lndicator Description ■■ ■■■■
Jndlcator Statua Description
Power LED : PWR Yellow LED ON Normal Power Supply
OFF Power OFF
Green LED ON Connected the PD Device, Working Normally
PoE Working LED:PoE Green LED Blink Short Circuit or Current Overload
OFF Not Connected the PD Device or Power OFF
Green LED ON Data Transmission Normally
Link/ACT LED Green LED Blink Connected Normally and Working Normally
OFF Not Connected
Green LED ON Data Transmission Normally
SFP LED Green LED Blink Connected Normally and Working Normally
OFF Not Connected
& Note : Please confirm that the PD devices are complying with IEEE802.3aflat standard.
POWER PORT : Gigabit switch series products cornes with built-in power, no power adapter,
AClOO -240V, 50/GOHz
■
■
PoE PORT: PoE port
with PoE function, which can transmit data and power simultaneously if
connected
matching device. The LED lights on the front panel can show working status of
each port.
Ethernet PORT: Beside PoE port, other ports are Ethernet RJ45 port, and ail RJ45 port
support Auto
MDIMDIX, plug and play. The LED lights on the front panel can show working status of
each port.
Connection Diagram
, "
<i>""• ... .,
'°o<>
,,.
,o c-.,"'>e,...,
,oo ,-,,,o
c-.. ,,., • .,.<i>
,00<'"
,o
c-.,"'>e.,..,
■■ ■■■■
■
■
Installation Guide
Please install with the matched devices.
Installation
Please confirm the following things before installation:
1. If the POE port power meets the power requirement of the connecting devices.
2. If the POE standard requirement and power supply matches with the power receiving device
(1 /2+, 3/6-( End -span)/ 4/5+, 7/8-(Mid-span))
■■ ■■■■
■
■
3. If the output power of the matched power adapter is compatible with the specification in the label of the POE switch
Please install the POE switch according to the following steps:
1. Put the PoE switch on the surface of a large and stable table.
2 .Connec! the power outlet through the power cable.
3 .Connec! the network devices to the POE switch port though network cable.
.&. Note:
1. Please do not put heavy products on the POE switch, and please ensure good ventilation environ ment
for the POE switch .
2. Please eut off the power first before plugging the power adapter.
Power
Connect the power cable, plug it into power socket, turn on the power, then the switch will automatically initialize,
and LED lights status will display as following:
1. Except the POE port lights, all the other lights will go through the process of "on-off-on-off", which means the
restoration is successful.
2. Power LED remains lit.
Lh
Note:
If initialization is inconsistant with the above, please check the power.
Products Model & Description
GGM GS16P: 16-Port 10/100/lO00M PoE switch, transmission distance is 100 meter,1-16 port support PoE,
IEEE 802.3af/at, the total power is 200W, built-in power.
Connect to Power
The Gigabit PoE switch uses AC 100-240V, 50/60Hz power supply
1.Please check if the power supply specification matches with the required;
2.Connect the power cable to AC power socket, shown as in the following pictures
·
-- L Angle Iron
Screw
■■ ■■■■
■
■
Power Supply Installation Display Hangers Installation Display Rack Installation Display
After installation, please check:
If
there is enough space for heat sink; if the power socket is sui table for switch specification; if
the
power, switch and rack are properly grounded and if the connection between switch and other net-
work
equipments are normal.
