the plug, electrical outlet, and the point where the cord extends from
the server.
WARNING!
To reduce the risk of personal injury from hot surfaces, allow the drives
and the internal system components to cool before touching them.
WARNING!
This server is equipped with high speed fans. Keep away from hazardous
moving fan blades during servicing.
CAUTION!
• Do not operate the server for long periods with the access panel open or removed. Operat-
ing the server in this manner results in improper airow and improper cooling that can lead to
thermal damage.
• Danger of explosion if battery is incorrectly replaced.
• Replace only with the same or equivalent type recommended by the manufacturer.
• Dispose of used batteries according to the manufacturer’s instructions.

Electrostatic Discharge (ESD)
CAUTION!
ESD CAN DAMAGE DRIVES, BOARDS, AND OTHER PARTS. WE RECOMMEND THAT YOU
PERFORM ALL PROCEDURES AT AN ESD WORKSTATION. IF ONE IS NOT AVAILABLE,
PROVIDE SOME ESD PROTECTION BY WEARING AN ANTI-STATIC WRIST STRAP AT-
TACHED TO CHASSIS GROUND -- ANY UNPAINTED METAL SURFACE -- ON YOUR SERVER
WHEN HANDLING PARTS.
Always handle boards carefully. They can be extremely sensitive to ESD. Hold boards only by
their edges without any component and pin touching. After removing a board from its protective
wrapper or from the system, place the board component side up on a grounded, static free sur-
face. Use a conductive foam pad if available but not the board wrapper. Do not slide board over
any surface.
System power on/off: To remove power from system, you must remove the system from
rack. Make sure the system is removed from the rack before opening the chassis, adding, or
removing any non hot-plug components.
Hazardous conditions, devices and cables: Hazardous electrical conditions may be
present on power, telephone, and communication cables. Turn off the system and discon-nect
the cables attached to the system before servicing it. Otherwise, personal injury or equipment
damage can result.
Electrostatic discharge (ESD) and ESD protection: ESD can damage drives,
boards, and other parts. We recommend that you perform all procedures in this chapter only at
an ESD workstation. If one is not available, provide some ESD protection by wearing an antistatic
wrist strap attached to chassis ground (any unpainted metal surface on the server) when handling
parts.
ESD and handling boards: Always handle boards carefully. They can be extremely
sensi-tive to electrostatic discharge (ESD). Hold boards only by their edges. After removing a
board from its protective wrapper or from the system, place the board component side up on a
grounded, static free surface. Use a conductive foam pad if available but not the board wrapper.
Do not slide board over any surface.
Installing or removing jumpers: A jumper is a small plastic encased conductor that slips
over two jumper pins. Some jumpers have a small tab on top that can be gripped with n-gertips
or with a pair of ne needle nosed pliers. If the jumpers do not have such a tab, take care when
using needle nosed pliers to remove or install a jumper; grip the narrow sides of the jumper with
the pliers, never the wide sides. Gripping the wide sides can dam-age the contacts inside the
jumper, causing intermittent problems with the function con-trolled by that jumper. Take care to
grip with, but not squeeze, the pliers or other tool used to remove a jumper, or the pins on the
board may bend or break.

CAUTION!
Risk of explosion if battery is replaced incorrectly or with an incorrect type. Replace the battery
only with the same or equivalent type recommended by the manufacturer. Dispose of used bat-
teries according to the manufacturer’s instructions.

- 7 -
Table of Contents
Chapter 1 Hardware Installation ................................................................................... 11
1-1 Installation Precautions.................................................................................. 11
1-2 Product Specications.................................................................................... 12
1-3 System Block Diagram................................................................................... 15
Chapter 2 System Appearance.....................................................................................17
2-1 Front View...................................................................................................... 17
2-2 Rear View....................................................................................................... 17
2-3 Front Panel LED and Buttons ........................................................................ 18
2-4 Rear System LAN LEDs................................................................................. 20
2-5 Hard Disk Drive LEDs .................................................................................... 21
Chapter 3 System Hardware Installation ......................................................................23
3-1 Removing Chassis Cover............................................................................... 24
3-2 Removing and Installing the Fan Duct ........................................................... 25
3-3 Installing the CPU and Heat Sink................................................................... 26
3-4 Installing the Memory..................................................................................... 28
3-4-1 Eight Channel Memory Conguration.....................................................................28
3-4-2 Installing a Memory ...............................................................................................29
3-4-3 DIMM Population Table ..........................................................................................29
3-5 Installing the PCI Expansion Card ................................................................. 31
3-6 Installing the Hard Disk Drive......................................................................... 33
3-7 Installing the Mezzanine Card (Optional)....................................................... 35
3-8 Replacing the FAN Assemblly ........................................................................ 36
3-9 Replacing the Power Supply.......................................................................... 37
3-10 Installing the Mezzanine Card (Optional)....................................................... 38
3-11 Cable Routing ................................................................................................ 39
3-11-1 R152-Z30 Cable Routing........................................................................................39
3-11-2 R152-Z31 Cable Routing........................................................................................41
3-11-3 R152-Z32 Cable Routing........................................................................................43
Chapter 4 Motherboard Components ...........................................................................47
4-1 Motherboard Components ............................................................................. 47
4-2 Jumper Settings ............................................................................................. 49
Chapter 1 BIOS Setup ..................................................................................................51
5-1 The Main Menu .............................................................................................. 53
5-2 Advanced Menu ............................................................................................. 55

- 8 -
5-2-1 Trusted Computing .................................................................................................56
5-2-2 PSP Firmware Versions..........................................................................................57
5-2-3 Legacy Video Select...............................................................................................58
5-2-4 AST2500 Super IO Conguration...........................................................................59
5-2-5 S5 RTC Wake Settings...........................................................................................62
5-2-6 Serial Port Console Redirection .............................................................................63
5-2-7 CPU Conguration..................................................................................................65
5-2-8 PCI Subsystem.......................................................................................................67
5-2-9 USB Conguration..................................................................................................69
5-2-10 NVMe Conguration ...............................................................................................71
5-2-11 SATA Conguration.................................................................................................72
5-2-12 Network Stack ........................................................................................................73
5-2-13 AMD Mem Conguration Status.............................................................................74
5-2-14 iSCSI Conguration................................................................................................75
5-2-15 Tls Auth Conguration ............................................................................................76
5-2-16 AVAGO MegaRAID Conguration Utility ................................................................77
5-2-17 Intel(R) I350 Gigabit Network Connection..............................................................79
5-2-18 VLAN Conguration................................................................................................81
5-2-19 MAC IPv4 Network Conguration...........................................................................83
5-2-20 MAC IPv6 Network Conguration...........................................................................84
5-3 AMD CBS Menu............................................................................................. 85
5-3-1 Valhalla Common Options ......................................................................................86
5-3-2 DF Common Options..............................................................................................88
5-3-3 UMC Common Options ..........................................................................................89
5-3-4 NBIO Common Options..........................................................................................94
5-3-5 FCH Common Options ...........................................................................................95
5-3-6 NTB Common Options ...........................................................................................96
5-3-7 SOC Miscellaneous Control ...................................................................................97
5-4 AMD PBS Option Menu ................................................................................. 98
5-4-1 RAS ........................................................................................................................99
5-5 Chipset Setup Menu..................................................................................... 101
5-5-1 North Bridge .........................................................................................................102
5-6 Server Management Menu........................................................................... 103
5-6-1 System Event Log ................................................................................................105
5-6-2 View FRU Information ..........................................................................................106
5-6-3 BMC Network Conguration.................................................................................107
5-6-4 IPv6 BMC Network Conguration.........................................................................108
5-7 Security Menu .............................................................................................. 109
5-7-1 Secure Boot..........................................................................................................110
5-8 Boot Menu.................................................................................................... 112
5-9 Save & Exit Menu......................................................................................... 114

- 9 -
5-10 ABL POST Codes ........................................................................................ 115
5-10-1 StartProcessorTestPoints .....................................................................................115
5-10-2 Memory test points ...............................................................................................115
5-10-3 PMU Test Points ...................................................................................................115
5-10-4 Original Post Code ...............................................................................................116
5-10-5 CPU test points.....................................................................................................117
5-10-6 Topology test points..............................................................................................117
5-10-7 Extended memory test point.................................................................................117
5-10-8 Gnb Earlier init......................................................................................................118
5-10-9 PMU test points ....................................................................................................121
5-10-10 ABL0 test points ...................................................................................................121
5-10-11 ABL5 test points ...................................................................................................121
5-11 Agesa POST Codes..................................................................................... 125
5-11-1 Universal Post Code.............................................................................................125
5-11-2 [0xA1XX] For CZ only memory Postcodes...........................................................125
5-11-3 S3 Interface Post Code ........................................................................................128
5-11-4 PMU Post Code....................................................................................................128
5-11-5 [0xA5XX] assigned for AGESA PSP Module........................................................128
5-11-6 [0xA9XX, 0xAAXX] assigned for AGESA NBIO Module.......................................131
5-11-7 [0xACXX] assigned for AGESA CCX Module.......................................................133
5-11-8 [0xADXX] assigned for AGESA DF Module..........................................................134
5-11-9 [0xAFXX] assigned for AGESA FCH Module........................................................134
5-12 BIOS POST Beep code (AMI standard)....................................................... 136
5-12-1 PEI Beep Codes...................................................................................................136
5-12-2 DXE Beep Codes .................................................................................................136
5-13 BIOS Recovery Instruction........................................................................... 137

- 10 -
This page intentionally left blank

- 11 - Hardware Installation
1-1 Installation Precautions
The motherboard/system contain numerous delicate electronic circuits and components which
can become damaged as a result of electrostatic discharge (ESD). Prior to installation, carefully
read the service guide and follow these procedures:
• Prior to installation, do not remove or break motherboard S/N (Serial Number) sticker or
warranty sticker provided by your dealer. These stickers are required for warranty validation.
• Always remove the AC power by unplugging the power cord from the power outlet before
installing or removing the motherboard or other hardware components.
• When connecting hardware components to the internal connectors on the motherboard,
make sure they are connected tightly and securely.
• When handling the motherboard, avoid touching any metal leads or connectors.
• It is best to wear an electrostatic discharge (ESD) wrist strap when handling electronic
components such as a motherboard, CPU or memory. If you do not have an ESD wrist
strap, keep your hands dry and rst touch a metal object to eliminate static electricity.
• Prior to installing the motherboard, please have it on top of an antistatic pad or within an
electrostatic shielding container.
• Before unplugging the power supply cable from the motherboard, make sure the power
supply has been turned off.
• Before turning on the power, make sure the power supply voltage has been set according to
the local voltage standard.
• Before using the product, please verify that all cables and power connectors of your
hardware components are connected.
• To prevent damage to the motherboard, do not allow screws to come in contact with the
motherboard circuit or its components.
• Make sure there are no leftover screws or metal components placed on the motherboard or
within the computer casing.
• Do not place the computer system on an uneven surface .
• Do not place the computer system in a high-temperature environment.
• Turning on the computer power during the installation process can lead to damage to
system components as well as physical harm to the user.
• If you are uncertain about any installation steps or have a problem related to the use of the
product, please consult a certied computer technician.
Chapter 1 Hardware Installation

Hardware Installation - 12 -
1-2 Product Specications
Socket
Socket
CPU AMD EPYC™ 7002 series processor family
Single processor, 7nm, Socket SP3
Up to 64-core, 128 threads
NOTE: If only 1 CPU is installed, some PCIe or memory functions might be
unavailable.
Socket
Socket
Chipset System on Chip
Socket
Socket
Memory 16 x DIMM slots
DDR4 memory supported only
8-channel memory architecture
RDIMM modules up to 64GB supported
LRDIMM modules up to 128GB supported
Memory speed: Up to 3200 MHz w/1DPC, 2933MHz w/2DPC
Socket
Socket
LAN 2 x 1Gb/s LAN ports (Intel® I350)
1 x 10/100/1000 management LAN
Socket
Socket
Expansion Slot 1 x Riser card:
- 1 x CRS101D
* 1 x Full-height half-length slot with PCIe x16 (Gen4 x16 bus) slot
1 x OCP mezzanine slots with PCIe Gen3 x16 bandwidth (Type1, P1, P2, P3,
P4; Type2 P5 with NCSI supported)
2 x M.2 slot:
- M-key
- PCIe Gen3 x4
- Supports NGFF-2242/2260/2280 cards
Socket
Socket
Video Integrated in Aspeed® AST2500
2D Video Graphic Adapter with PCIe bus interface
1920x1200@60Hz 32bpp, DDR4 SDRAM
Socket
Socket
Storage
(R12-Z30)
4 x 3.5" SAS/SATA hot-swappable HDD/SSD bays
SAS card is required for SAS devices support
(R152-Z31) 8 x 2.5" SAS/SATA, 2 x 2.5" U.2 hot-swappable HDD/SSD bays
SAS card is required for SAS devices support
(R152-Z32) 10 x 2.5" U.2 hot-swappable HDD/SSD bays
Socket
Socket
SAS Supported via add-on SAS Card

- 13 - Hardware Installation
Socket
Socket
Front Panel
LED/Buttons
(R152-Z30)
2 x USB 3.0
1 x Power button with LED
1 x ID button with LED
1 x NMI button
1 x Reset button
2 x LAN activity LEDs
1 x HDD activity LED
1 x System status LED
(R152-Z31)
(R152-Z32)
1 x USB 3.0
1 x Power button with LED
1 x ID button with LED
1 x NMI button
1 x Reset button
2 x LAN activity LEDs
1 x HDD activity LED
1 x System status LED
Socket
Socket
Rear Panel I/O 3 x USB 3.0
1 x VGA
2 x RJ45
1 x MLAN
1 x ID button with LED
Socket
Socket
Backplane I/O
(R152-Z30)
SATA(6Gb/s)
(R152-Z31)
(R152-Z32)
SAS(12Gb/s) / SATA(6Gb/s)/ NVMe(8Gb/s)
Socket
Socket
TPM 1 x TPM header with SPI interface
Optional TPM2.0 kit: CTM010
Socket
Socket
System
Management
Aspeed® AST2500 management controller
Avocent® MergePoint IPMI 2.0 web interface:
Network settings
Network security settings
Hardware information
Users control
Services settings
IPMI settings
Sessions control
LDAP settings
Power control
Fan proles
Voltages, fans and temperatures monitoring
System event log
Events management (platform events, trap settings, email settings)
Serial Over LAN
vKVM & vMedia (HTML5)

Hardware Installation - 14 -
Socket
Socket
Power Supply
(R152-Z30)
(R152-Z31)
2 x 650W redundant PSUs
80 PLUS Platinum
AC Input:
- 100-240V/ 12-7A, 50-60Hz
- 200-240V/ 7A, 50-60Hz
DC Output:
- 1200W
- 12V, 80.5A (100-240V)
- 12V, 97A (200-240V)
- 12Vsb, 3A
(R152-Z32) 2 x 850W redundant PSUs
80 PLUS Platinum
AC Input:
- 100-240V/ 12-7A, 50-60Hz
- 200-240V/ 7A, 50-60Hz

DC Output:
- 1200W
- 12V, 80.5A (100-240V)
- 12V, 97A (200-240V)
- 12Vsb, 3A
Socket
Socket
Environment
Ambient
Temperature
Relative
Humidity
Operating temperature: 10°C to 35°C
Non-operating temperature: -40°C to 60°C
Operating humidity: 8-80% (non-condensing)
Non-operating humidity: 20%-95% (non-condensing)
Socket
Socket
System
Dimension
1U
438mm (W) x 43.5mm (H) x 730mm (D)
* We reserves the right to make any changes to the product specications and product-related information without
prior notice.

- 15 - Hardware Installation
1-3 System Block Diagram
R152-Z30
R152-Z31
R152-Z32

Hardware Installation - 16 -
This page intentionally left blank

- 17 - System Appearance
Chapter 2 System Appearance
2-1 Front View
No. Description
1. Front Panel LEDs and buttons
2. Front USB 3.0 Port
Orange HDD Latches Support NVMe
• Please Go to Chapter 2-3 Front Panel LED and Buttons for detail description of function
LEDs.
2-2 Rear View
No. Description
1. Serial Port
2. VGA Port
3. Mezzanine Card Slot (Option/OCP V2.0 Card)
4. 10/100/1000 Server management LAN port
5. ID Button
6. USB 3.0 Port x 2
7. GbE LAN Port x 2
8. USB 3.0 Port
9. PCIe Card Slot
R152-Z30
R152-Z31
R152-Z32
1 2
HDD#0 HDD#1 HDD#2 HDD#3
12
HDD#0
HDD#1
HDD#2
HDD#3
HDD#4
HDD#5
HDD#6
HDD#7
HDD#8
HDD#9
12
HDD#0
HDD#1
HDD#2
HDD#3
HDD#4
HDD#5
HDD#6
HDD#7
HDD#8
HDD#9
21 3 5
46 7 8
9
PSU1PSU2

System Appearance - 18 -
2-3 Front Panel LED and Buttons
No. Name Color Status Description
1. NMI button
Press the button server generates a NMI to the processor
if the multiple-bit ECC errors occur, which effectively halt
the server.
2. Reset Button Press the button to reset the system.
3/4
LAN 1/2
Active/Link
LEDs
Green Solid On Link between system and network or no access.
Green Blink Data trasmission or receiving is occuring
N/A Off No data transmission or receiving is occuring
5. HDD Status
LED
Green On HDD locate
Blink HDD access
Amber On HDD fault
Green/
Amber Blink HDD rebuilding
N/A Off No HDD access or no HDD fault.
6. System
Status LED
Green Solid On System is operating normally.
Amber
Solid On
Critical condition, may indicate:
System fan failure
System temperature
Blink
Non-critical condition, may indicate:
Redundant power module failure
Temperature and voltage issue
Chassis intrusion
N/A Off
System is not ready, may indicate:
POST error
NMI error
Processor or terminator missing
7. ID Button Press the button to activate system identication
8. Power button
with LED
Green On System is powered on
Green Blink System is in ACPI S1 state (sleep mode)
N/A Off
• System is not powered on or in ACPI S5 state
(power off)
• System is in ACPI S4 state (hibernate mode)
R52-Z30
L2 SYS ID
L1
RST
NMI
12 3 4 5 6 7 8

- 19 - System Appearance
No. Name Color Status Description
1. Reset Button Press the button to reset the system.
2. NMI button
Press the button server generates a NMI to the processor
if the multiple-bit ECC errors occur, which effectively halt
the server.
3. Power button
with LED
Green On System is powered on
Green Blink System is in ACPI S1 state (sleep mode)
N/A Off
• System is not powered on or in ACPI S5 state
(power off)
• System is in ACPI S4 state (hibernate mode)
4. ID Button Press the button to activate system identication
5. HDD Status
LED
Green On HDD locate
Blink HDD access
Amber On HDD fault
Green/
Amber Blink HDD rebuilding
N/A Off No HDD access or no HDD fault.
6. System
Status LED
Green Solid On System is operating normally.
Amber
Solid On
Critical condition, may indicate:
System fan failure
System temperature
Blink
Non-critical condition, may indicate:
Redundant power module failure
Temperature and voltage issue
Chassis intrusion
N/A Off
System is not ready, may indicate:
POST error
NMI error
Processor or terminator missing
7/8.
LAN 1/2
Active/Link
LEDs
Green Solid On Link between system and network or no access.
Green Blink Data trasmission or receiving is occuring
N/A Off No data transmission or receiving is occuring
L1 L2
2
4
6
8
1
3
5
7
R152-Z31
R152-Z32

System Appearance - 20 -
2-4 Rear System LAN LEDs
No. Name Color Status Description
1. 1GbE
Speed LED
Yellow On 1 Gbps data rate
Green On 100 Mbps data rate
N/A Off 10 Mbps data rate
2.
1GbE
Link/
Activity
LED
Green
On Link between system and
network or no access
Blink Data transmission or receiving is occurring
N/A Off No data transmission or
receiving is occurring
1 2
1 2
1 2